In this video, i teardown down my first 7 speed Infiniti transmission. Car did not move due to a clogged filter which was caused by a bad converter. Not a bad unit to work on. Thanks for watching, off to the shop this morning
Пікірлер: 37
@nyertsenginetransmission38613 жыл бұрын
Thanks for the time you take to put into these videos! You have your hands full with this one.
@roverM30ds3 жыл бұрын
My 2012 M37 is exhibiting these exact symptoms, thanks for this video. I'm going to tackle this job.
@GaryFerraro3 жыл бұрын
Not a bad trans to work on, be careful
@greggc80883 жыл бұрын
You are awesome! I remember the first transmissions I tore down for tech school. Those were just 3 speed turbo 350's and all the parts freaked me out. I've done Jatco's 40/50 series and CVT for Mitsubishi since they wouldn't replace them and we had no choice, but that's probably the simplest transmission I've seen. You just non nonchalantly lay parts from several transmissions all over the place. I wouldn't be able to sleep at night. LOL I'm going to try again though, because I've got a Challenger with the ZF 8 speed and when the warranty runs out I want to be able to take care of it myself. Good job!
@GaryFerraro3 жыл бұрын
ZF8 speed nice trans to work on, need special tools for that unit
@oldschool97463 жыл бұрын
As always another well made informative video, thank you for sharing your knowledge with us.
@GaryFerraro3 жыл бұрын
Thanks for chiming in every week
@reinaldinhocambiosresende65513 жыл бұрын
e meus parabéns pelo excelentetrabalho e por mostrar os segredos do cambios automaticos
@GaryFerraro3 жыл бұрын
Thank you for watching
@jackmehoff15653 жыл бұрын
Thanks Gary
@GaryFerraro3 жыл бұрын
Thanks for watching Ron
@ou4runnerz3 жыл бұрын
Gary, Great video! Thank you for pointing out the capped filler tube. I was wondering, does that filler tube go all the way to the oil pan? I ask because I would like to do a drain and fill on my transmission and per the factory manual the level needs to be set when the fluid is exactly 104F. Since I can't access the transmission temperature without the Nissan Consult computer, my thought was to use the filler port as a way to gauge the fluid temperature after I have done a drain and fill. Your thoughts sir?
@fastwalker213 жыл бұрын
Put in what you drain out, you will be close. You can use a infrared temp gun on the pan. You will be close when water temp gauge is normal zone after coolant thermostat opens. Filler tube goes into pan. I had the Nissan dealership do my G37S, a drain and fill only drained about 4 qts., they used Matic S fluid. Run it with brake on through gears a couple of times, car level.You would have to do 2 or three in a row to get it looking red and clean. I think I will use the Valvoline Max full Synthetic next time, it is Nissan approved. The Matic S says it's ester based...Which leads me to believe it is semi or non synthetic base oil with an ester package. Do not let anyone run solvent through or use a pressure based fluid exchange system. Tricky deal with no dipstick tube for jack stands and manual pump. Lifetime fluid they try to tell you. Bad joke! Nissan charged me about $150.00. But,will use their fluid.
@ritchiemagalhaes967Ай бұрын
Teste de aplicação nas embreagem vc não faz?
@fastwalker213 жыл бұрын
Too bad that there is very little information on these transmissions, can't even buy a filter. Stealership says non service item...They don't want to change the lifetime fluid ... Even the solenoids numbers can be the same number but have different voltage values for different years and models. Then the ecu won't know what to signal... Many shops will not work on these. Your very meticulous Gary, nice work!
Awesome videos I have a question I have a 6l90e off a 2011 2500hd. It doesnt go forward or reverse gears at all. I tried Drive reverse and manual.
@GaryFerraro3 жыл бұрын
So no movement at all? did this happen suddenly
@blitz86193 жыл бұрын
@@GaryFerraro no movement at all. Idk the truck was given to me. So i dont know history
@Mr.NiceKicks2 жыл бұрын
Would a transmission from a 2015 Q50 AWD work in a 2014 Q50 AWD?? The transmission I’m looking at has 5K miles on it so I want to grab it if it’s compatible I’m just not sure, any input would help. My car was build 9/13 (2014) , The Transmission is from 11/14 (2015 Model Year) thank you so much in advanced!
@GaryFerraro2 жыл бұрын
I'm Honestly not sure, you would have to go by the Vin numbers to see if it would fit
@reinaldinhocambiosresende65513 жыл бұрын
irmão cambio diferente parece frontier 5 marchas
@5.7_TY3 жыл бұрын
Yes the valve body is sold separately just put one in my g37 as it was failing
@GaryFerraro3 жыл бұрын
The valvebody/tcm you purchased as one?
@5.7_TY3 жыл бұрын
@@GaryFerraro yes my g37 wouldn’t shift past 3rd gear and was throwing a code for a bad speed sensor but Infiniti said it was the valve body so they put a new one in it was a 2400 dollar fix (part was $1350).
@GaryFerraro3 жыл бұрын
@@5.7_TY Haven't gotten many 7 speeds yet but i'm sure they will start coming in the shop
@ritchiemagalhaes967Ай бұрын
Tem como vc me da uma dica sobre este câmbio?
@GaryFerraroАй бұрын
Not sure what you mean by exchange rate. Does the trans have a problem
@thiyaguj60343 жыл бұрын
Hi sir can you send parts and give support for doing work .. Am in india and need a assit,
@GaryFerraro3 жыл бұрын
I do not sell parts, what trans are you working on
@gerardohernandez56886 ай бұрын
Can you rebuild mines
@JuliaI.-wf3pwАй бұрын
Why are you doing it? it costs 160 dollars. take another one and put it on. How are you going to assemble this now? I scattered everything and filled it with oil. and what kind of interior is this? What is this, Russia?
@GaryFerraroАй бұрын
what cost 160?
@JuliaI.-wf3pwАй бұрын
@@GaryFerraro yes
@GaryFerraroАй бұрын
@@JuliaI.-wf3pw still confused
@JuliaI.-wf3pwАй бұрын
@@GaryFerraro transmission
@GaryFerraroАй бұрын
@@JuliaI.-wf3pw wow thats cheap, here they are thousands