Quick Tip-Throttle Cleaning

Quick Tip-Throttle Cleaning - EricTheCarGuy

Рет қаралды 7,120,364

15 жыл бұрын

This one goes out to BowlingBallOut who posted a question about a sticky throttle on his Saturn. It was a great question so I decided to make this video in response to it. There are many different configurations of throttle assemblies but for the most part if you have a throttle that is sticking you might be able to fix it using the procedures in this video. I am aware you may not able to purchase spray throttle cleaner in some states now but I'm sure they have some alternative available at your local parts store.
One very important note here is that if you have a drive by wire throttle (DBW), then I do NOT recommend this procedure. If you perform this procedure on a DBW throttle body you may need to have the throttle reset in order to get your engine to idle or even start. I only recommend this procedure if you're trying to correct a problem with a sticking throttle.
If you have idle problems, I recommend you check out this article on my website.
www.ericthecarguy.com/faq/solv...
The best place for answers to your automotive questions: www.ericthecarguy.com
BowlingBalOutl's channel
/ bowlingballout
Facebook: EricTheCarGu...
Twitter: / ericthecarguy
Google+: plus.google.com/1001951801966...
Information on Premium Membership: www.ericthecarguy.com/premium...
Stay dirty
ETCG
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Пікірлер: 2 200

@salvatorespalato3503 3 жыл бұрын

Doing this stopped my car from stalling while coming to a stop. Best thing ever. 👍🏻🇦🇺

@crand20033 9 ай бұрын

If it is stalling you also need to clean your MAFS.

@therealboofighter 8 жыл бұрын

I don't have a red rag, will it still work with a blue rag?

@Lilpandabear98 8 жыл бұрын

Noo you need the red one

@therealboofighter 8 жыл бұрын

+Lilpandabear98 well too late now, used the blue rag and my trunk fell off and my tires over inflated. Yikes.

@Lilpandabear98 8 жыл бұрын

+boofighter damn hopefully the blue one fixeses that😉😂

@jessejaviangel 8 жыл бұрын

lmao

@kevinfrancois4624 8 жыл бұрын

lmao

@misterlove7034 6 жыл бұрын

Dang, they were gonna charge me close to 300 bucks at the dealership lol. Thanks for the video, man!

@Lana-em2cy 2 жыл бұрын

Literally, I love KZfaq fr

@daviddowns7552 Жыл бұрын

that is extreme.$ they wiped mine for zero$ at mechanics, i gave him the can of seafoam cleaner.crc maf sensor cleaner works good+ safely.

@reidbarnes9851 3 жыл бұрын

I just watched this video, 11 years later. Eric is just a little youngster ! I love the ETCG videos. Keep them coming Eric. They're vey helpful.

@mstielau 5 жыл бұрын

I appreciate very much the advice given in this video, and especially to those commenters who warned about not manually moving the butterfly valve on a drive-by-wire car, like my '03 Accord. I never would have known that could be harmful to it, so a big "thank you" to all who mentioned it!

@adamb84 Жыл бұрын

If your throttle body is opened by electricity than no don't move it manually, you your's is opened by the throttle cable than yes you can open the butterfly manually

@jinglejazz7537 8 жыл бұрын

HOWDY ERICTHECARGUY...I have a 92 crown vic lx, with 280,000kms on it. had the throttle sticking problem, didn't know what it was causing it to hesitate and even stall on the QE2 in Alberta. Saw your vid, man that throttle was completely covered in thick gunk, cleaned it out like you showed, and it works great now, now I have to change the belt, followed your instructions, another triumph, thanks eh!

@WhatchuFinnaDo421 11 жыл бұрын

Wow... Thank you. I've been wondering why my pedal was sticking for the last three years. Didn't think about looking at the throttle since it felt like the problem was the pedal sticking. Awesome advice.

@TIFFandDRETV 2 жыл бұрын

Great job Eric. On my 2004 Chevy Trailblazer, I replaced the MAP due to OBD code. My acceleration increase and overall performance was great. Two days later, I got a P0106 code (MAP performance). Cleaning the throttle body was one of the suggestions. In fact, cleaning the throttle body every 30,000 miles or so helps. I can't remember the last time I did this on my SUV (205,000). So I was looking for a video that shows how to clean the throttle body without removing it (I'm not as young as I used to be :)). Thanks again for a quick and concise video.

