Perfect Paint for a VINTAGE 12" Jointer - Restoration How-To [Part 1]

Рет қаралды 13,521

3 жыл бұрын

BUILD PLANS FOR SALE:
scottwalsh.co/collections/plans
In this video, I begin to restore a vintage, Kasto brand, German jointer.
I begin by cleaning all the rust off the parts with Evaporust. It works so well! Just rinse off with water and clean with penetrating oil and maroon Scotch Brite.
Next I tried and failed to use a chemical stripper. It's not the fault of the stripper, it's just the original paint, primer and filler was too thick to penetrate.
I successfully took the rest of the paint off with a clean 'n' strip disc on my angle grinder.
After cleaning with mineral spirits, I can start applying bondo. I used a drywall rasp to knock down the high spots and then finished up with some sanding.
I started with a self-etch primer by Rustoleum, then switched to a filler primer by the name brand. Then I used "Black Stainless Steel" spray paint by Rustoleum and I think it turned out amazing!
I partially assembled the machine for your viewing pleasure. I will need to machine some parts that had previously broken. Let me know if you want to collaborate on this!
All music by Corbyn Kites:
/ @corbynkites8006
PLEASE Like and subscribe, it's the only way I can reach more people!
Also, follow me on insta: / scottydwalsh
US & CANADIAN AFFILIATE LINKS:
DOWELMAX:
DOWELMAX 3/8" Kit:
www.dowelmax.com/product/clas...
DOWELMAX 1/2" Expansion:
www.dowelmax.com/product/dowe...
BLADES:
Table Saw Blade: lddy.no/1gj1k
Miter Saw Blade: lddy.no/1i8tz
Dado Stack: lddy.no/1g6ux
TOOLS:
Chisels: lddy.no/1g68v
Miter Gauge: geni.us/0K4H36
Dust Extractor: geni.us/ccOkLC
Drill and Driver: geni.us/qyrTiC
Circular Saw: geni.us/J5mDQ
Random Orbit Sander: geni.us/dkULx8s
Jig Saw: geni.us/i7HRN
Compact Router: geni.us/h90weiY
Cordless Router: geni.us/Jou0
Miter Saw: geni.us/uhfOe
Track Saw: geni.us/aslB
BITS:
Forstner Bits: geni.us/oj2HXU
Countersink With Stop: geni.us/cQFDp
Countersink w/o Stop: geni.us/dMiEM
Countersink Zero Flute: geni.us/fVIhcp
Self-Centering Bits: geni.us/RXZv9K3
3/32" Round Over Bit: geni.us/b8sGMT
SUPPLIES
Sandpaper: lddy.no/1hs32
Double-Sided Tape: geni.us/ZohrzD
Green Tape: geni.us/CWZquR
Glue: geni.us/4JCcR
CA Glue: geni.us/mELd05A
CA Accelerator: geni.us/bq0Az2
Silicone Glue Brush: geni.us/tiJw
INSTAGRAM:
/ scottydwalsh
MUSIC:
Epidemic Sound
Use my referral link and start your free 30-day trial:
www.epidemicsound.com/referra...

Пікірлер: 56

@Raptorau 2 жыл бұрын

Keen to see more of this when you are able to access the tools you need. I'm deeply enjoying your channel, thanks for the entertainment!

@alexgoyetche8311 3 жыл бұрын

i don't know what a jointer is, but I sure enJOINT'd watching this video

@ScottWalshWoodworking 3 жыл бұрын

I was going to respond with a jointer pun, but I thought it'd fall FLAT

@Thurge 3 жыл бұрын

@@ScottWalshWoodworking I'm going to need a co-planation for this tangent...

@thisguy349 Жыл бұрын

I have looked at older woodworking tools and thought this might be a way for me to get something beefier. The one thing videos like this doesn't fully illustrate is the time needed to restore them. Time is not a luxury i have with also having a mini me. I am looking forward to seeing part 2!

@ridebadger 3 жыл бұрын

I suggest "This Old Tony" as a machinist collaborator.

@colemine7008 3 жыл бұрын

that was my first thought

@arimadx 3 жыл бұрын

Loved the video! I was incredibly bummed to see that I couldn't binge the rest of the episodes to this project though! 🤣 cant wait to see what you come up with!👍🏻

@ScottWalshWoodworking 3 жыл бұрын

I'm bummed too! I really want to use it! I didn't think it would take this long for the machine shop at my school to reopen. Hopefully sometime in the Fall I may be able to get in there and machine the parts I need to complete it. Thanks for watching!

@origin_l4613 3 жыл бұрын

Avid watcher Scott, I'm so happy you have a channel! Luis here!

@ScottWalshWoodworking 3 жыл бұрын

I'm so glad you liked it Luis! Hope you're doing well!

@codycates3427 2 жыл бұрын

silver lettering would look awesome

@timl3918 Жыл бұрын

Next time....choose PVC pipe slightly oversized of your cutterhead, glue and cap the base, fill the pipe with evaporust, submerge your part, then cap and let sit overnight. This method uses less evaporust and prevents those annoying lines left over by the towels.

@apro6531 2 жыл бұрын

Great project, impressed with your skills. Continue the project please :)

@Wheelzroll 3 жыл бұрын

Well done Scott! Looking forward to your progress!

@ScottWalshWoodworking 3 жыл бұрын

Thanks so much for watching!

@billymacmakes 3 жыл бұрын

Great start to restoring a great old machine!! Looking forward to seeing the rest. Subscribed!

@ScottWalshWoodworking 3 жыл бұрын

Thanks so much for watching Billy! I can't wait to get it up and running.

@bobruddy Жыл бұрын

Looks great!

