Love the wood accent wall…we really enjoy your videos.😊

Just subbed to your channel, you built your building/work shop & I did watch all the videos you made. The rough cut lumber on one back wall is exactly what I am going for also. Great accent when you walk into your shop. You are reading my mind, one this one.

**Take the industrial cover off your quad 4s receptacle box and install a 1" deep p-ring, mount the two receptacles, then use a jumbo flush cover. That should cover up your miter cuts in the board.**

Hey Bro Made a Awesome look. I would be very pleased with it . Good job again. Thanks. Craig Pa

Man that looks goooood. I've been wanting to do something like this to my man cave. Not needing the moisture barrier would make it a lot simpler I think. Might have to go for it. Very inspirational!

Great job!!!

Very nice!

Thanks for the video. I like the vertical boards. I have a 24x48 metal building which is a garage/apartment/shop. It was built 20 years ago. It is metal purlin with metal siding and roof with sprayed in insulation. We live in Texas and the insulation seems to be good for our area. Framing with wood studs in the wall has been “fun”. Your idea looks easier. I have a few walls or portions done with wood studs screwed into the metal purlins with similar screws to what you used. Then nailing or screwing the 4x8 OSB onto those studs. In some places I screw the OSB right into meta purlin around a window. Anyway I am on a mission to organize my shop and need more walls to hang stuff from. I can hang things quite easily on wood. Again, thanks for the video. You have a great helper there. Mine are all in their 30’s now.

Man that looks great brother!

love the shop and trans am in the background

Beautiful Trans Am!!

Looks so good! Nicely done.

For the electrical, I would have removed the industrial covers and just gone with standard surface mount covers (like what is inside your house). Could either be plastic or metal surface covers depending on what you wanted. The 4 square box would need to be raised so the edge of the box is at the surface of the wood.

Looks Good 👍🏾

Thanks, with the info you have provided, I'll just stick frame my garage.

That’s a good job insulating the walls.

That looks amazing. I will definitely be doing something similar. Keep posting the garage updates.

Looks great! I would have burned them for an extra rustic it also burns off any mold or bugs

I'm doing this staring today. Using 1x6 10ft pine.

turned out beautifuli just got a 20x26 garage and looking for ideas

Great video. I just had a metal garage built, and I elected to do the double-bubble wrap to keep the moisture out. Since you caulked the outside, where is the moisture going to go during weather changes? The felt paper will keep it out from the inside, but the area between the felt paper and the metal siding will still create condensation, where will tghe condensation go? What am I missing here?

Yeah I got an 18 by 30 carport and I get what you're saying when it's cold out it's fine but if the weather changes real fast from how to warm the metal will sweat and it will just basically rain on the inside of your shop one thing is I wish I would have been told is that they have moisture resistant barrier stuff that you can have put down before they put the metal if I ever have a shop done it will have all that done before they even put the metal on because we're looking to buy a house and I want to build a shop like kind of what you did

Looking good! (Although I’m only 5 minutes in). Very first thing I would put in my garage is speakers w/ stereo equipment. Gotta have music to work with

Looks good man, i definitely would of installed reflective insulation under metal siding . Fyi mold will go away if its closed up. Needs air and multiple treatments. Also i would keep wood up at least 1 inch off concrete floor.

When your ‘project manager’ suggests ice cream for lunch… “Yes, please!”

I like your thought processes, there's a bunch of different ways to finish a wall and your idea will be a good solid experiment. While you had the 45's off you might have thought to paint them black or something so they disappear. Still something to be proud of and multipurpose (backdrop, functional tool hanging, KZfaq content, draft barrier, critter barrier, better acoustics).

Nice work, but Bleach does not kill all mold, only about 2% of molds. Vinegar is a better option as it kills 99% of all molds.

Hey.... what happened to Ep.10?... lol. I went looking for it and couldn't find it. Loving this garage build series - thanks for sharing it with us.

So I saw your video where you fired the building erector. Can’t find a follow up video to that. Curious how you resolved the issue. From subsequent videos, looks like you have the same building still.

perfect, just what i was looking for. what did you use on slab under 1x4 and is it PT? What screws did you use for 1x4? Construction adhesive or just caulk under 1x4?

About an inch of closed foam is the way to go before the wood. The foam will add rigidity and strength actually. The foam you sprayed may not be closed and over time might affect metal.You could skip the felt after a layer of closed foam and allow ventilation. You don’t want mold forming. Mold is dangerous.

Mike the wall looks really good! I might look really nice to at least do the right & left walls as well!