@nik12937 10 жыл бұрын

This is especially helpful and even important with newer drive-by-wire throttle bodies. Since they're actuated by a small motor or similar, and tend to be taking the place of idle air control valves and the like, they cause a lot of odd problems when sticking. One problem being stalling only when starting the car warm. The throttle will get stuck closed and starve the engine. It also tends to make throttle response feel even more delayed than most drive-by-wire throttles are from the factory. Great tip Eric!

@anthonykrine7403 12 жыл бұрын

Good video, the best product to use to clean out throttle bodies is the ThreeBond Engine Conditioner. Heat the engine to running temp first then turn off the engine and take the hose from the throttle body. Spray the engine conditioner into the throttle body and it will foam up and clean all gummed up areas. It also lubricates the throttle body. Start the engine and spray the rest of the can through and it will clean the complete combustion chamber. It is a complete carbon clean in a can.

@shannonnewcomb7742 4 жыл бұрын

Thanks Eric The Car Guy for your simple and informative video on throttle body cleaning.

@autumnrankin9240 7 жыл бұрын

DANG!!! That was the easiest snorkel removal ever. I was fighting with mine for a while. Thank you for posting this!!

@chrisnotap 11 жыл бұрын

Great videos Eric! My tip to you is to use a toothbrush instead of the rag. They do a great job and looks brand new when your finished. On fly by wire cars, make sure the ignition is off before moving the throttle plate.Also don't forget to use nitrile gloves when working to stop the skin from absorbing grease dirt and chemicals.

@mohammedwells1186 2 жыл бұрын

You all probably dont give a damn but does anybody know a method to log back into an instagram account?? I was stupid forgot the account password. I love any assistance you can give me.

@bronsontitus6298 2 жыл бұрын

@Mohammed Wells Instablaster :)

@mohammedwells1186 2 жыл бұрын

@Bronson Titus thanks for your reply. I found the site thru google and Im waiting for the hacking stuff atm. I see it takes quite some time so I will get back to you later when my account password hopefully is recovered.

@mohammedwells1186 2 жыл бұрын

@Bronson Titus it worked and I actually got access to my account again. I'm so happy:D Thank you so much you saved my account :D

@bronsontitus6298 2 жыл бұрын

@Mohammed Wells No problem :)

@sk88boarding 8 жыл бұрын

those side bruns are majestic

@guesswhomartin9249 7 жыл бұрын

those side burns... yuk... I guess, if you like them.

@Drillz007 7 жыл бұрын

how can you not like them

@guesswhomartin9249 7 жыл бұрын

That's fine .. You like them... Do your thing. I don't care for side burns..

@82_KID 7 жыл бұрын

What is a side brun?

@cemsengul16 7 жыл бұрын

1SlowAss96Ram yep if he became a mechanic

@scubbarookie 3 жыл бұрын

I like the throttle cleaner from CRC. They make great products! Thank you for this video and about the coating on certain throttle bodies. Take care.

@TheAutoDIYGuy 8 жыл бұрын

Hey Eric...excellent video once again! You've inspired me and others to start making videos, so much so that I made my first Push to Start Button Auto DIY Tutorial! Thanks so much for the inspiration, and keep doing what you're doing! You're great!

@VigilanteVegan 7 жыл бұрын

1:42 Throttle body has a smiley face as a way of saying "thank you for cleaning me."

@KINGMACON1 4 жыл бұрын

Macon 🤔

@albinobuck2449 8 жыл бұрын

Damn dude your videos are like crack, i was up all night, think i watched like 30 of em lol.. Good stuff bro!

@BlastReadingSeries 7 жыл бұрын

We've all been there...

@c-lospompa7376 4 жыл бұрын

Its good shit

@RichardSmith-ic1zw 4 жыл бұрын

Like cocaine

@saleemhoosen2236 4 жыл бұрын

Dude.. u sit and watch crack all night?

@DursunX 2 жыл бұрын

i noticed you've been away for a while.. that's a long time between binges

@bdcochran01 8 жыл бұрын

Thank you. I have a Toyota Avalon 2004 that had a sticking accelerator. I saw how you did it. I did it too. My car looked a bit different under the hood. I am an old guy who used to take out the carburetor and clean it 50 years ago. I didn't realize that the same type technology was in modern cars. I didn't even have to use a tooth brush to fix the problem. Thanks again.

