QRM eliminator is one of the best things for QRM it is by far the best piece of kit I have ever bought for my shack.
Пікірлер: 26
@stuartmcloughlin8 ай бұрын
The single most important element in this is having a good receive antenna for the QRM eliminator. And secondly, knowing what the source of noise is. They certainly work - without question they do and can be the difference between being able to use the band - or not as the case may be.
@juscelinorocha2475 ай бұрын
a $3000 radio and they still haven't made a decent NB.
@radioman64895 ай бұрын
Two nice rigs
@hamradiostationg0dtx5835 ай бұрын
Thank you
@g0pvr110 ай бұрын
Well you know what i think of them john, ( Witchcraft) you have the best model to, with lights on tx and rx!
@johnm0csn11 ай бұрын
Looking Good Jb...I need to do a new episode. This weekend I might get chance...Sterling job pal keep em coming...CSN
@hamradiostationg0dtx58311 ай бұрын
Thanks john
@samuelwalton89648 ай бұрын
What is opinion on the FTDX-101MP, mainly the V-Tune and roofing filters for added quality of noise reduction and additionally the 200 watts, dual tuner and power supply speaker add to a better experience? If the V-Tune and roofing filters are not as helpful for added ease of hearing then the FTDX10 maybe the best choice?
@hamradiostationg0dtx5837 ай бұрын
Sorry i,v got a ftdx101d but the vc tune is fab
@johnratcliffe64389 ай бұрын
I don't need Amp 1 on 20m. I find it far too noisy. My own approach is to roll back RF gain to the point the meter just deflects on signals very slightly, then IPO1 and DNR. I use an FTDX5000MP, but the principle is the same.
@g0pvr110 ай бұрын
I have put a link to ali express, only place at present to get the latest model with tx and rx indicator’s. U need this!! I have 2 !!
@aarontooth9 ай бұрын
So is a "QRM eliminator" any different than a directional antenna? I get the general idea of feeding in a second antenna and adjusting its phase to cancel noise. But that's just a phased array antenna, essentially just a directional antenna. You could also use, for eg, a Yagi, couldn't you? Or is this a way of making your array adjustable? By the way, I don't think you should be aiming for "no noise" on the waterfall. All that's doing is showing your radio/antenna are deaf. If you're on HF, there should be lots of noise, all the time. The point is the SNR should be good, and you should have lots of faint signals.
@hamradiostationg0dtx5839 ай бұрын
Adjustable phasing network to cancel out local QRM.
@84rafaelkld5 ай бұрын
Hola. Gracias por su vídeo. Qué dipolo (medidas) como antena auxiliar usa para una mejor eficacia? Gracias.
@hamradiostationg0dtx5835 ай бұрын
19.812 metres END FEED WIRE 65 FT
@kylefreemason10 ай бұрын
Can you do a video about how you tune the qrm eliminator?
@hamradiostationg0dtx58310 ай бұрын
Hi Kyle i did a video a few months ago {tuning the qrm eliminator part 2} hope you find it helpful.
@kylefreemason10 ай бұрын
@@hamradiostationg0dtx583 Guess I missed it, ty for the heads up.
@charlescassidy14964 ай бұрын
Great video! de W2CSI
@user-pe1ff1cg6i9 ай бұрын
Hi ... can you do a video with SNR measurements on a weak signal using one of these boxes ? I have and the results are not good ! , I noticed that your signals adacent to the qrm were attenuated when you turned the eliminator on, some were not visible after turning it on , actually only 1 was visible they other disappeared ! ... actual measurements would be good as to see whether they severly attenuate primary signals as well , possibly getting worst SNR results than without the box ... iam still up in the air as to whether your really gain an advantage with these eliminators or its just because the qrm has attenuated, the box works in the mind ? ... the DNR in the 101d with its preset Algorithms seems a better way to go as they, dont ,attenuate the primary signal whatsoever .. aditionally , only wished Yaesu in its firmware upgrades add to its algorithms to even better results .... The DNR is a game changer in this field
@hamradiostationg0dtx5839 ай бұрын
HI to answer your question if you are using a radio to get rid of qrm you use the att rf gain noise reduction dnr shift with notch and cont in my situation the noise is coming from solar panels on a neighbours house so the noise is to great for the radio to cope . This is the problem with man made noise, no matter what you do with the radio the qrm maybe to strong such as power line noise. So to answer your question using a qrm eliminator will attenuate your signal but so would your radio if you were trying to get rid of the noise. The goal is to get rid of qrm so you can hear the signal below the noise floor. It is irrelevent what s reading you get the goal is to hear the station. Hope this has been some help. G0DTX
@willytee58510 ай бұрын
Are you able to tx QRO using this ?
@hamradiostationg0dtx58310 ай бұрын
radio then qrm eliminator up to 100w then linear to the power you need.
@Ei2iP10 ай бұрын
At last some one who understand how to use ATT, the amount of people who run these radios wide open, just so that S meter reads S9.. Respect old man. You understand your radios. What is the antenna on your QRM Eliminator?