Silicone Render | Best & ONLY RENDER To Use...

Рет қаралды 129,198

2 жыл бұрын

Sand Cement is ok...but it's rubbish on timber. And it just doesn't cut the mustard. Which is why we made this video!
We'll show you the ONLY way to render onto a timber frame build. We'll show you the best products to use, the preparation involved and finally outline the renders we used for the job.
It's a full guide to my new favourite rendering system, Silicone render. The Link to the render mesh we used on the job is in the link below:
----
amzn.to/3mZoeeE
----
Subscribe to our channel from the link below: / plasteringforbeginners
If you like this video then please like, subscribe and leave a comment because we'd love to hear from you.
Thanks for watching. I'll see you one the next one.
Cheers.
Blaine Gray,
Plastering For Beginners

Пікірлер: 200

@chloedensham4809 Жыл бұрын

Can I just say a massive thank you to you. From your videos, I have re-plastered a whole bathroom Inc ceilings AND microcemented the shower and floor based on your content, tips, resources, and guides on materials. AND I did a pretty decent job! Thank you for sharing all the finer details. Hats off to all plasterers as my hands and arms are dead!!! ❤

@PlasteringForBeginners Жыл бұрын

That’s amazing!! Well done - you should be proud!

@Andrew_Tate_Personal 2 жыл бұрын

A master in his trade. I would hire him without question for plastering. Keep up the great work

@darrenmorgan6735 2 жыл бұрын

Nice job and you make it look so easy I love to give that a go.

@danielstokoe6564 2 ай бұрын

Well explained mate, top video tells you everything 👍

@frank__rizzo848 Ай бұрын

Here's a thin coat rubbing up tip for ya mate, when rubbing up, fill a gorilla tub half with water, and use two floats to rub up ( not at same time ). hang one on the side of the tub and use the other, Clean it every 10/15 secs and then use the other one that's been hanging on the side drying out, and repeat Ive always found if your float is constantly clean it glides without any drag.

@jaycutts8054 Жыл бұрын

I’m sure you know as you get through half the roll of mesh it gets very springy, top tip, hose down the mesh and it takes the spring out of it, nice vid 👌

@ryanjodrell1131 Жыл бұрын

This guy’s lessons helped me plaster my flat from top to bottom. Good teacher and top plasterer

@PlasteringForBeginners Жыл бұрын

Great to hear that mate and thank you for watching! All the best 👍

@apollocreed85 2 жыл бұрын

In the summer time with warm air I recommend using a hopper gun as it will go elasticated quick by hand if doing a big area but it's ideal to apply in winter months by hand as it dontgo off quick

@shirleynick1 11 ай бұрын

Great videos mate....got me out of a load of trouble👍👍👍

@RichardDowd 2 жыл бұрын

Great video and finish as always Blaine.

@PlasteringForBeginners 2 жыл бұрын

Thank you matey!!

@hope56 Жыл бұрын

Another great video! Thanks

@btendanhiggins5429 Жыл бұрын

Top class buddy really really good it's the best video I've seen so far fair play

@georgeomalley6066 2 жыл бұрын

Great Detail, Preparation is 🔑 to 1 Man Application, MacGyvering the Primer 😂🤣😂, Needs must, Top Channel 👏👏👏🖖

@TaraBryan. 2 жыл бұрын

Hi Blaine. Hope you're well my friend. Love the video! It was really informative. You give so much information out which i love. As a beginner i love to get even the tiniest of details. 'I'm not even sorry' haha love it!

@PlasteringForBeginners 2 жыл бұрын

Hi Tara, how’s it going?? Thanks for watching - really appreciate it as always and it’s great to hear that it’s helped. Hope your Plastering is going well - keep it up. You’re a pro 👍

@benwilkinson5457 2 жыл бұрын

Nice vid mate. Thanks for sharing. I will give this system a go

@PlasteringForBeginners 2 жыл бұрын

Cheers pal!!

