PRL High Volume Intake for the TYPE R / S install | Stock vs Spoon vs PRL Sound Comparison

PRL High Volume Intake for the TYPE R / S install | Stock vs Spoon vs PRL Sound Comparison | FL5 DE5

Рет қаралды 4,127

Күн бұрын

In this video we take a look at the PRL Intake for the 2024 Acura Integra Type S and 2024 Civic Type R.
I also do some sound comparison between stock, sprint/spoon and the intake itself.
Going from stock, you will instantly hear the difference!
0:00 Introduction
0:26 Unboxing
3:46 Installing Tips
6:30 Sound Comparison
8:24 Final Thoughts

Пікірлер: 36

@JohnNguyenVincent 2 ай бұрын

Sound comparison @6:30

@Jay-zd7vp 2 ай бұрын

Sounds amazing, thanks for the content

@JohnNguyenVincent 2 ай бұрын

Glad you enjoy it!

@matthewvondrus1505 Ай бұрын

Good sounds comparison. Thank you!

@JohnNguyenVincent Ай бұрын

My pleasure!

@roberteaston1552 15 күн бұрын

Any issues with the snorkel driving in the rain?

@lgjg7441 2 ай бұрын

So many more pops with the Sprint filter, that's crazy

@JohnNguyenVincent 2 ай бұрын

The first initial revs was only at 3 bars on the left. So it wasn’t hot enough where it started to burble. That was my bad!

@Carfanatic916 2 ай бұрын

I don’t know if it’s just me but I feel the ITS with a sprint filter produces more sound than the FL5. That or your camera and mic set up is really good lol. I have watch other videos and yours just comes out with more turbo noise. Anyways yes it is a tad bit louder than the sprint filter you had on previously. Would have been nice if PRL had a carb sticker for us Cali boys though.

@JohnNguyenVincent 2 ай бұрын

I put the sprint filter on the FL5 and it sounds similar. So it’s probably just the video. And Yeah, I used the same mic on both of my test just hoping it didn’t auto some of the sensitivity up or down.

@thefamilychannelATL 28 күн бұрын

Is that a garage padding on the floor? If so where did you order it from ?

@JohnNguyenVincent 25 күн бұрын

swisstrax!

@A_guan 2 ай бұрын

For the maf sensor harness, what did you mean by removing one of the pins? Is it like a clip you remove that frees it up? I might go that route if it's easier to do. I could care less if that plastic stays on. Also I heard you had to take out the ecu, is there anything else electrical other then maf sensor and the 2 connectors on the top of the ecu that you need to unplug? Lastly, the piece you mentioned at 5:20...all I need to do is loosen the 2 big clamps and then I can just slide that hose out with force/without unscrewing that clamp if it was even possible?

@JohnNguyenVincent 2 ай бұрын

If you remove the clips, it will free up the space a bit, just use a small flat head on it and pry it out. There is like 20 clips and they are tiny and space closely together. For the plugs, there are more plugs under the ecu that you need to be relocate. Underneath the ecu, you have to remove a bracket (that bracket holds like two plugs). and lastly, yeah that three hole coupler (tripler? lol), is not super tight where you can just slide it off. Just slide it off without even touching the small clip.

@A_guan 2 ай бұрын

@@JohnNguyenVincent you didn't remove the 20 clips right? You just removed one and it was enough if I remember right? The plugs under there you won't need to unplug or something do you?

@JohnNguyenVincent 2 ай бұрын

you don't need necessarily need to unplug the harness below the ecu section but you need to unclip them and relocate them to the new spot. The second intake duct is there now @@A_guan

@A_guan 2 ай бұрын

@@JohnNguyenVincent ahhh okay that I can deal with I just hate messing with electrical. Never in my life did I ever expect to take out the ecu to install an intake but looks straight forward enough. More annoying part seems to be that maf harness at this point since ecu is just 2 bolts and undoing those connectors

@JohnNguyenVincent 2 ай бұрын

I went back and redid the harness loom

@mgj605 2 ай бұрын

Can you share a link where you got the spoon/sprint drop in filter for the ITS?

@JohnNguyenVincent 2 ай бұрын

got it from madnessautoworks

@JohnNguyenVincent 2 ай бұрын

madnessautoworks.com/index.php?route=product/product&product_id=300014922

@AcuraintegratypeS 2 ай бұрын

Can I buy your other filter you had in your vehicle? I don't know if it's spoon filter I'll pay for shipping.

@JohnNguyenVincent 2 ай бұрын

Sold already sorry!

@commonduck10 2 ай бұрын

Tune made it very noticeable faster?

@JohnNguyenVincent 2 ай бұрын

I should have my video on coming soon. Short answer yes!

@commonduck10 2 ай бұрын

@@JohnNguyenVincent I just sent my ecu to phearable, so I’m anxious…type s

@w.o.t6584 2 ай бұрын

Did you have to remove the ecu to instal the "snorkel"?

@JohnNguyenVincent 2 ай бұрын

Yeah it’s required for the snorkel

@w.o.t6584 2 ай бұрын

Difficult to do?

@JohnNguyenVincent 2 ай бұрын

@@w.o.t6584 the most technical part is removing the harness from the clips. It’s not hard but I can see that part can get bad real if it doesn’t go in properly.

@xXYellowFlashXx Ай бұрын

Apparently I read somewhere u don’t have to take off the ecu just unbolt it I believe

@JohnNguyenVincent Ай бұрын

@@xXYellowFlashXx I can only imagine that it will be more cramped and more difficult if you don't unplug it but probably possible.