Peeling Garrison Neck Lacquer (Part 1)

Рет қаралды 1,290

5 ай бұрын

Episode 2 - Guitar Spray Panting Basics - Peeling Garrison Neck Lacquer (Part 2): • Guitar Spray Painting ...
Join this channel to show your support & get access to perks:
/ @bradsguitargarage
Webpage: www.bradsguitargarage.com.au
Facebook: bradsguitargarage
Instagram: / bradsguitargarage
Equipment:
Soldering:
Pace MBT station w/SX100 & PS-90 handpieces
Hakko 474 w/815 handpiece
Hakko 936 w/907 handpiece
Hakko FX-888D w/FX-8801 handpiece
Quick 861DW hot air station
BOFA fume extraction unit
Loctite Multicore solder (C511 / 362)
Test Equipment:
Fluke 11, 175, 177 & 179 handheld DMM's
Tektronix 2236 analog oscilloscope
Rigol DS-1054z digital oscilloscope
BK Precision 4017A sweep / function generator
BWD 160a function generator
HP 6236B triple output DC power supply
Kyoritsu 3132A insulation / continuity tester
Video equipment:
Overhead cam: Panasonic HC-V785 w/Audio Technica AT9946CM mic
Handheld cam: Panasonic DC-G85 w/Olympus M.Zuiko Pro 12-40mm f/2.8
On location cam: Panasonic DC-GH5s w/Panasonic-Leica 9mm f/1.7 & 12-60mm f/2.8
Capture card(s): Magewell HDMI USB, ATEN UC3020-AT, ATEN UC3021
Headset Mic: Audio Technica BP892xcW-TH
Lapel Mic: Rode Go
Editing: Adobe Premiere Elements
Hand Tools:
Wiha, Felo, Stanley screwdrivers
CK & Engineer cutters / pliers
RS Pro wire strippers
Sidchrome & Gear Wrench spanners, sockets & shifters
Veritas planes & chisels
Materials / Consumables:
JJ's / TAD electron valves
Elixir / Ernie Ball / D'Addario / Rotosound strings
Electrolube & DeoxIT cleaners, lubricants & chemicals.

Пікірлер: 34

@matthewf1979 5 ай бұрын

Uhggg. I hate dealing with lifting finishes. You never really know if there's a procedure problem or the surface was contaminated with silicone or something. Crossing my fingers for you, Brad!

@BradsGuitarGarage 5 ай бұрын

Nah, it was just a failure to sand the cured sealer coat. Total procedural incompetence. I've done a bunch of these and they end up perfect.

@m.dwaynesteckley4832 2 ай бұрын

Ah, good old Garrison, one of the saddest guitar stories. I bought an S20 shortly after the company was making a name for itself. After a lot of study and following the glowing expert reviews I spent more than I had intended with the assurance THIS would be my forever guitar: I already owned a seventies Ibanez "lawsuit" clone, Hummingbird, but I wanted a bit better. When I got, I enjoyed it and began to play more. Unfortunately, as Gibson likely knew when disavowing the warrantees, we were realizing that while wood ages, glass composite not so much! So ended up with a crack between the neck and top: that was when I found out about the sale and rejected warrantees. fortunately, one of the original luthiers, now independent, took pity and fixed it for a good price. Now, I've strung it with nylon but it sits mostly as a conversation piece. I'm saving up for a good stable brand name: either a NA built Martin or Taylor: no more experiments. B4 anyone comments, I do understand the concept and need for hydration, but I always keep my guitars cased properly as well as living in the wettest place in Canada.

@maxwellbowden9961 5 ай бұрын

That powered sanding block is a ball tearer😊

@peterstephen1562 5 ай бұрын

The musicians in your area should be very grateful that they have such a clever and conscientious bugger as you Brad. If I might offer an idea for a fixture that I call a body vice that is super useful for holding bodies in many orientations. Take a couple of cheap sash cramps , mount the pipe ends parallel in a length of 4" by 3" about two foot apart. Fix the 4" by 3" to the bench. Attach a prop to the floor on the adjustable end. Make a couple of flexible cauls to accomodate the camber of the guitar belly and back. Mine are cork tile lined 9mm MDF. Proceed to hold bodies in all sorts of orientations.

@BradsGuitarGarage 5 ай бұрын

Thanks mate! I sometime adapt my neck-removal jig to hold all but the most annoying and difficult acoustics to work on (ie: OVATION!)