@helenez2318 Жыл бұрын

Very neat great job

@jimrivets8678 2 жыл бұрын

Well done mate

@lewisriggs6596 2 жыл бұрын

Great video very informal great job 👍🏻👌

@PlasteringForBeginners 2 жыл бұрын

Cheers pal!!

@viankalobosvalenzuela7456 2 жыл бұрын

Excelente trabajo 👊 👏

@PlasteringForBeginners 2 жыл бұрын

Thanks mate!!

@occidentadvocate.9759 2 жыл бұрын

Im a Decorator, done bit dot and dab too. I wouldn't mind a go at that. Nice to see a quality trades man at work. Great job mate. 👍

@PlasteringForBeginners 2 жыл бұрын

Cheers mate!!

@rockroll456 2 жыл бұрын

Brilliant bud

@zulfiqarali-fm2vs 2 жыл бұрын

You are very with your skills and informative mate 👍

@PlasteringForBeginners 2 жыл бұрын

Thank you my friend 👍

@gerarddunmoore7609 2 жыл бұрын

So true what you say about checking your stud work’s true - the last Workman always gets the blame!

@barryleete9853 Жыл бұрын

Hi Blaine love your videos quality work as always I got my second silicone job to do in weeks time on new concrete blocks. Would you use 6mm beads or 3mm mesh beads that you used here thanks Barry

@peterdavies5454 9 ай бұрын

Hi Blaine, I’ve recently subscribed to your channel, and I can’t believe how much I’ve learnt from you. Until this week I had never tried silicone and the Refina power float is a real game changer. One question I have however is I used Johnson’s render however I noticed you praising Webber OCR, which I might add is 30% cheaper, can I mix OCR base coat with Johnson’s top coat. Thanks again for sharing your knowledge and expertise Pete

@immers2410 10 ай бұрын

Nice to see Kell Brook has found work dubbing KZfaq videos

@tonybeards2978 2 жыл бұрын

Nice one mate, but to be fair i love the k-rend system

@312saxon 2 жыл бұрын

Beautiful

@PlasteringForBeginners 2 жыл бұрын

Thanks pal!!

@davidstewart2 2 жыл бұрын

100% right two on the finish coat, keep it thin as, miles better than scratch back

@peterjones6226 Жыл бұрын

Nice job, and some useful tips 👍. Is there much difference to the cement board system and the EWI in terms of materials?

@nigelsmith1198 2 жыл бұрын

I use a product from EWI store, awesome product and great service. You do make it look easy and yes definitely need 2 people.!

@CamberKitesurfing Жыл бұрын

Would you recommend corner bead with nose or without, i'm just about to order ewi. I guess rendering to a nose is alot easier but noseless the product goes right round the edge

@overdrivehd4529 Жыл бұрын

@@CamberKitesurfing definitely a corner bead, you’ll find the material will go around the bead

@CamberKitesurfing Жыл бұрын

@@overdrivehd4529 with or without the nose or doesn't it matter?

@blakeevans2963 2 жыл бұрын

Aup mate. Thanks for the acknowledgement about the gap. It's all about picking things up from other people nobody knows everything. I always use like a 2ml window packer or something like that. But again mate your always there to pass knowledge on but also give credit to where you got it from. Gets you more respect than alot of these jonny I come up with everything tradesmen. 👍👍

@blakeevans2963 2 жыл бұрын

Them beads are horrible I hate them

@PlasteringForBeginners 2 жыл бұрын

Haha cheers mate! I’m always learning and I like to point out the people who provide the knowledge. Thanks again…you’re a legend 👍

@mikevlek Жыл бұрын

Have you checked if the small mesh you use on the joints is rated for outside use? Renders can be corrosive to the mesh. Thats why you use differnt mesh than for inside plaster. Just a little tip

@damienwilliams9997 2 жыл бұрын

Great gear we found 6l of water is the best to work with.

@durexjim 2 жыл бұрын

Great job i think its a little similar to high build we used to use in the 80s

@PlasteringForBeginners 2 жыл бұрын

Cheers pal!!