@kendefilippo1680 10 жыл бұрын

Appreciate your straightforward directions and clear video on car care. Your piece on throttle body cleaning was especially helpful. Thanks much for your efforts!! You saved me big $$$. Owner: 2005 Mazda Tribute S V6 4 x 4 2007 Toyota Solara V6 Convertible KND Northern NJ

@BigWesLawns 9 жыл бұрын

Dude!you always have the best vids when I need. clear and helpful always!! peace.

@ericthecarguy 12 жыл бұрын

@MrMdezee If someone adjusted the idle screw I would recommend turning it back to where it was originally and then checking for vacuum leaks. If you suspect an IAC problem replace it, I haven't had any luck cleaning them.

@emma-gc7hr 10 жыл бұрын

You give me a lot of useful info. A big thank you to Mr, ERICtheCARguy. Explanation easy to understand theory & practical. Once again double thumbs up to you for your excellent presentation.

@davidadamus177 2 жыл бұрын

Thanks for the video! Had a check engine on my wife's Hyundai and it was the throttle body. Gave it a clean with the video (was my first time doing this) and the car runs great and check engine light is off. Thanks!

@gmtunerz 10 жыл бұрын

Hi Eric, your videos are awesome! I usually use Seafoam instead of TB cleaner and spray about 1/8 of a can in the intake as well. I leave it for about 10 minutes then start it up and let it run through. I've heard that this can actually plug your catalytic converter. I've also heard that it cleans the catalytic? What's your thought on this?

@lrjhnsn0731 10 жыл бұрын

I feel like I can do this myself now! Thank you!!!

@jeffcox2455 2 жыл бұрын

Thank God for this video, clear flood mode, never heard of that! Sure thing though, started up after a few seconds and a few trys of flooring the pedal. Thank you!

@HellaFlush070 7 жыл бұрын

2000 Honda Civic EK Just did this outside in like 25 mins time, cold air intake nuts n bolts.. Cleaned the inside as far as i could, sprayed with the throttle valve cleaner a honest amount... Started it with full throttle and the beast is back alive :D Big up Eric!! Pretty sure its because of the full throttle during start, sputtered out the excess n' bout to see if it made a difference!! Love the videos m8

@Th3P3ac3N33d3d 4 жыл бұрын

And the mechanic tried charging me 300 for this.. thank you so much brother

@lovemym16 8 жыл бұрын

i find a brick on the pedal helps keep the throttle plate open

@NotHarry-er3wg 6 жыл бұрын

I knew a Ford dealer that used to do this to Problem Lincoln and ford Mercury that were on the edge of warrantee because of bearing knock. Ford would call the noisy engine normal. Well was not normal after that ''' 80FNot so sure if it would work on this application thought although id would solve the throttle body issue. 8)

@JohnDoe-qq8et 5 жыл бұрын

I use the steering wheel lock.

@mustafaalmustafa3096 5 жыл бұрын

doesn't work on all cars'! I've tried it at my Lexus GS bot no chance!

@fabuloso3635 4 жыл бұрын

Where's the brick having a hard time looking for a brick on my petal

@suzumr2754 4 жыл бұрын

@@fabuloso3635 or you could use a long stick or a broom or something long, put it between the seat and the pedal, and move the seat colser to the steering wheel, all the while the long object will depress the pedal for you. This is one way.

@Crispy27 11 жыл бұрын

Video's much appreciated. I'm not exactly a car guy, and this helped me get the job done. For what it's worth, I live in NY and bought aerosol TB cleaner no problem.

@cagonzal13 3 жыл бұрын

Oldie but goodie always looking for my answers in your video library. Thanks Eric, Ive been subbed since geeze when you were in your garage.

@crkerriklein 8 жыл бұрын

damn, there's a lot of corrosion on those battery terminals

@williwonka5106 7 жыл бұрын

Sea Foam fuel system cleaner and a tooth brush works well. I always use an old toothbrush anyway.

@slickstretch6391 2 жыл бұрын

Thanks. I was wondering exactly that, because I have some Seafoam, but I don't have throttle cleaner.

@turnipsucks6416 Жыл бұрын

Timeless video. And here to do the job and see how to. Thank you Eric.

