RAM TRUCK GAS CAP LOOSE HOW TO FIX ERROR P0456 or P0457

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@chadjohnson7544 4 ай бұрын

So true I bought three mopar and all rattled hahaha

@jakegrock3827 8 ай бұрын

I love how there was no unneeded bullshit. You stayed to the point and didn't ramble on about some stupid irrelevant shit. Good job.

@vdrewerdv 2 ай бұрын

This was the quickest fix I’ve done on my truck. This video was great straight to the point and showed visuals!

@billysmith6317 5 ай бұрын

I watched this video today. Bought the part for 26.00 at oreillys. Installed it in my driveway. Good video. Fixed my truck. Thanks

@JosePonceOchoa-ym4ob 7 күн бұрын

What was the part called

@chrisroday7128 5 ай бұрын

You are very good at how you present the information and troubleshooting. I enjoyed the humor, but more the visual guide, and even how to remove the items.

@aja9469 10 ай бұрын

Hey bro, Had this Issue with my 2015 1500, YOU ARE A LIFE SAVER! Couldn't find anywhere with the info. $40 and a few mins I'm the gutter (Jack Gave out 😂) and I'm good to get emissions cleared away tomorrow. Thanks again for a quick and easy to follow vid

@dawnlee1155 Жыл бұрын

Thank you I’m just a girl with her truck and my stupid gas cap light kept coming on so bought new gas cap but kept coming on so followed your video and was able to do it myself and it’s fixed 👍thanks for sharing ❤

@Ryan-fi8tw Жыл бұрын

Thank you so much I keep on buying gas cap and nothing never changed until I found your videos life saver

@bigdaddyshouse Жыл бұрын

Glad it helped Ryan.

@jasonbaillie3412 Ай бұрын

Fixed my problem and the shake test proved correct! Thank you!

@joshb6469 Жыл бұрын

Took me longer to crawl under the truck than to take it off and shake it lol. Thank you so much for this video.

@BrianAMoore83 10 ай бұрын

This worked like a charm! I really appreciate you putting this video together!

@eduardoortega9922 Жыл бұрын

Replaced a week ago all went fine no more error on screen and today it came back

@joshuaspottedeagle8978 3 ай бұрын

Just changed mine today, it’s been 9 months just wondering how yours is doing now?

@cagedbeauty444 2 жыл бұрын

Legit Big Daddy, your best video yet! Quick and Easy to understand content esp to the everyday person with excellent editing effects per usual, you go boy!!! #RamsesPop

@bigdaddyshouse 2 жыл бұрын

Thanks for the compliment! It took 10 hours to edit that thing. Glad to hear you enjoyed it.

@paulwatson 6 ай бұрын

Great video.... really appreciate the camera view as just describing is not enough for me. When the snow melts, I'll take mine out and see if it rattles.👍

@changolionj.9942 20 күн бұрын

Thank you very much for this video just replaced this on my truck and fixed my problem. Gracias amigo.

@Unfinished-Business24 2 жыл бұрын

Another great video love your content look forward to seeing new videos

@bigdaddyshouse 2 жыл бұрын

Thanks brother, I appreciate the feedback.

@ace3814 2 жыл бұрын

Another great video.

@bigdaddyshouse 2 жыл бұрын

Thanks brother.

@remymartin6772 2 жыл бұрын

this was life changing! so helpful!

@bigdaddyshouse 2 жыл бұрын

Lol, thanks man

@jesusavalos3957 7 ай бұрын

Thank you man that was it first thing it was that thank you man appreciate it keep doing you’re doing a great job

@user-fq4ij8ez7w 9 ай бұрын

Thank You Sir, am waiting for the part to arrive.

@erbenyasharahla6272 4 ай бұрын

Excellent to the point video

@joseirizarry8256 6 ай бұрын

Thanks for the video and explanation, take care blessings.

@SethTheSpeaker 11 ай бұрын

Replaced cap (with a dodge manufacturer) and evap valve. Check engine light and cap light still on. How long did it take for everything to reset?

@danielserrano9443 9 ай бұрын

Try to do what he demonstrates in this video, or get a obd-2 scanner autel brand is good you can get a used one.

@ArizonaLifestyles1 Жыл бұрын

Thank you - this was exactly what I needed

@z31freakify 9 ай бұрын

Just bought 2 new ones and both rattle, only difference is the old one has a sound like broken stuff when holding the plunger inside. The new ones rattle as well but when holding the plunger there's no broken sound. Are the new ones supposed to rattle as well?

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@aubreybrownlee8842 5 ай бұрын

Problem solved Great Video!!

@bobbyfinley6104 Жыл бұрын

Love the Ant Man helmet my buddies got one it's got built-in headphones and a microphone in his that looks like the same one

@chrishansen4731 Жыл бұрын

Did what you said, but the new one rattles! There is a cylinder that slides back and forth so not sure if the old one was actually bad.

@Robert-vv9yg Жыл бұрын

Mine did rattle as well, the new one. But I replaced it and it fixed the check engine light. I wonder if the oring was leaking. the old oring was flat. looked more like a flat washer..I might check the old one with the new oring just to see if that was the problem.