@MrWiffwaff 2 жыл бұрын

Hi Blaine, thanks for another excellent and informative video. Keep them coming! Wonder if you can advise on a project we're planning. Our house is finished in Roughcast and we're having a small dormer window fitted and we'd like to do the front and cheeks in a similar finish. Obviously this would be a silicone based system onto render board but I cant seem to find much info on which system to use for the roughcast finish. Is that something you have any ideas on? Cheers.

@Mitzy-0409 2 жыл бұрын

Awesome content as always 👊🏻👍🏻

@vincemarshall8550 Жыл бұрын

enjoyed that mate ,can this stuff be used on masonry /blocks etc? if not what would you recommend ,i hate working with traditional render materials ,cheers

@beatonthedonis 2 жыл бұрын

In central/eastern Europe, where you don't have cavity walls and many are going for EWI, silicone render is now standard. Only drawback is you need to work mob-handed on larger areas. Apart from that, it's durable, repels water and dirt and doesn't need painting.

@benreeve9130 2 жыл бұрын

Doesn't repel algae though

@beatonthedonis 2 жыл бұрын

@@benreeve9130 Traditional render/ masonry paint can also develop algae. You can jet wash silicone render.

@benreeve9130 2 жыл бұрын

You must soft wash silicone render, jet washing will damage it.

@beatonthedonis 2 жыл бұрын

@@benreeve9130 Gentle jet wash is fine. ewipro.com/2020/07/24/how-to-clean-ewi-pro-renders/

@lloyds053 Жыл бұрын

@@benreeve9130 what's better mate k rend silicone or silicone rend in the tub?

@timwilcox960 Жыл бұрын

Hi Blaine, Very instructive video, thank you. I'm building a timber framed extension that I want to render - but I have no intention of doing it myself! So, I'm trying to find a local firm (I live in South Devon) that will do a pukka job using bespoke products - just as you've done here. Any pointers as to how I can find someone (assuming you're not local to me) would be really helpful. Cheers!

@jessehaze5754 2 жыл бұрын

I really want too give this a go, lovely finish. Is prb the same thing?

@yerzhanabilakhatov9099 Жыл бұрын

👍 good

@nickparks1982 2 жыл бұрын

Hi Blaine, which brand of render and where stock it? Pleasure to watch you as always.

@AdamSmith-lr2fz Жыл бұрын

Thanks so much for this video, what is the bead you are using at the bottom, im struggling to find a thin coat drip bead!

@lea-rw5cb Жыл бұрын

Silicone based render used it for 20yrs so easy to use 👍👍 STO,KREND,EGLINGTON , I actually started on structherm with a macerend finish but after 20yrs id had enough of chasing ££££

@jamiec4108 Жыл бұрын

How much water did you add to the top coat when hand applying k rend tc-15?

@lea-rw5cb Жыл бұрын

@jamiec4108 I used to put 2 cups in sto and Wetherby top coat never used tc15 or I have and they've changed name lol you can tell when your towelling it on if it's too stiff and maybe add more water, we were advised on some topcoat to add methspirits instead of water. Adding water also depends on the humidity as well 👍

@DuskCookies 2 жыл бұрын

Johnstones silicone, use flexii to apply and scrap back is what i normally use

@PlasteringForBeginners 2 жыл бұрын

Sounds good to me!!

@montyjones640 Жыл бұрын

As of k rend recommendation to get the warranty and guarantee you should really hpx base cement board

@slyteen2197 2 жыл бұрын

Would like to see a video of how to go about rendering external wall insulation

@sirazsaleh5942 2 жыл бұрын

Hi Blaine, do you have the link for the soil pipe where you had the level , I think you were talking about the cut out .

@scottlandeg7375 2 жыл бұрын

Cracking job mate ! Where do you buy this product?

@UrbanTreats 4 ай бұрын

Hi Blaine, thanks for the great tutorial. I am based in Cyprus and the weather is very hot, I am worried that doing it alone it will dry on me too quickly. Do you need to render a whole wall in one go to avoid connection lines?

