I did the same in my 1985 M-B diesel engine. Ignore the naysayers. The liner is just thin cast-iron, so breaks easy. On the 1st cylinder, I first ran a weld bead down the liner, as I read on the internet and others state here. But it didn't just drop out so I started tapping w/ a small chisel on the edge from the bottom side. The liner starter folding in, so I inserted a thin screwdriver and found it tapped down easy, folding in the liner. Now smarter, I skipped the welder on the other 4 cyl and just worked the screwdriver in and got each out in 1 min. I hit harder than shown. You can then fold in the liner to drop it out. I had more trouble getting the new liners in. Heated the block over a gas stove and left the liner in the freezer, but still had to place a thick plate on top and beat w/ a sledgehammer. You can hear when they seat at the bottom.

I've done similar by tig welding 316 down the side of the sleeve it shrinks it enough to remove with the grips just the same!!! nice vid!!!

Good work. Clever stuff. Thanks.

Thanks for the great video. I'm going to use the same method to remove my sleeves. I hear people saying to use a puller, because you could damage the bores with a screwdriver, but a person would probably have a greater chance of damaging the top of the engine by putting all that crap on top of it and exerting that kind of force. On top of that, it's gonna take alot more time to press them things out.

I've done this lots of times, but used a rosebud tip. Run down the sleeve wall, and you'll see the sleeve bulge toward the center of the bore as you go. Go have coffee and come back 20 minutes later. They fall out with no damage to the block, which is more than can be said for using a sleeve puller.

Good information and useful. Solutions are always based on resources. I've used the arc welder procedure but it scares the hell out of me. Afraid to get too much penetration. This looks less imposing for collateral damage, I like it!! I get a kick out of some of previous comments. Not everyone works factory!!!

thank you great to see and very helpful

i use a stick welder, run beads down the bore and the liner will come right out when cool

You got to do what you got to do.

Super impressed.. very clever.

Nice job sir

ive watched several youtubers doing it this way,,not all use heat as well tho,,now gonna try it on my dexta,

Run a bead of weld down the inside of the liner, when it cools down the liner cracks and then you just pull it out, I worked on perkins engines for years

That is cool for saving money!

Heat it with torch or weld bead, let cool and the sleeve shrinks. Heat it with torch, cool it with water, sleeve shrinks. When you weld something the weld joint shrinks, sweating panels is the same think. Shrink it let fall out.

Dear Lord ............

Qlot of keyboard mechanics in here.

Graet Job.! Thanks for upload.

Well, I guess there's a good reason this video is in the comedy category

Much much easier to run an MMA electrode quickly up the inside of the sleeve a couple times and shrink it doesn't put heat into the bore like you did could see vapor rising out of the water jacket holes

Its definitely not a procedure recommended by manufacturer... Have You heard about hydraulic press? Old cylinder liners/ sleeves should be pressed out from bottom. That is Perkins recommended way

Very interesting, I knocked them up from the bottom on a '58 IH 4 Cyl with a blunt round stock chisel with plenty of penetrant and oil squirt can. No heat was necessary. they were thin and rusty like old beer cans. I also have this eng. in another hoe so- very interesting P.S remember that gut on "Laugh-In" who always said "Very Interesting"? : )

thats a cool video(more than one way of skinning a cat) your teaching people there are other methods to get a job done, without having to use an expensive service tool

or use the freezing method to shrink the sleeve.

One stringer bead down the inside liner an yes they'll fall right out.

OR WELD A BEAD AROUND INSIDE OF SLEEVE AND IT WILL FALL OUT.

I don't believe that is the recommended procedure.

Can help set the timing fuel pump timing on 3034 Perkins

if works whats the problem??

hell if i can get my dexta liner to come out like that ,,i cant even get anything between the liner and the block,,its as if my liners are cast and your,s are like tin,,ive tried the heat like you ,,and ive even tried the weld from top to bottom x2 and then tried pulling with a drawer,,all to no avail,,ive now orderd a 3 inch angle grinder to try cutting a grove,,..yes i know i need to be carefull but what else can i do,,

SLEEVE PULLER! Engine work isn't carpentry!

Simply turn the engine around and hit from the otherside..

How did u get the oil pan off ??

I'll use this trick when im in a machine apocalypse like in terminator otherwise i will trash talk your method. Or until one day im stuck and have limited tools then youll find me doing it... But lets hope if it comes to that i can bore it out until it tears first

Ouch! puller....

So no warping when heating one side of a cylinder wall like this ? Did you test for any oval shaping ?

Big chance to damage the block

Genius!!!!

any supplier the all MF parts outside there? Please email to me how i address You.Thanks

Arc air cutting is easy

wyjmowanie tuleji mokrych prawidłowe ale te drugie to podejrzewam że zostało uszkodzone gniazdo tuleji

How NOT to do that...

not a good idea, you risk the chance of cracking the parent bore. im a gactory trained perkins tech perkins say use a puller i have done it in the field with a welder but you have to run 3 beads from top to bottom and they come right out.

if it works, I see no damage - good do this who care if your scared take to machine shop $25 per sleeve press out

what ever works

I welded cast steel blocks. There is nothing wrong with what he is doing.. Come on.

WHY NOT USE A LINER PULLER

ME GUSTA MAS SACAR LA CAMIZA CON HIELO SECO .

Buy a liner puller before you overhaul

for fuck sake

He won't be working on my engine buy the proper tools or leave the job alone

this is not the way I do this now, it is the same only without the torch much faster and no heat necessary. As to the "using a press" comments I don't have a press and the all time to set all that up. I saw on youtube guys using an air hammer so i thought I might improve the process. thanks for likes 262K who would've thought.