@travismccartney 5 ай бұрын

Brad go brrrrr

@BradsGuitarGarage 5 ай бұрын

If only I could work that fast in real life!

@garryparker337 5 ай бұрын

Great start, nice techniques. Thanks for the tip with sharpening scraper I've only used the squared edge, no burr

@BradsGuitarGarage 5 ай бұрын

Oh man, that must have been tough going with no burr! Here's a good article on how to prepare the edge: www.stewmac.com/video-and-ideas/online-resources/how-to-install-and-repair-instrument-binding-and-purfling/how-to-sharpen-a-scraper/

@BradsGuitarGarage 5 ай бұрын

And another one: www.rockler.com/learn/sharpen-burnish-cabinet-scraper-steps

@garryparker337 5 ай бұрын

Now that I've seen a few diagrams, dragged up some memories of my old woodwork text book from school. Cheers

@brucehayes7251 5 ай бұрын

Evening Brad, it may be a little different but I know from experience with floor finish that I have to rub back between coats to key the finish for next coat as well as improving the surface finish. A particularly impressive peel in a hallway many years ago was the result of me not sanding up close to skirting on a recoat, finish was yrs old and needed a refinish, same product used both times only my lack of attention caused the problem

@BradsGuitarGarage 5 ай бұрын

Yes, "Keying in" is the term I forgot to pinpoint. I've been spraying polyurethane since around 1999. I learned the hard way to CLEAN YOUR GUN thoroughly as a result!

@sgt.grinch3299 5 ай бұрын

Greetings Brad. Let’s Roll Sir!

@peterstephen1562 5 ай бұрын

Also. Put some surf fishing rod grip or pipe insulation foam over the pipes to protect the instrument. If the cramp pipes are long enough then guitars can be held flat to work on the top and back by haveing block to take up the narrower upper bout.

@PsionicAudio 5 ай бұрын

Ah, the scraper… what’s the opposite of ASMR?

@BradsGuitarGarage 5 ай бұрын

I like the way it sounds. It sounds like progress when it digs in.

@murrayguitarpickups9545 5 ай бұрын

Hey man with those masking skills you had me asking "is Brad a qualified painter?" but that garbage bag idea mate.....you got the right idea but a real painter would use anti static plastic, if you do a lot of painting it'd be worth going down to a crash shop and asking for a few metres, or even grab their scraps, it'd be absolutely fine for your purpose. Having said that, overspray isn't a big problem for a guitar paintjob, not like a car respray so I'm sure you've had no issues but if you want to step up your painting game there's a tip for ya.

@tedmich 5 ай бұрын

Nice Lutherie Brad! It looks like a Mfg got sold a bill of goods by (finish) supplier without testing, a fairly common scenario.

@dcallan812 5 ай бұрын

Different doing wood finishing work. Great video 2x👍

@BradsGuitarGarage 5 ай бұрын

Thanks 👍

@marktelfer8900 5 ай бұрын

Reminds me of the bionic man how fast you were sanding Brad😅

@megwatts1903 5 ай бұрын

I think the blue and white on the headstock gives it kind of a racy feel....

@bbmade 5 ай бұрын

Is it a catalyzed coating? Pretty wicked adhesion failure between the sealer and topcoat from the appearance on a video.

@bbmade 5 ай бұрын

Ah, if I just keep watching you answer the question in the video.

@BradsGuitarGarage 5 ай бұрын

Yes. A poly-something-or-other.

@baabaabaa-yp2jh 5 ай бұрын

Isnt poly a bastard!?! Never seen bracing like that. I (stupidly) put my hand up to strip an LTD.... Scraping it back, l found about 7 coats, metallic red and gold..fmd! Luvd the 5x go fast sound effects Brad.. Benny Hill wd be proud!!

@BradsGuitarGarage 5 ай бұрын

I actually prefer poly, to be honest! This is attributed to the incompetence of the manufacturer. What other finish allows me to spray one afternoon, then cut and polish to a mirror gloss the next morning!?

@baabaabaa-yp2jh 5 ай бұрын

@@BradsGuitarGarage Yeah mate, hanging nitro for wks to cure slows the process down a bit!! I still have nightmares scraping that LTD tho!!

@goodun2974 5 ай бұрын

Fix that crackered, fractured, knackered lacquer, and don't be no hacker or slacker!😅 (PS, I never really thought about how many words you can make just by adding Acker to something).