@DotAndDab 2 жыл бұрын

Nice video

@PlasteringForBeginners 2 жыл бұрын

Cheers pal!!

@jasc6904 2 жыл бұрын

Top tip it’s great for bathroom ceiling

@PlasteringForBeginners 2 жыл бұрын

👍👍

@Pinkpanter.plastering 2 жыл бұрын

Try a Notch tiers trowel before putting the mesh it’s flater then just a tip and might be helpful

@kaimichael5444 Жыл бұрын

Hi pal hope u well this is all I doo now rendering. Quick tip not that u need any always quality. When I'm laying on I put bout metre on. Then when scraping back use a Swiss trowel pal soo much easier. Google Swiss trowel quality for thin coat render.

@SprintsNClimbs 2 ай бұрын

Great vid thanks, do you have a link for the type of drip bead you have used?

@davet9900 Жыл бұрын

Would you say this is a better alternative to the thick polystyrene insulation and the thin render (that is put on after it)? Thanks

@interestingvideos4728 Жыл бұрын

I want to render the front of my house. I have pebble dash. Would you recommend stripping away the pebble dash, then use a fibreglass mesh and silicone render?

@marcomorgera6180 2 жыл бұрын

hi i am a plasterer who has always used low end trowels, i am looking for a better trowel that can be good for the smooth plaster that is applied before the grout. could you recommend the right trowel for me?

@ROADRUNNER555 Жыл бұрын

Mate can you use this if temperatures drop to -6c at night? im in chamonix france for a week and have the opportunity to render a house here, im guessing it will be too cold but the weather is pure sun in the day and about 2c max in the day and -6c lowest at night, any advice would be very much appreciated! love your videos!

@shodan198 2 жыл бұрын

Nice job mate

@PlasteringForBeginners 2 жыл бұрын

Cheers mate!! Hope you’re well my friend 👍

@shodan198 2 жыл бұрын

@@PlasteringForBeginners yeah mate steady work coming in

@PlasteringForBeginners 2 жыл бұрын

Good man!

@Bud-vd2xd 2 жыл бұрын

Nice video as always, very good content. Is this the coloured render like Weber?

@PlasteringForBeginners 2 жыл бұрын

Cheers pal. And no, K-Rend is a Monocouche render system…totally different but still very popular. Hope this helps and thanks for watching 👍

@warrenconroy6523 2 жыл бұрын

You should be putting the first coat on with a tiling toothed trowel and pushing the mesh in with the teeth before smoothing it off. One or two run's over with the 1200 speed skim works great.

@Rendervate 2 жыл бұрын

Great content on Blaine’s page, you are a legend of the KZfaq plastering. Couple of things though not correct man, you can’t put the beads on with a grip they have to be embedded. You should use starcontact to do this. Also the plastering scrim won’t do anything, the gaps is good to allow for movement. Should of defo doubled up around the window stress points. Just a couple of things to do differently. Putting the finish on by hand alone though that’s great going haha. I wouldn’t man. All in all love your channel, I’m a advocate for educating people. Respect Joel

@PlasteringForBeginners 2 жыл бұрын

Thanks mate! I really appreciate that and thanks for the pointers. I did the extra mesh around the windows to be fair but stupidly didn’t film it. Thanks again for the tips and thanks for watching. Hope your channel is going well…keep it up Joel 👍👍

@TheOlzee Жыл бұрын

Can those float tools be used after I patch up a few areas on an textured wall to get that same effect? Or does the compound make a difference? I just use Toupret masonry filler

@kendodd8734 2 жыл бұрын

Top demo again mate u make it look easy but as we all know it ain’t but that said with ur vids it’s getting easier not in ur league though not by a long shot mate uve forgotten more about spreading than I know

@PlasteringForBeginners 2 жыл бұрын

Thank you mate. I really appreciate that. And I’m still learning all the time - I’m not there yet ha!

