That one is the 120 volt AC one. I have a 230 volt one in my shop. Both are PowMr so far so good. I am very happy with the performance. They both run 24/7.

@@kevincrawford2027 oh ok yes I have the all white 24v 3000w PowMr POW-LVM3.0K model mines run 24/7 as well I'm thinking about grabbing another one my self...

2 panels in series each panel 38.2 volts open circuit.

I HAVE TOO

you can use a light bulb.

I have mine set at cv 27.8 & fv 27.4 been working fine for about 8 months now.

Thanks

Redodo writes in manual cv28.8-29.2.you put lower voltage because is pwm and not mppt?thanks

No

@@kevincrawford2027 ok. Grazie

Why were you asking " do you have a UPS near your PC at home?" This system is an UPS. just much bigger than ones people usually have near their computers. On that note. I have used bigger batteries on the older model UPS ,which are not usually pure sine wave, the ones that people usually have near their computers. bUT those kind have very little charging power, only float.

Not sure what you have. What voltage is the inverter? What voltage are your solar panels? What are your inverter setting SBU, USB, OR SUB ? Knowing these may help get you started.

@@kevincrawford2027 I have the Pow Mr 3200 kvw solar panel is 275 w I have 10 total 275 w I have the setting on use open circuit voltage 41.81 v max Polycrystalline Solar Panels solar setting use have a 24 volt 200AH 1 ONLY THE CUE SETTING ON NO 16 SETTING WILL NOT STAY THERE KEEPS MOVING SOLAR NEVER WORKED FROM DAY ONE I BEEN ON IT 6 DAYS NOW NOT WORKING ONLY FROM GRID OR BATTERY. BY BATTERY IS LIFEPO4 PHOSPHATE IRON. I THINK I GOT THE WRONG INVERTER THE INVERTER IN FOR LITHIUM ION SETTING HAVE NO LITHIUM I WENT FOR THE CHEAP INVERTER AND THIS WHY I AM HAVEING TROBLE THIS ONE NOT FOR LIFEPO4 I HAVE TRID EVERYTHING EVERY SETTING YOU CAN THINK OF.

@@runneryg Here is what have set on mine. These are the ones that may help you get it working then you can can go through the other setting to your liking. Setting #01 SBU, #05 USE this is what you would use for LiFePo4, #16 CSO, #26 constant voltage 27.6, #27 27.0 float voltage. Hope this helps.

Wind mill, water wheel, controls both have dump loads when battery is full and another group of solar panels. All fused at both ends and both pos. and neg. side Good share of that has been redone since this video. I am now running a 48 volt system.

I have two identical sets of solar panels one hooked to the hybrid inverter and the other hooked directly to the battery by way of a sperate charge controller.. I have an external amp meter for the hybrid inverter. Using that they both are almost identical as far as charging amps. I think the display on the hybrid inverter show's the charging amps going to the battery minus the current used to run the inverter. In low sun conditions there might not be enough extra to charge the battery. I have noticed that the internal charge controller does taper off quicker than the external charge controller. I think that may be due to being an all in one with no external voltage loss associated with an external controller. Just my thoughts. I have no complaint so far on my hybrid inverter.

@@kevincrawford2027 Oh ok see I have the that all white all in one square looking PowMr 24v 3000w 40a/60a Mppt inverter/charger 120v ac along side with two Victron 30/100a Bluetooth charge controllers they be up to 70-80 watts before my PowMr see one watt they start charging soon after the sun come up but nothing from the power mister it's a green blinking light with no charging to the battery or incoming Watts till about 9:30 maybe 10:00 the victron start soon as the sun come up

This inverter has mppt range 90-400v, so it doesnt charge your battery at 30v.

@@curious-man No its PWM and max of 80 volts.