Find the center of your nailers and snap a line so that your nails are centered and uniform

Would you do this to the four walls or would it potentially weaken the structure too much?

Nicely done, don't forget to trim out the windows.

Would have foam boarded the metal before adding the walls.

The 1x4 in the middle screwed against the metal horizontally.. why did you screw it on leaving like over half the metal beam exposed? Was it necessary to be that height for some reason?

Can't find what screws you were using. I have been using the Teks wood to metal screws and they are a bear to put in. Yours looked like Teks but with a coarse thread. Yours go in way easier.

2 years in how is it holding up? Can you explain how the load is transferred by doing the boards that way?

Nice but superfluous

I know this comment is late, but the most dad thing I've seen is when your son gave you the pen, and you set it back down, hahaha

Should have gotten closed cell foam. Fully sealed, no condensation issues, and it greatly increases the entire buildings rigidness.

Good move

8:42 You should replace that 'RS' (raised surface) cover mounted on the quad with a deep two-gang mud-ring...learn how to 'measure twice, cut once'.

Hey man I’m ping something similar in my building. On the electric boxes did you mount them on top of the metal framing or flush with them? Thanks

Man that’s a Great Job!!!! I love the look of the wood wall. I’m building my new 20x25 in a few weeks. I plan on putting silicone caulk down under the metal frame base and spray foam on all the gaps. I’m having 2” roll fiberglass insulation installed and want to finish the interior like yours with the wood. I’m just curious what’s with the ratchet straps?

French cleats would be cool

Man that's nice. What's the black tarp that u put up. Is it a moisture barrier

How has it done with the cold temp? I’m trying to figure out the insulation deal now myself. I’m leaning toward foam board but had to ask how your method is working.

No insulation?

Is your wood source for the barn wood near pendleton? Would like to do the same thing in my shop

i dig the wall!! im about to put a wall in my shop! i might follow your lead!

Those boards werent stickered correctly after cutting. If they were there would be no mold

Woodglut is nice for that.

For this I would have sealed everything with OSI rather than foam...

Not sure if it was smart to seal up bottom because if there is moisture then where does it go or drain too!

Is that old barn wood

I think you've made a huge mistake sealing the metal and leaving an open cavity. Love the work ethics!

Woodglut has a lot of designs to choose from.

The first thing to hang on your wall is your stars and stripes flag yeah? I am an English viewer. How about spraying those mouldy planks with bleach to see if it cleans them up. Nice work by the way.

Thousands of lifetime projects with Woodglut plans.

I hope the circular saw near your son, while on the wood pile, does not have a battery in it.

So dangerous😢😢😢😢😢😢😢

Why were some people so hard on you? Obviously theyve never gotten shafted by a contractor, happens alot. And to me too. The world stinks anymore, theyll understand when it happens to them😢

Wow beautiful work dude. My thought tho. A tubular steel frame building is not at all ment for quality and craftsmanship. So unless you put every screw in. Might think about continuing to throw money at it. They look awesome from the road. But flying around in a tornado is kinda scary. Far as water penetration prevention. Um. Go outside. If your only sealing the inside. It’s too late. The water is doing it’s best. It’ll leak warp pop and sound like popcorn on a warm day. Dang bruh. For what it’s worth I’m sorry. But the work looks great. Just need to back up to the beginning. “Steel frame” refers to gerders and beams and pearlings. Good thick metal. Those buildings usually get standing seam. Heavy thick good quality. You just got a big erector set. Add more of everything. There’s never implied quality at eagle carports. O wow you even put the vapor barrier inside. What do you get paid to do on a regular day? Surely not contracting and thinking up your own ideas? Maybe a jobsite foreman. ? You know enough to sell it. But please don’t sell your ideas as facts. I’m stopping at 4 minutes. This hurts my wallet and efficiency. Wait about 6 years before saying I’m wrong. Water works slowly.

STAY OFF THE TWO WHEELS FOR YOUR KIDS SAKE. good grief.

Yea, now you added a real problem. Mold.

This book is a comprehensive guide for anyone who wants to create various types of garden buildings. The book provides clear and detailed instructions with numerous photos. kzfaq.infoUgkxBE-xSmFU7PIaMFUmmhnFxE035s5svtxeAs a novice, I appreciated the book's step-by-step approach to the basics of building. The book also appeals to the more advanced DIY enthusiast with projects ranging from simple to complex. The book is up to date with the latest trends, such as solar panels, green roofs, and sweet chestnut shakes. The book has inspired me to pursue more projects in the future.