Great case study, you make them simple & easy to follow👍 These systems were quite friendly compared to the newer generations, but still it's a JLR product, I'm sure key programming or AKL on this one will be still as difficult as it's contemporary one's😉 Thanks for sharing Bro, Stay Safe👍

we always learn but i like your way for dignoise thank you Lauis for sharing us

As a follower from your channel I will just say thank you to produce so good videos and you are doing a really good work. A lot of mechanics in my Country (Austria) can't do this or don't have the experience like this. Thx for the videos and nice greetings from Vienna. 👍

I repaired my brothers LandRover, one of the plastic pipes had worn though. It had a microscopic pin hole and took hours to find. The compressor and drier where in a right state but I managed to get it all working.

Helpful repair video 👍

I think my Range Rover 2008 is your next project. It has similar issues. It drops in 48 hours! Then raises very slow. Sometimes it doesn’t raise and gives a bumpy ride!!

Great video 👍

had same problem and chaged out the compressor filter ....good to go

Great case study and solution, I saw you did an eeprom video on a 03 Jeep with the skim /skreem .Just a quick question , I have a Neon to do but The target chip is not the 98050 nor 24-----. IS there any other chip # to use

new great video thanks bro

Happy Easter! Páscoa Feliz!

bom dia doutor.estava esperar de seu video😊 como hoje e domingo entao acorde e apanhe seu video.

I have the same Range Rover but just a 2008 and it’s a Canadian version with left hand drive, I had a suspension fault come up and found a wire hanging down on the driver side wheel area and have no clue to where it leads too on the breaks or anything.

One time i get the freelander with problem of don't started after pain in system of arrefeciment, is necessary original scanner for solve?

I left my email under the Honda repair video, hope to hear back.

I don't blame you for refusing to buy used parts, its a real pain if the parts are faulty. I bought a Haas sensor from Europarts as they did not stock the Bosch sensor. I had endless trouble until I bought genuine a Bosch sensor. It took a while to find the problem as no fault codes came up.

Good job

You make air suspension diag and repair look easy 👍Do you recharge and diagnose AC systems , other than the electrical part of the AC systems?👍

Sweet man thanks

Good video! I'm sure I'm not telling you anything but with the maxisys viewing live data you can select the parameters you want to watch and hit "top" and it will put them at the top so you don't have to keep scrolling back and forth to see them. I think there is a limit but off the top of my head I am not sure what that is. Maybe 4 parameters. Keep up the good work!

Your videos are very interesting and educational. Thank you for making them. On this video, I wonder if the compressor, although showed signs of water, which is not unusual, was the root cause of the issue. It would have been interesting to have seen the voltage at the compressor checked when the compressor was running. Based on what the relay looked like (corrosion, and assumed one of those relays was for the compressor), that may have been why the compressor could not get the pressure up to where it should be. Ensuring the compressor voltage was as it should be when compressor running, would have been a good idea before removing/changing the compressor. Just my opinion. Finally, since you changed both the compressor and the relay, we do not really know for sure. Still, a good video and changing the compressor did not hurt anything given the age of the car. It probably needed changing even if the relay was the problem. Thanks again for making these videos. I know it is time consuming and not easy to do.

boa pascoa pra ti e pros teus tudo de bom

Hello, great video btw. Question though. How fast should the suspension raise from access to highest end? mine is taking about 2.5 minutes to 3 minutes to go up while parked in idle. Thank you

What pressure should I have when the car is moving? because I have this code C1A11-64

4:00 If you don't understand the system, it's very difficult to fix it. Gallery pressure is just the pressure in the pipework, not the tank or the airsprings. 5:00 My guess is your air drier is blocked. Soapy water spray is the best way to find a leak. The drier still needs a service.

great video i just got my land rover sport 06 for only 4k and only 138k miles! but i did see that sometimes when i start the car, sometimes it pops up the suspension dose not affect ride, all i do is turn the car off then on then gone.. any ehlp would be great!

Hi mate need help with adblue system on vw sharan. How can contact u privately plz many thanks

Is anyway to book fot you to repair mine sir ? I'm basic in Glasgow

Bravo to the owner for buying a brand new arftermarket pump

Like every time good

Hello, I have a range rover sport supercharged 2008, I got a suspension fault and I changed the compressor with a Chinese product, The error gon BUT after 2 months (warranty also only 2 months) came again with raising slowly, I think I should to replace it again, right? if yes can you please advise me on which brand I have to use, the original is very expensive

I have a bulb flashing in my dash the whole time while I’m driving is it like some bad flashes on and off? I think it’s the right headlight like the one that turns right left. How can I stop it from flashing and what can I do?

hi LM Auto Repairs ! is there any benefit if i reset the ECU and then reprogramming it again to the car ?? I have an astra van 1.7cdti 2004 and i found a glitch at acceleration pedal sensor.i checked all outputs on that sensor and all values seem to be ok,but when i scan the app1 ans app2 there is a voltage fall on app2. do you have any idea what can be wrong??thx!

My friend good 👍 video. It would be a excellent great video If you show remove & and instalation Of the compressor. :((((( Thx

Hey, Great tutorial. However I'm not completely following. On 12.30 you showed us an obvious leak from the top of the air spring... Then you replaced the compressor. What about this leak from the left front air spring? Was it also replaced or what ?

My car is in normal mode yet setting a tight tolérance code ?

The best and fastest way to find an air leak is soapy water in a spray bottle , turn on vehicle and spray the soapy water on everything that has to do with the connection on the sir system once you see bubbles you found the leak

The problem getting this specific type of fault code is caused by a blocked air dryer Its a normal service part which supposed to changed over the time. Compressor should still be ok

Thank you sir 🙏 that was a brilliant lesson !! I am thinking of buying a Range Rover Sports Julia Stockings 😊❤

Just fill the system with slime puncture repair stuff, works all the time!!

Hey I've got a range Rover seem to blow up for ever and the handling is terrible and both sides different height

Thanks for the video! My air compressor work only around 15-30 sec and it stop and the suspension light go on in the dash! My compressor is new. Anyone have a idea what it could be?

Can you sort mine out?

My Car Range Rover sport 2006 has a small problem at the front of the car is down trying my possible way to raise it up can't get it.

hello my freind ,I need to a i(immo off) file for jeep grande cherokee 3.1td 2001,the MCU is hc11k4 think you very much.

Hi can anybody tell me where the location is of this compressor? Thsnks

😄👍

The diagnostic is much expensive. Is there another way to code it ?

think you ,good job

just for algorithm

Shouldn’t you know the vehicle information before you waste time on the video not knowing

Hy.... I am from Romania, but please give me your adress. I am going to put my Range Rover on a platform and drive it to you. I have also a suspension problem, similar with the one in this video. The only diference by mine, is that I have no yelow light on. In rest is the same. So.... I was in Romania in two dealership services, after in 4 land ateliers, and in Hungary in one. Everiwhere stupid people, and my problem persists. I have changed, 1 compresor, 4 hight sensors, 4 suspension airbags, and still I have the problem. I have also calibrate the suspensions two times. 😩😩😩😩😩 Heeelpppp!!!!!

can you email me as i need you to sort out audi j393 fault neil