@n.r.9468 10 жыл бұрын

It worked like a charge you are a great teacher thanks, I had this problem after changing my serpentine belt and automatic tensioner and pulley idler which I also watch how to change from your channel my engine light even went off thanks again.

@Stealth170rl 9 жыл бұрын

HOLY CORRODED BATTERY TERMINAL BATMAN!!!

@BMACVAGS 10 жыл бұрын

Nice video

@turboeddude4849 Жыл бұрын

This is amazing video quality for 13 years ago.

@thedarkknight1971 6 ай бұрын

I've often used an old toothbrush to help clean small/hard to get areas in conjunction with various cleaners, it helps to remove the harder to clean debrits etc... 👍 😎

@chrisbyers4726 7 жыл бұрын

I would personally recommend removing the throttle body completely. I remove all electronics (IAC, TPS, etc..) and clean all the passages. The TB cleaner shouldn't damage the sensors and valves (IAC) but if I'm cleaning something I'm doing it 100%. Definitely pay attention to removing all the buildup around the edges of the butterfly valve, that's where it will stick the most. And don't use anything abrasive to clean internally, a nylon bristle brush is ok, NO steel wire!! Now if you are still having a problem with throttle response then I'd look at the throttle cable. Just like the hood latch cable it's braided wire that will stretch and when it's stretched the butterfly in the TB won't fully open. There are the cheap zip tie tricks, but just replace the cable, not worth a snapped cable at WOT!!

@beckyjustice7514 7 жыл бұрын

Really good advice! Thank u so much! My ,2091 dodge neon started stalling a month ago while! Usually after I drove it 15 miles it would stall and stutter a few times, then straiten back out And drove fine! It did that a few weeks then today while I was driving home it just died, while driving down the road, and won't start back now! It cranks but won't start! And I listened at the gas tank to see if the fuel pump kicks in when my friend turned the key over, the fuel pump came on and makes a whining noise! Do u no what can cause my car to stutter then die and not start back! Thank u so very much 😊😊

@beckyjustice7514 7 жыл бұрын

Sorry it's a 2001 dodge neon, and if it's the fuel filter can that be changed without changing the fuel pump! I heard the fuel filter was made in the pump and have to change the whole fuel pump! Thank u so much

@tanners.6524 7 жыл бұрын

Becky Justice Do you run your tank below 1/4 full often? More than likely your fuel pump is done for but you can try a filter first.

@beckyjustice7514 7 жыл бұрын

Thank u so much Tanner! I kinda had a feeling it might be the fuel pump! I went out the next morning and it started right up like nothing was ever wrong with it! But still has the stalling after driving 15 miles and still wants to quit when I come to a stop on inclines! And when I turn the key I can hear the fuel pump kicks on for a few seconds! Thank u so much for all your help Tanner! I really appreciate it

@indiabrown372 7 жыл бұрын

I love you so much for this, I just watched another video and he told me to take it completely off

@ericthecarguy 12 жыл бұрын

@tonytiger33 If you don't have a check engine light start with the basics like plugs and a fuel filter. DON'T start replacing sensors as they probably have nothing to do with it. You might also do a power balance test to see if you can find a particular cylinder that is at fault, I've done a video on this if that helps.

@shawndahl9734 Жыл бұрын

😢

@shawndahl9734 Жыл бұрын

❤ 1:20

@ryanhill7318 5 жыл бұрын

Great to have you back my man!! Great job as always

@3rdGenGuy 11 жыл бұрын

THX man! my 2005 Colorado had poor throttle response. but after i cleaned the massive amount of gunk on the butterfly, works great now.

@DustyKorpse 7 жыл бұрын

that's ok for mechanical throttles isn't it problematic for electronically controlled throttles to move them manually?

@nighthawk0077 6 жыл бұрын

Dusty Korpse Yes, read the description, he specifically states this procedure is for direct mechanical TBs and not be used for DBW or E-TBs

@paddywynne8049 6 жыл бұрын

Dusty Korpse just get someone to press accelerator pedal it will open

@billwilson6096 5 жыл бұрын

Paddy Wynne not so simple, it is electric and the motor must be running.