@MechanicWelder94 3 ай бұрын

Was it??@@Robert-vv9yg

@Robert-vv9yg 3 ай бұрын

@@MechanicWelder94 I apoligize. I can't remember

@busta981 5 ай бұрын

How long does it take the code to clear? I have this issue and the duralast part seems to rattle. Confirmed this with a different autozone that had the same part.

@ChasingAnthems 5 ай бұрын

Worked! Thank you.

@amazingrazin 11 ай бұрын

FIxed mine by unhooking the battery and hooking it back up.

@Angeljr1022 Жыл бұрын

Worked like a charm🙏👌

@splitrock4322 8 ай бұрын

Hey thanks so much! That was my issue!

@pabloacosta3080 Жыл бұрын

THANK YOU SIR!

@MrAdk25 Ай бұрын

Thank you

@timkuhn-bv1pr Жыл бұрын

Bought two of these from local NAPA store and one from Amazon…both from NAPA rattled when I took them out of the box. Amazon delivered a none rattler and just installed. Replaced fuel cap also. Light remains on…hoping it goes off tomorrow. Thanks for the info.

@JakeLewis02 Жыл бұрын

Any luck? I did the same thing. Check engine light turned off, gas cap light stayed on. Today check engine light is back on.

@dougeisenhard6816 Жыл бұрын

My Napa one also rattled. Did the code light eventually turn off

@WeThePissedOffPeople 9 ай бұрын

The one i got from auto zone rattled as well and a month later my gas cap and check engine light popped back on.. ordered a new 1 so hopefully it doesnt sound like a baby rattle..

@Mark-sw8kp 8 ай бұрын

I've got the same problem I put two on also any new ideas yet?

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@miltfreberg9582 Жыл бұрын

After changing the valve and clearing the codes out, I still had to disconnect the ground from the battery for about 5 minutes before the light went off

@bahramabdusalamovich3696 6 ай бұрын

It worked, thank you maaaan

@oldcdawg1 9 ай бұрын

fixed it, Thank you

@andrewschoenfeldt5620 Жыл бұрын

Thanks

@kingkills9685 Жыл бұрын

I changed my gas cap and the leak detection valve and my light is still on it’s been 2 days could you help me cause I don’t want to keep throwing parts at it also was I supposed to grease the o ring that can with the valve?

@oldsgamer72cutlass19 Жыл бұрын

I'm having the same thing. I changed the can now the cap light is on truck won't start when it does it idles terrible

@eugenetapper531 8 ай бұрын

Check those tubes, a squirrel chewed a hole in mine right over the fuel tank!

@tylerh743 5 ай бұрын

What happens if the new part rattles as soon as you buy it from auto zone? 😳

@NaRsCaRpe 5 ай бұрын

I just bought mine brand new, Duralast brand from auto zone and it rattles so maybe those do? Did it fix your issue?

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@alfonsosanchezthehandyman4425 Жыл бұрын

Thanks bro

@tomsheets6399 Ай бұрын

I have purchased two of these and they were rattling brand new out of the box. installed one anyway and my gas cap error was gone, but just for a short while and the error message is now back. I wished this would have worked.

@marlinlane2456 2 ай бұрын

I changed that & the purge and it still on & the cap keep coming loose

@dallasbuilt8010 9 ай бұрын

edits go hard

@jammalmurrell8991 Жыл бұрын

My set up is different I have a 2015 lamarie 1500 my gas cap light on and I watch few videos and my under truck is different from the trucks I seen on KZfaq videos

@JuanHernandez-jc6re 21 күн бұрын

Cant find the link to the part brother

@user-vr3dm5rs2v 6 ай бұрын

I have a 13 ram 1500. Replaced fuel cap and evap valve, light still comes on. Upgraded my fuep tank to a 32 gal now because it was pumping at the gas stations. New fuel tank solved the fuel pump issue but gas cap light continues to come on. Possible charcoal canister?

@ToyStoogesVending 3 ай бұрын

I have a 2017 dodge ram truck. gas cap light on and after driving it when parking it i smell fuel so this is the problem?

@geoffboyd 10 ай бұрын

What does this issue cause the truck to do improperly? I understand how to fix it but is the only issue the light on the dash or will it effect performance, gas mileage, or gas leaks?

@pzpinkslip123 Жыл бұрын

Does the check engine light cause a sort of limp mode? I just replaced my gas cap this is next. Truck is definitely running lean. Maybe the engine light or maybe caused by the leak. Either way thanks for video.

@markpolakovich6697 6 ай бұрын

I replaced mine and still get that same annoying light on my 2014, it seems like it does it when the full tank gets to around 3/4 full….suggestions ?

@drake3362 3 ай бұрын

I did shake test on new on and it rattled did I get a faulty one?

@johnnyblaizee Жыл бұрын

Wait I bought the new part and it rattles ?