@dreamcatcherdb 3 ай бұрын

I was drawn to your channel by your recent cabinet build video...great video BTW. But I have a real passion for machine restoration and my own vintage Porter 12" jointer restoration project gave me some real empathy for what you are up against with your jointer restoration. I tried looking up your jointer but I was not able to find any comparable models. In fact, I couldn't even find that Kasto ever made a jointer. I did find one Kasto hacksaw image with a simiar looking base casting at a site called "metaalnieuws" out of the netherlands. Looking at the writing on the cutter head it says something like "Polaree(?)" which I also haven't heard of. You may have the only one in existence. It could be a one-off, a prototype, a war-era fabrication, or just a DIY frankenstein of sorts......which is going to make restoring it a bit difficult if not impossible. It may help if you could better document the parts and assembly.

@1974HondaCB350F 3 жыл бұрын

I am about to start a restoration of my Crescent P18 planer and found your information about cleaning and paint removal really helpful! Evaporust was already on my list of things to buy, but that clean and strip disc was pretty slick! I'll have to add that :) Thanks for the video!

@ScottWalshWoodworking 3 жыл бұрын

Sounds like an awesome project! Clean and strip discs are great and highly effective without removing metal beneath the paint. They won't reach in every nook and cranny but they'll get you most of the way. Thanks for watching!

@mmanut 3 жыл бұрын

Finish it, Do it right. Beautiful Machine ‼️👍👍 PS New Subscriber, Vinny 🇺🇸

@ScottWalshWoodworking 3 жыл бұрын

Thanks so much for watching and subscribing, that means a lot! I'll be finishing it as soon as I can access my school's machine shop, whenever it reopens again, post-pandemic. Cheers!

@JakeEllison94 2 жыл бұрын

Blue

@michaelhayhoe2540 3 жыл бұрын

I hope you can have the missing / broken pieces replaced. I really would enjoy seeing the jointer completed.

@ScottWalshWoodworking 3 жыл бұрын

Thanks Michael! I fully intend to machine the missing and broken parts. I need to make two knobs for the infeed and outfeed elevation mechanisms. I have one broken one to copy from, the other was missing. I need to make a shaft for it too, I have one good one and a broken one. I need to figure out how I'm going to make a guard for the cutter head as well. Cheers!

@sharonsalsberg2646 3 жыл бұрын

I'm thinking bubblegum pink!!!!

@ScottWalshWoodworking 3 жыл бұрын

now we're talking

@raymondgoodman9148 2 жыл бұрын

this is the answer - if it were me, I would paint the recessed background so the letters would remain black.

@bradboyer1381 Жыл бұрын

Gotta echo the rest of the gang...let's see part 2 (or 3 or 4?)!

@lilolmecj 2 жыл бұрын

Lol on opening the paint can! I usually end up smacking it against the edge of my work bench in frustration. This method has its drawbacks, including sometimes damaging the spray gadget. Probably should just hand it to a four year old, probably would open it more easily than I. Great job on restoring it, I would not know where to start!

@ScottWalshWoodworking 2 жыл бұрын

Thanks Carole!

@hdwoodshop 2 жыл бұрын

What if you do epoxy pour into the name then sand to flush. Shweeet! 👀

@ixamraxi Жыл бұрын

Hows this project going? Any progress?

@kenzaphilips3418 Жыл бұрын

Is it working already?

@rachelsalsberg5011 3 жыл бұрын

Very cool!! Maybe you could still paint the lettering red, just a more subtle shade!

@ScottWalshWoodworking 3 жыл бұрын

I'm leaning towards silver at this point, a monochromatic jointer will be neat.

@Thurge 3 жыл бұрын

I was thinking silver also. Tape the area around the logo and roll on silver so that only the surface of the letters get any paint. That'll make it pop! Also what was the name of the marketplace where you first encountered this beast? I want to find one that size to rebuild...

@ScottWalshWoodworking 3 жыл бұрын

In most parts of Canada, Kijiji is more popular than Craigslist, but it's essentially the same type of classified ad service. The best deals go fast, so if you're looking for something, try and look every day. Also helps to have more generalized searches: simply 'jointer' will turn up all results, which will include those that are too lazy to give more detailed descriptions. In my experience, the ads without much effort by the seller tend to give better deals.

@Thurge 3 жыл бұрын

@@ScottWalshWoodworking Craigslist isn't as exhaustive as Kijiji seems to be. Maybe there aren't enough woodworking types in my area? I guess I need to find a buddy in Canada who would hunt down a deal for me and help me acquire this tool. I suppose it will require a JOINT effort! LOL!

@chippychippy8291 Жыл бұрын

Have you finished yet?

@andydeciccio 2 жыл бұрын

Keep the lettering black. Make the background red

@bmalovic Жыл бұрын

Only propper colour for German machine is RAL 6011 Yes.. Germans have standard for machine paint :) DIN 1844

@whitexeno 9 ай бұрын

Part 2 when?

@Scarecrowking Жыл бұрын

Dang ma boi just angle ground lead dust all over the place

@chelseasalsberg6914 3 жыл бұрын

LOL RACHELS CAMEO.

@rachelsalsberg5011 3 жыл бұрын

Believe it or not, we filmed a little skit and he decided not to use it and CUT ME OUT and just left this shot of me nagging him hahahah

@theweekendwarrior6355 2 жыл бұрын

You finish this jointer yet?

@ScottWalshWoodworking 2 жыл бұрын

Couldn't work on it because I don't have access to the machine shop I normally do because of the pandemic. I might finally be able to get in there within the next month or so if all goes well.

@theweekendwarrior6355 2 жыл бұрын

@@ScottWalshWoodworking I understand, you stated that in the video, was wondering if enough time went by for the shop to open back up. But glad to hear you don't have to wait to much longer.