@trueplayaa111 4 жыл бұрын

@@billwilson6096 if you are cleaning your etb while its on say goodbye to your finger smh

@billwilson6096 4 жыл бұрын

krodie you sent your warning to the wrong B. W. I’ve learned over the years to be careful where I stick my fingers.

@NOBOX7 7 жыл бұрын

do not move the butterfly with your hand on modern cars , it will mes up the position censor calibration

@tobiasjn.pierre2655 7 жыл бұрын

NOBOX7 how do u move it to clean inside it

@NOBOX7 7 жыл бұрын

Tobias Jn. Pierre on new cars you turn the ignition on but dont start the car then have some body press the gas peddle and it will open . or you can remove the throttle body from the engine

@tobiasjn.pierre2655 7 жыл бұрын

Thank you, I remove it from the car today

@AutOdometer 7 жыл бұрын

nice tip

@WorethV12 7 жыл бұрын

Can I move it on a NB Miata ? Planning to clean it this weekend

@VigilanteVegan 7 жыл бұрын

I just used rubbing alcohol and Air Flow Sensor cleaner. And some Q-tips and paper towels. It's best to do it when you don't have to drive anywhere afterward that day. So do it at the end of the day and let your car sit overnight before starting so the chemicals can evaporate and throttle can air dry overnight. Otherwise you'll take a chance of trouble starting and/or the chemicals flowing your exhaust.

@whydoihave6neutrals772 4 жыл бұрын

Hey just a note for any ford users. This video is 100% correct in every way just for the ford throttle bodies that “coating” is just a load of bs that makes it gunk up quicker nothing to worry about any normal throttle body cleaner will work.

@whydoihave6neutrals772 4 жыл бұрын

I know this videos 9 years old but it’s definitely still the most informative one out for here for people looking to do it

@luisvillegasp 7 жыл бұрын

1:39 my dad gave me same advice when I was 12, Thanks dad.

@280zGaitan 4 жыл бұрын

Or you can get a red rag and clean 🙊🙊🙊

@greygoosemafia 7 жыл бұрын

Everything is illegal in california....

@Minecraftpe135792468 7 жыл бұрын

Richard Cowtails buds not

@Bob-yk9cz 5 жыл бұрын

Yep that's why Cali sucks! I'm here, should really move, I know.

@jerm5772 5 жыл бұрын

You can always move to someplace dirty and unhealthy.

@davidgruen7423 5 жыл бұрын

Jer M area has fumes known to the state of California to cause cancer, it says so near the entrance of the boarding gate in the airport, what is the point?!?!

@pxndxlunx5821 5 жыл бұрын

If you breathe, that will be a $1,000 fine.

@grahamlocklin 6 жыл бұрын

Thank EricTheCarGuy of 2009 for sharing this tip.

@victoruntulis8525 Жыл бұрын

I’m in New York and I was able to pick up an aerosol can of throttle body cleaner from my local advanced. Thanks for the video!

@ericthecarguy 12 жыл бұрын

@JammerEd2 Honestly this video was never meant for electronic throttles as you would not 'feel' the throttle sticking on those. The truth is that I don't recommend doing this to an electronic throttle. Thanks for the comment.

@192ali1 7 жыл бұрын

Dear Eric, Before asking my question, I would like to thank you for your videos. I have watched them all and I am one of your video fans. Can I spray lacquer thinner instead of spray throttle cleaner your mentioned. Lacquer thinners are much cheaper to purchase and I have used them cleaning gummy stuff and works real good. My concern is whether Lacquer thinner can cause and internal problem for the engine or the injectors. Thank you

@Scrubsgetrekt 7 жыл бұрын

BOOM!

@Sloxx701 7 жыл бұрын

Lacquer thinner will destroy any plastics/polymers as well as lubrication/seals on the throttle body shaft. It could also damage the TPS/IAC or other sensors. I would not use it myself, but if you have no choice I would be very careful with it. And I certainly would not spray it down into the throttle body/intake manifold.

@192ali1 7 жыл бұрын

@ Dacke, Thank you for your kindness and sincerely advice..

@Scrubsgetrekt 7 жыл бұрын

Dacke Hey, i just said that.

@MrGuillo5 11 жыл бұрын

Thank you Erik! I have found all your videos extremely helpful! Keep them coming....

