2015 Honda CR-V MIL on P0341 Cam Timing Error

Рет қаралды 29,858

3 жыл бұрын

Diagnosing a MIL on with other warning lights as well as P0341 cam timing error code. Stretched and worn timing chain. Replaced timing chain, tensioner, guides and VCT actuator to correct.

Пікірлер: 29

@donaldramsamugh1723 3 жыл бұрын

Great video brother, My neighbor having the same problem right now and need a good mechanic to do the job..

@markferraro5250 3 жыл бұрын

great videos PB thanks

@Striker50_ 3 жыл бұрын

Great video I keep getting a P0339 crankshaft position sensor. Would you happen to know what the fix is? Thanks in advance

@PhillipBailey 3 жыл бұрын

Does the engine crank at normal speed or does it sometimes turn slow. Code could be caused by low battery voltage, loose or dirty cables or failing starter. If it cranks over normally but sometimes longer to start its probably a failing crank sensor. Inspect the connection and wiring and if it looks OK probably recommend to replace the crank sensor. Good luck.

@kriscabanero 2 жыл бұрын

Thank you for this video. How did you hold the intake cam in place to remove the VTC actuator?

@PhillipBailey 2 жыл бұрын

You can use an open end wrench on the hex on the intake cam. Sorry I didn't show that.

@kriscabanero 2 жыл бұрын

@@PhillipBailey thank you. Upon inspecting the intake cam, looks like the only spot that has a hex for a wrench is at the end towards the in inside of the high pressure fuel housing.

@vampirel1983 Жыл бұрын

I have done 2 of these already. One without taking the timing off cover one includes replacing the chain and tensioner. As i can remember, i actually talked to couple nice techs from honda service department before i did these jobs and they told me usually its the chain and the tensioner that needs to be replaced. So i didnt replace the actuator on the other job i did and it worked. But i am curious how to determine the actuator is bad.

@PhillipBailey Жыл бұрын

Cheap insurance either way. Sometimes you can see that it's stuck or it won't click when energized.

@adra8409 2 жыл бұрын

Gr8 video, quite helpful, Please recommend a good tech in Toronto for Similar job ….CRV 2014 EX

@PhillipBailey 2 жыл бұрын

I'm sorry. I can't recommend anyone as I'm 1000 miles from Toronto. As friends and co-workers who they recommend is your best bet. There has to be a reputable shop for sure. Good luck

@mrpistonrecaro6483 2 жыл бұрын

Do you know where to find the timing marks? I tried but no luck. Also how did you break lose the vtc gear?? Mines so tight

@PhillipBailey 2 жыл бұрын

Timing marks are shown at 10:51 and again starting at 13:45. There are hexes cast into the camshafts that you put a wrench on if I remember. I have a home made holding tool that holds the cam sprocket if it has slotted holes in it.

@anilcetin9629 9 ай бұрын

What could happen if we keep driving like this? I have same exact problem. I bought a car from private seller, he put electrical tape on all those lights..... already spent quite some money. Don't have budget in short time of period... And where can I get the oem parts provide to mechanic. I'm not quite sure if he's gonna use oem parts.

@PhillipBailey 9 ай бұрын

If the chain jumps time due to excessive wear it will likely quit. If it goes out of time far enough some valves can contact pistons resulting in major damage. I'd recommend dealer parts but if you are not doing the job yourself let the shop supply the parts because if you supply parts you won't have any warranty on labor. Some shops won't install customer supplied parts.

@anilcetin9629 9 ай бұрын

@@PhillipBailey thank you. I'll find good mechanic and let them do the job.

@marcandresabourin7473 11 ай бұрын

Vtc solenoid is different than the vtec solenoid

@SweenBean-420 8 ай бұрын

And how much you charging these ppl? Pretty penny for vtc run and oil change.😁

@PhillipBailey 8 ай бұрын

This was several years ago. Now these repairs would run around 2k Canadian

@theacademy1734 2 жыл бұрын

That should be cover under Waranty 50k miles

@PhillipBailey 2 жыл бұрын

The Honda dealer denied warranty as its over 50k miles.

@petelambaren3462 2 жыл бұрын

2010 Honda acc

@jairohernandez7957 3 жыл бұрын

How much would this job run me?

@PhillipBailey 3 жыл бұрын

Roughly $750.00 for parts and 6 hours labor plus tax. Cost my customer $1350.00 plus tax but thats Canadian dollars.

@jairohernandez7957 3 жыл бұрын

@@PhillipBailey thanks for the reply!

@donaldramsamugh1723 3 жыл бұрын

@@PhillipBailey hey Phillip, Where are you located please?

@PhillipBailey 3 жыл бұрын

@@donaldramsamugh1723 Just outside Thunder Bay in Ontario Canada Eh...

@donaldramsamugh1723 3 жыл бұрын

@@PhillipBailey thank you, A bit too far, we're in Milton ont. Keep on doing your thing you know your stuff..