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@richardcardenas4876 5 ай бұрын

Good afternoon, I hope you can help me with this issue, I got the same message and code and I replaced the Evap Valve, lights went out but after a few weeks the engine light came again with code P0455, I was wondering if you have replace the purge valve or something else to fix this code, thank you in advance

@REINOKGSP 5 ай бұрын

What if you change this part and the light is still on, even after disconnecting the battery for 10 mnts?

@nicholasfields4989 3 ай бұрын

My gas cap light is back on after changing that part and purge valve. Not sure what to do now

@triviumrocker1986 2 ай бұрын

Same here. Not sure what the fix is and I need it now cuz I have to pass emissions in 2 days. So fing stressed over this small but huge problem

@mattrowland9432 Жыл бұрын

Found it in 2 mins. Shake and bake baby

@brentblackburn263 Жыл бұрын

I got the p0456 code on my truck and when I give it gas I hear a whistling noise any thoughts on that?

@bamaman6959 8 ай бұрын

I had the same thing but I change the gas cap first and the light went off so I did not buy the other part

@LostMishima 11 ай бұрын

What about P0463 2017 RAM 1500?

@William76850 10 ай бұрын

Got the gas cap light on. Bought new gas cap & avap valb installed (new) & it’s still showing up. Anyone know what else to do? Should I just remove it with the computer?

@russelproctor9720 Жыл бұрын

Changed part and gas cap. Still showing code and light is still on

@wvu164 Жыл бұрын

Just had it replaced and my gas cap is still on will it go off bye itself?

@bigdaddyshouse Жыл бұрын

Hey William, the system runs checks periodically and it will eventually go off once it sees that it's working. For my fuel cap light, I think it took two to three days before it shut off and it took about 2 weeks for my engine light to shut off. hope this helps Thanks for watching brother

@wvu164 Жыл бұрын

Ok thank you

@wvu164 Жыл бұрын

Hey you ask what video you could make how about resetting the windows it seems like they are alway messing up in the winter more then the summer thank you I have 2016 Dodge Ram big horn .

@wvu164 Жыл бұрын

Had two payments left had two sell no one could get the engine light on or the gas cap just makes me sick

@bigdaddyshouse Жыл бұрын

Weren't the codes just an EVAP leak?

@cham955 2 ай бұрын

Then why does a new one rattle.

@Mark-sw8kp 8 ай бұрын

Put two of those on did not work lights still on

@fastback753 5 ай бұрын

Might have slit in Evap lines

@Hi-jt6qr Жыл бұрын

I bought a new evap valve one and it rattles exactly like your old one is that bad??

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@stevenbrown5210 Жыл бұрын

I replaced that unit. Both the old and new one rattle

@nasseralfeteisi1489 Жыл бұрын

I am also confused cause some say it should rattle, and some don't

@stevenbrown5210 Жыл бұрын

@@nasseralfeteisi1489 the new one rattled plenty. I think the vacuum sucks up the loose piece in there to trigger the switch

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@bigdaddyshouse 2 жыл бұрын

This is the part I used for my 4th gen Ram 1500. amzn.to/2N18rxB

@chadmccoskey7375 Жыл бұрын

How soon until the ligh goes off I installed this and about 15 miles and a few on and off and mine cleared?

@MissionaryForMexico Жыл бұрын

Has to go thru a drive cycle, keep driving!

@WeThePissedOffPeople Жыл бұрын

I bought one and my new one rattled like your old one.. im guessing my check engine light will be coming back on..

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@WeThePissedOffPeople 4 ай бұрын

@@troyperezsr thank you.!

@miguqqeyuiop234qrres9 Жыл бұрын

Do you know where I can buy that piece without the rattle l got the same issue?

@mkrause45 Жыл бұрын

He pin the website in the comments

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@dgenowa 9 күн бұрын

@@troyperezsr i think everyone gets it, you dont need to comment the same thing 100 times. go outside

@mkrause45 Жыл бұрын

Can I still drive it with the gas cap light on?

@abelcerrillo2162 Жыл бұрын

Your engine light will come on next, like mine did.

@mkrause45 Жыл бұрын

@@abelcerrillo2162 lucky it turned off

@robtheslob Жыл бұрын

did this and the code is still showing

@voortman46 Жыл бұрын

The new one rattles as well…

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@TheOfficialKyo 4 ай бұрын

I just bought my my part and it already rattles

@troyperezsr 4 ай бұрын

The shake test is not how you determine if this module is faulty. You test it for an open/closed circuit. It should be "open" with no vacuum or pressure present. With the module disconnected from the vehicle and in the upright position, connect your multi-meter probes to the two pins in the connector. Set your meter to Resistance w/sound and cause a vacuum on the small tube and then a pressure on the large port using your mouth with light pressure. You should hear the internal parts move when you have enough pressure and vacuum. If your meter doesn't beep for both then the module is bad.

@cappyjpadgett 7 ай бұрын

Is that towards the front or rear of truck?

Ең жақсы KZfaq

RAM TRUCK GAS CAP LOOSE HOW TO FIX ERROR P0456 or P0457

Пікірлер: 124