@javiergarciaquiroga7169 11 ай бұрын

First time bumping into your channel, and this was a very useful, to-the-point video. Thanks for putting it out there! Liked & subscribed

@raiderman28 9 жыл бұрын

They sell throttle body cleaners at your local Autozone or Oreilly auto parts. Stuff works great. Always disconnect battery when working on a engine.

@SouthMainAuto 9 жыл бұрын

Most cases but not always I would say...

@ArthurSwails 9 жыл бұрын

Raul, before you give this advice, you should consider BMW, and maybe some other brands. If you disconnect the battery, you have to re enter the radio security code before the radio works again. What about the readers of this who don't have their radio code and don't realize they will need it after batt disconnect? You can hook up a temporary 12v supply before you disconnect the battery to save the radio code if you had the knowledge. I wouldn't disconnect battery for most throttle body cleanings.

@michellehoover8946 9 жыл бұрын

@kgisabeast 9 жыл бұрын

That happened on my acura, had to go to the dealer to get the code :/ but hey they'll need to disconnect the battery eventually

@Fetii 9 жыл бұрын

Arthur Swails Really? BMW's are so dumb you have to enter the code everytime you disconnect the battery? Well on Audi's only if you put the radio in another car only then you enter the code.

@jtconner7599 7 жыл бұрын

can i use a can of buttery non stick baking spray? i swear some of the questions in the comments....

@bonfied777 7 жыл бұрын

lmao!

@chrisbyers4726 7 жыл бұрын

J k Glover Not too worried about gluten, but I need Kosher TB cleaner...😂

@huszaratraktor 5 жыл бұрын

Well you can... But should you?

@doityourselfbri 10 жыл бұрын

Good Advice! I have seen this basic service fix many problems.

@bocabec6744 3 жыл бұрын

Thanks Eric. great job and thanks for the "over-spraying" warning. My usual method would be to use 1/2 a can just to "make-sure." A waste of product and not necessary.

@chrisnotap 11 жыл бұрын

it's not really nec. to take the throttle body off. With an old tooth brush and some cleaner you can clean the throttle plate and the area where the throttle plate contacts the body without removal. If you remove it you may be into a gasket replacement or coolant hose leakage (if yours has coolant hoses to it)

@mri136 2 жыл бұрын

But in this way all Carbon enter further into Engine or Carburetor or Combustion Chamber

@johnrkean 9 жыл бұрын

Your positive battery terminal looks pretty bad and needs to be cleaned.

@cengeb 9 жыл бұрын

really, in the last 25 years I never see battery get so foul. Eric must be doing something WRONG. Batterys don't vent and leak like the 70's, how can that corrosion be normal?

@LJRossPhoto 9 жыл бұрын

Clean the terminals, wires, etc.. and put a thin layer of dielectric grease over everything. I've never had a hint of corrosion.

@DanLoFat 6 жыл бұрын

PAying attention to the video, we know it isnt Eric's car AND we also cant assume he hasnt made a ton of videos about this car specifically.

@scose 6 жыл бұрын

galvanic reaction, maybe the wrong type of metal on the terminal clamp.

@thegreatecb 6 жыл бұрын

Hello I have a quick question. The other day I ran some cleaner through my intake vacuum line. There was a backfire that sounded like a small firecracker. Other than that everything went fine. My question is, what is the chance that there was damage to any seals, rods etc.?

@disantoautomotive2420 8 жыл бұрын

I do this every other oil change just for extra maintenance great video

@linerror 10 жыл бұрын

that positive terminal!!!!!

@jessicanicole3224 9 жыл бұрын

Fucking right dude.i just kept looking at it trying to watch eric screw with the trottle

@jpcomas 10 жыл бұрын

to clean you can use throttle body & air intake cleaner (stp) or mass air flow sensor cleaner auto zone

@theoldwizard998 10 жыл бұрын

Great tip on "clear flood mode" ! It is amazing how many people do NOT know this tip !! I think you meant to say not to clean INSIDE Ford throttle bodies, meaning past the throttle plates. Scanner Danner and I have a difference of opinion on this, and you and I are on the same side ! I always clean all external linkages and pivot points

@joecosgrove3593 2 жыл бұрын

Thanks for I really like your method of just removing the snorkel tube. Most other videos have you take out the airbox and a lot of vacuum hoses. I live in California and yes aerosol cleaners are available here.

