Closer to the Ultimate Water-Friendly FPV Drone! (Flotation and Waterproof Tests in River Water)

Рет қаралды 1,221

Күн бұрын

Thanks to PCBWay for sponsoring this video. Check out www.pcbway.com/ for custom printed circuit boards, electronics, and rapid prototyping services (Use my referral link to get $5 of New User Free Credit) www.pcbway.com/setinvite.aspx... !
Hiya, again! Building a water-lovin' FirstPersonView drone has been a bit of an obsession of mine, and I'm always getting a little closer to it! So today I'm testing a flotation setup and waterproofing quality for this 7" FPV drone. This didn't go smoothly, but it was an excellent, educational testing session. My mind is tingling with different design ideas to try. Most importantly, the waterfoofing seems to be holding up well (yes, I know I misspelled waterproofing, but it sounds so funny I left it that way. Pro tip: make sure your antennas stay ABOVE the water when it's floating!
00:00 Hello, Friend. BLUF.
2:32 Our watery adventure begins early in the morning
3:47 Turtlemode / Flip over after crash mode behavior
4:29 First flight
7:24 2nd flight
10:30 3rd flight (almost killed the camera guy)
17:11 4th flight
-------------
🧠 FREE RESOURCES, 3D Printable Designs, and more for FPV Drones, RC Aircraft & 3D Printing at rcwithadam.com/
Want to support RCwithAdam? ↴
KO-FI: ko-fi.com/rcwithadam
OR
PATREON: / rcwithadam
Thanks!
-------
Mandatory Affiliate Disclaimer:
Any links in this description may be affiliate links, which means I make a very small commission (at no additional cost to you) when you make a purchase through that link.
*DISCLAIMER: Remember to always use caution and your best judgement when building and flying RC aircraft, and when working with 3D printers, electronics, or electrical devices. Be mindful of the laws, regulations, and best practices for your particular location. Be a good neighbor, and HAVE FUN!*
-----------
About RCwithAdam: Adam's goal is to HELP YOU build your skills and eliminate frustration and confusion through creative, educational, and encouraging videos featuring Radio Control airplanes, FPV drones, electronics, and 3D printing!
#RCwithAdam #fpvdrone #DJI

Пікірлер: 13

@Sasha_Svarovski 4 ай бұрын

красиво было

@user-wz7ch1mq9h 4 ай бұрын

Hey buddy Amazing video I’m from uk , building 6s waterproof thanks for your in-depth video definitely helping me 😎🤜🤛

@TNT_FPV 4 ай бұрын

👍👍

@georgeaura 4 ай бұрын

That's how I want my quads to be especially my insta360 quad.

@RCwithAdam1 4 ай бұрын

Ooooh yeah! That would be sweet to have half the 360 in the water and half out!

@ninohelf 3 ай бұрын

What did you do with the balance ports of the batteries?

@RCwithAdam1 3 ай бұрын

for this test, I wrapped the batteries in plastic and ziptied around the battery leads.

@3nertia 3 ай бұрын

What is that you've got your transmitter hanging from?

@RCwithAdam1 3 ай бұрын

A gopro chest mount

@jasonwoodruff9131 4 ай бұрын

Another great video. ? I’ve looked all over for videos of how to flash the flight controller. And I have found none. I just built my first drone and I’m using the speedybee f405 v3 on a 7 inch drone. My receiver is a coolrc flysky fs-x6b and my transmitter is a flysky fs i6x. Please help I don’t know where to find the info that it’s asking for

@RCwithAdam1 4 ай бұрын

Gotcha. Unless you're having a specific problem with it, this video from Joshua Bardwell should have the info you need to flash the FC and set it up with betaflight: Betaflight 4.3 Install, Flash, Setup Tab | COMPLETE WALKTHROUGH PART 1 kzfaq.info/get/bejne/gtFyirWaqq2vhH0.htmlfeature=shared . Let me know if that helps.