@katsucurry9420 2 жыл бұрын

Used silicone render thin coat system alot, I always water it down quite alot. Reason why yours is clumping is because your putting it on too thick. Widen your strokes to spread it really tight.. Also we don't use primer. Never had a problem on hundreds of jobs

@anthonyconti9626 2 жыл бұрын

Never had a go ! But would like to try it ! Would it take a kid kicking a football at it ? 🤔 and how much a sq meter on materials ? I might convince a customer at some point just to have a go ! 😎👌 Nice work as usual Blain 👌

@idealmethod 2 жыл бұрын

Thanks again for your videos my wall is still standing ! cheers mate, keep up the good work

@PlasteringForBeginners 2 жыл бұрын

Thanks for watching and well done! You should be proud!

@mattpurchase1 3 ай бұрын

Think you could you use webber adhesive render and then weber one coat as a finish ready for paint?

@ep91monster 2 жыл бұрын

Another cracking video mate 👍🏻. I'm considering attempting a silicone render on my garden room I'm building atm. Original plan was to cedral clad it, but with the prices of the cladding going through the roof atm, I'm considering giving silicone render a first go. Done plenty of s&c but because its timber framed, plus it needs the fibre cement fire rating to keep BC happy as there involved, i thought i might give it a go. Have you only ever used this particular brand? I'm down South so I'll see if i can find this gear locally if you reckon its a good one to go with. I'll throw the sts boards up too like you. Solely because there easily available from Wickes lol

@PlasteringForBeginners 2 жыл бұрын

Thanks mate. And if you’ve done sand cement then this will be child’s play pal ha! It’s very nice to work so I’d give it a go. I think you’d like it 👍

@ep91monster 2 жыл бұрын

@@PlasteringForBeginners I'll give it a go mate. Always liked the look of silicones, just never tried them. Keep smashing out the top work and content 😎👍🏻

@PlasteringForBeginners 2 жыл бұрын

Good luck my friend and thanks for watching!

@mattb9057 Жыл бұрын

Just a quick 1 mate love ya vids can u silicone render over silicone render

@nowyouareoneofus9684 Жыл бұрын

How do you make the edge from render to brick on the same wall?

@johnnybrown7644 2 жыл бұрын

Would like to see your take on krend blane. That tackle us unforgiving

@PlasteringForBeginners 2 жыл бұрын

I’ve tried it once but never since mate. Is it tough to work with then??

@greggyboy28 Жыл бұрын

Are you supposed to leave a vent at the top and bottom to allow airflow between the battens beneath the boards? I’m struggling to find the correct ones

@terryfincham7252 Жыл бұрын

Hello, are these renders ok for celcon block walls or would it be best to board wall first

@twillum Жыл бұрын

can you use this product on a non timber frame and cement board (block work for example)? Brilliant video again.

@PlasteringForBeginners Жыл бұрын

You can mate - you just have to use a different base coat. I think you can use KZP for the base with brick work 👍

@suzannekelly8606 Жыл бұрын

Would this work to smarten up some wooden raised beds in the garden?

@danmeadowcroft6621 3 ай бұрын

Hi, I've only used Johnstone's thin coat, you have to use their same colour primer, do you not need the same colour primer with this stuff? Cheers

@andrewbrown9327 8 ай бұрын

It's called sandcote in Australia and we put colour in it.

@Gandalf4137 2 жыл бұрын

Hi there, Blaine. Great work! Do you usually apply 2 coats of the base coat? Thank you.

@PlasteringForBeginners 2 жыл бұрын

You don’t have to…as long as the mesh is well bedded, walls are flat and the beads are covered then you’re all good.

@sinanylmaz5360 Жыл бұрын

What is called that materials you applying before mesh is it sand and cement or something ready to mixed ? Thank you

@johnclowes3894 Жыл бұрын

Would it be ok to use other sealers such as Uni bond or SBS

@abdulhakim-ali5215 Жыл бұрын

hello you have previously mentioned monocouche is not good. this is also silicone render. will the staining issue happen on this as well?