@kenrickgordon5874 4 ай бұрын

That battery terminal needs help😢 its cry my boiii 😂

@MichaelCoryAnderson 9 жыл бұрын

Thanks EricTheCarGuy....stay dirty man!

@shaunhesselton8155 7 жыл бұрын

eric i love your videos bro they have helped me so much working on my pontiac grand am thanks

@raulferro3998 7 жыл бұрын

Simple but effective. I removed my car's EGR system as well, now I don't have to mind about things like this anymore, well at least not as often as before..

@HelLo-dl4ne 10 жыл бұрын

If you want to do it right way you have to take the throttle out of the car and clean it, so you can make sure the whole throttle is clean.

@exmerion 7 жыл бұрын

What's nice about my Chevy is that I can just remove the throttle body with 2 10mil bolts and clean it off the engine.

@elmooko69 7 жыл бұрын

Thanks Eric! I just cleaned mine out & the throttle is nice & smooth. It was slightly stuck a few days ago and then my IACV started acting up- I'm guessing the gunk from the throttle body may have gotten into the IACV & fouled it up

@mutakasata6752 4 жыл бұрын

Just want to say thank you for the video on cleaning the throttle body.

@donaldtrump9422 7 жыл бұрын

Stay clean bro use some latex gloves silly.

@chrisnotap 11 жыл бұрын

TPS, throttle position sensor, cannot be cleaned. They are a sealed unit. They should not be taken apart and cleaned. They are a precision sensor and should not be messed with.

@mercury0214 3 жыл бұрын

Butthurt

@mercury0214 3 жыл бұрын

And false

@daveroberts6884 5 жыл бұрын

Man to I ever wish I had seen your video 2 years ago. I had a sweet 1998 Buick with the 3.3 or 3.6 liter engine. I was getting run away acceleration and the local garage decided it was a manifold leak and blew the engine up trying to prove that theory. It turned out to be a dirty throttle body but by the time they found that I had a knock on the crank. I sold the car a few weeks later. It was one sweet unit. 6k miles. Ran like new, spotless. I only drove it in the summer. I was not going to throw a new rebuilt in it.

@AQUAFINA20010 10 жыл бұрын

awesome vid eric I have did this and it works good .but I have a question that's got nothing to with this vid... what will make one side of a motor stop firing right??? I have a 02 chevy 1500 with a 4.8 v8 ... the driver side all coils fire good but other side fires poorly.... plz help??

@khalilrazak6486 8 жыл бұрын

This Eric Guy has dangerous side burn's.

@DrMatt96 10 жыл бұрын

i just used WD-40

@js98912 10 жыл бұрын

that wont work thats designed to lubricate not clean

@matthewau9599 10 жыл бұрын

nice try

@metasploited5790 10 жыл бұрын

dont. dont do that. lol things like TB and MAF are special. Dont wanna spray anything that leaves residue. WD40 leaves residue and will build up and possibly do damage to the motor. Besides, TB cleaner is just as expensive as WD40, no sense in NOT using the right stuff :P

@DrMatt96 10 жыл бұрын

Josh Johnson thank you for trying to make me look stupid by just using something i had around the house. a little wd40 isnt gunna hurt anything

@austinschlosser5298 10 жыл бұрын

OG Milkbag Uhhh, yeah, just spray a lubricant into the throttle of your engine, sending it directly into your engine. Would you open up your engine and spray wd40 to clean off oil? no...

@ozzito094 11 жыл бұрын

Eric the car guy is a genious, my car it's running fine thanks to you man!!

@Rampage4reel 8 жыл бұрын

Eric you are right on everything I've seen of yours but I would do this different. I use CRC products whenever I can. If you ever see what happens when throttle body cleaner does to plastic when they come in contact with each other the plastic will crack. Most intake manifolds are plastic. I've always just taken the tb off cleaned it and covered tps sensor and actuator motor so that they don't get wet.

@nikitaw401 9 жыл бұрын

DONT DO THIS ON DRIVE BY WIRE CARS! it will mess stuff up!

@budir2011 9 жыл бұрын

Nikita Wilcox , That's true. I heard that on cars model with drive-by-wire we have to step on the gas to open the throttle, instead. Otherwise , the computer will not function well. Can someone confirm this ? many thanks.

