Maraming slamat..

Naikabit naman Po namin Lahat kapatid kaya nagawa namin.. diskarte lang kailangan.

I regretted so bad when I purchased this type of sheets

Totally agree with you I'm in the same situation 15 ft long panels by 4 ft wide 20 ft in the air with a section slope I did three panels by myself don't ask me how I have no idea but with another person and two ladders it's a lot easier and I used to heck of a lot of WD40 to slide it in the track still haven't figured out a way to get it in the track while it's on the roof from the side could only do it from sliding from the beginning but when it pops out it's a goddamn nightmare to finish product is pretty nice I will admit but this design of these H tracks is pretty dumb and should be updated I'm sure all the other videos online have metal connectors which make it look so much easier than trying to slide a 15 ft long panel on a 6-in slope in the air without it falling out right

My very very first saw when my neighbor asked me to do it for him and I lied and said yeah I can do it was to connect them all like in this video and then slide them up the roof together but then there would be no way to attach them to the wood beams because you have to get in between the panels to screw it down so that idea was out the window and I had to do one at a time because I couldn't go on top of the roof it wouldn't hold my weight but yeah it's all done now and now I know that I never really want to do it again unless I have extra people to hold it up on the other end other than that it was okay and those tracks are a nightmare I tell you the first one I thought was for a couple hours because I had it upside down thinking the long Edge was on the top yeah then I finally figured out it was upside down and went a little bit better but yeah lots of WD40 I know your posts are pretty old but I just did this yesterday so I wanted to say you're not the only one out there hating on this stuff but I got paid 400 bucks for doing it so whatever oh yeah and don't forget to wear gloves because when you try to slide it above your head with no gloves it will slice the heck out of the sides of your fingers another thing I did not know

You have to install the other sheet on top of it and it looks so bad

It just only a dust..

Yes boss oo pwede...

Ang installation sa PC kapatid depende sa lawang o sukat ng paglalagyan..Mura lang yung H connector ang PC ang mahal..

Yes pwede po

Meron cguro..try mo lang..

Sa hardware lang boss sa mga may benta ng polycarbonate

He isn't using two-piece snap profiles.

This type doesn't have 2 pieces, I regretted so bad when I purchased this h channel it's sucks so bad and is very hard to install by yourself

Hello

Hello...yes pwede mabend Yan dahil plastic lang Naman Yan..ngunit depende sa paglalagyan mo..pero Kung SQUARE Ang paggagamitan mo, kailangan mo na magcutting tapos Yung mga dugtungan lagyan mo Ng silicon Yung ginagamit sa pagkabit ng salamin..

Hello Kapatid.. appreciate ko Ang Yung pagcomment at pagtatanong...Ang H-connector kasi ay nakadesign talaga para lang sa polycarb..pero maari mong gamitin sa acrylic sheets..Kung maluwang lagyan mo Ng clear silicon para kumapit Yung sheets at di pasukin Ng tubig.🤗🤗🤗

@@JMN835 salamat po sa mabilis na reply! balak ko po kasi gawing divider yung acrylic sheets (mala-pader po talaga) para madivide ko po yung area na e-airconan para makatipid po sa kuryente... may kalakihan nga lang po, kaya kailangan pag dugtong dugtungin.. kulang kulang 3 meters po yung taas ng ceiling tapos mga 5 meters po yung haba ng wall... pano po kaya diskarte sa ganon? salamat po ulit!

Pwede Rin ganito gamit qa metal furring tapos rebits mo nlng Yung acrylic sheets

Pwede Rin aluminum frame

Yung pinakamalapad Ang sa ibabaw lodz

Salamat lOds

Search nio sa Fb TAs messenger din Bhobotnebres