@wrighty6631 Жыл бұрын

Ive just had and i mean just was finished last Friday 6ft high brick wall built but its that bad I think I need to get it rendered as be to expensive to knock down and start again so whats best render to use over new bricks

@greggyboy28 Жыл бұрын

What do you use at the bottom to allow for ventilation and to prevent rodents/insects. I can’t seem to find the right stuff anywhere!

@clintforbes1856 10 ай бұрын

Do you think you could lay on and float up a full gable end, with a double extension, and a single off that, on your own? If not, would two people do? Or more people again, as you’re working off different levels on the scaffolding? Love the videos fella.

@PlasteringForBeginners 10 ай бұрын

Yeah mate. It’s nice stuff to use and it’s really quite fast. But it’s better with 2 people…it’s better that way. But 2 people can definitely do it pal 👍

@eaminslim52 2 жыл бұрын

Im actually looking to achieve this kind of finish on an internal, anyone see any issues with doing this? In terms of mositure etc?

@rebeccasummerhill4905 3 ай бұрын

Specifications for cement board is hpx base

@waynejordan1409 2 жыл бұрын

Hi Blaine, I have a new block garden wall I want to render would I use a silicone render on that? Cheers! Great video again 👍🏻

@shaunproctor922 Жыл бұрын

Could you use that to render over pebble dash?

@zeffmarlowe7926 2 жыл бұрын

Great video again. We’re doing a project and need to render an old solid brick wall with no damp treatment. The render needs to breath and cover some pretty uneven old walls. Silicon render has been recommended to us but I’m just wondering how well it works at covering uneven surfaces? Have you any experience with it like that?

@sean550 2 жыл бұрын

Hi..hope to use this shortly ..you put on two scratch coats..floated second scratch when dried apply sealer and then finish coat. Is that correct...thanks

@nigelsmith1198 2 жыл бұрын

@@sean550 normally the base coat is done in one hit and smoothed 6-10mm max, I do know plasterers that do a scratch coat followed by a tight final coat.

@sean550 2 жыл бұрын

@@nigelsmith1198 thanks..I assume the sealer goes on after scratch..

@nigelsmith1198 2 жыл бұрын

@@sean550 normally a sealer before the base coat then a primer before the final coat ( you get the primer mixed to the same colour as the finished coat)…. Good luck 👍

@blakeevans2963 2 жыл бұрын

If the render needs to breathe personally I'd recommend a breathable render like vpi or along them lines that's you would use for a lime substrate.. Unless you batton it out etc... Just my 5 pence worth do with it as you will. 👍

@delbut2 22 күн бұрын

How would you manage to get a sharp finish on non-90 degree angle/corners? I have a conservatory project where ive blocked-up the walls and it's corners are 135 degrees. I'd like to board a section and render around the remaining windows with the rest being timber cladding.

@mikehawkins5815 Жыл бұрын

Do you have to wait for first coat to dry before second coat? Also what's the name of the product you use?

@heartman3380 Жыл бұрын

I have a ragged bottom to my house where pebbledash has come away after digging out ground. What can i use to match the building, tried cement, it's too dark? any help is so needed and appreciated

@glennedwards5 2 жыл бұрын

Sorry if i've missed it but what is the name of the top coat?

@bartdrozdek3356 2 жыл бұрын

I've got pretty much the same set up going (timber frame, house wrap, battens & STS board) My question is since I checked the render manufacturer recommendations and they call for 14 day wait after base coat. What do you think? I kinda get that typically manufacturers will cover them selves and always recommend the extra. Thanks for the great video 👍🏻

@CamberKitesurfing Жыл бұрын

yeah i heard that too, all though I can't quite see any benefit, did you check it out?

@kf5541 2 жыл бұрын

Is the underside of the drip exposed?

@paulbrown3870 Жыл бұрын

I've used it for my shower wall but didn't use any primer between coats. Is this ok?

@rockgsxr 2 ай бұрын

you floated up the base coat? tell me more about this, are you still doing it that way, it seems alot of extra work, can i not just speedskim the basecoat/

@btendanhiggins5429 Жыл бұрын

Where do I get the flexi Trowell from actually what is the Trowell you are finishing top coat with