@dennisjohnson2726 9 жыл бұрын

Budi R Yes, Budi, I've heard that. Watch this video for more info. It explains it. Good luc.

@agentjucey 9 жыл бұрын

What's drive by wire?

@MrWesker00 9 жыл бұрын

AgentJucey Electronic throttle bodies. They usually have a module and/or driven by gears electronically. DO NOT MANUALLY OPEN THEM! They will mess up. Ask me how I know!

@dennisjohnson2726 9 жыл бұрын

AgentJucey Drive by wire means there is no mechanical connection from the accelerator to the throttle body. It's done by electronics through your wiring harness, thus drive by wire. It's been used by commercial airliners for many years and is a proven technology.

@car-man 5 жыл бұрын

항상 좋은정보 감사합니다.저는 한국에서 많이 배우고 있습니다.건강하세요! kzfaq.info/get/bejne/irOHipZnnq7MlH0.html

@matrixbikes 3 жыл бұрын

what???

@1supamonsta 11 жыл бұрын

Hey Eric your videos are great. Have a question on this. I have a 2004 4cyl accord and It started having iddle problems right after cleaning the throttle body just like you show here. Could something have been damaged if the engin was not completely cold when they did this? The iddle went up to 2,000 rpm and the Cechk Engine Light turned on for a second and now it's off but the rpms are still high it iddles at 1,500 in operating temperature. Please Help.

@juanitadavis7589 5 жыл бұрын

You were very helpful and quick I just wanted to take the time out to say thank you so much for your video

@cartellove6 9 жыл бұрын

Chrisfix is the type of guy you want to get car reparations and tips from he knows what hes doing, i dont trust this guy. I recommend chrisfix better

@SouthMainAuto 9 жыл бұрын

Have you seen my channel yet by any chance?

@dominicbarile 9 жыл бұрын

Eric And Chris are really good friends actually. They both know what they are doing and honestly Eric is probably more knowledgeable seeing as he is older

@SouthMainAuto 9 жыл бұрын

I don't think age can dictate wisdom...

@dominicbarile 9 жыл бұрын

South Main Auto Repair No I just mean experience wise :) I watched your video of the dodge with electrical issues, that was pretty good :) You should try to promote yourself and get yourself out there!

@SouthMainAuto 9 жыл бұрын

Oh I see haha... well I can only do what I can ya know, unless you know a way to promote I think it is more of a wait and hope people find you game.

@scottyboy2400 7 жыл бұрын

Hey Eric, i would love to see a video on the P0302 Code - Cylinder #2 Misfire! Thanks for all the good videos!

@compactc9 5 жыл бұрын

Having this issue myself! Knew what it was form the beginning though, cleaning the thing out tonight...

@ialnevets 9 жыл бұрын

Easy to understand video. Is this the same for Toyota Camry 2006? Thanks.

@allytheartist 11 жыл бұрын

Definitely trying this to see if it fixes my issue but in the event that it doesn't, what's your take on throttle body "repair kits"? The ones with the set of replacement gaskets and other assorted parts? Replacement throttle body is not available for my car so that would be my only other option.

@bodieboy101 10 жыл бұрын

Thanks for the clear video and explaining how to clean the throttle.

@shwt121 4 жыл бұрын

Hey Eric, Thank you.....very informative about Throttle-Bodies...Before this Ford ZX2 my last one was a 1973 Olds 98 with the Rochester quadra-jet....no throttle bodies here😂👍👍 Thanks again, young man- Wonderful site.😂😁

@SedatedByLife 5 жыл бұрын

Lol post facto, I was thinking "rebel snorkel?" to your small biff in the beginning

@TheThe08989 10 жыл бұрын

Finally a video on this problem. Thank you! very much Eric.

@cobra454tim 9 жыл бұрын

I just posted a question for your live chat about this Eric, Yes in Ca we do still have it, its a red can CRC and says its approved for all throttle body's with plastic coating. Thanks Eric! Timthetoolman

@mushy18100 10 жыл бұрын

Thanks for that quick tip, Eric! You’re the guy! #staydirty -Paolo from CA

@renegadetherapper Жыл бұрын

Did this with my Saab 9-3 and then I just had to reset the codes afterward and so far so good. It’s almost hard to believe such a simple procedure can take your car from a dud to a stud.