Reflection and termination Techniques

Рет қаралды 6,398

3 жыл бұрын

Hi Folks,
This video explains about the reflection that occur in the channel due to losses. We have provided techniques to reduce reflection.
Feel free to drop us a comment for any query or suggestions!!
Like | Subscribe | Share

Пікірлер: 25

@EngineerAnandu 4 ай бұрын

very good

@aviralmishra5858 5 ай бұрын

Best explanation of termination on KZfaq

@EngineerAnandu 4 ай бұрын

EMA Design Automation

@agstechnicalsupport Жыл бұрын

Pretty good summary of termination techniques. Thank you for sharing !

@board_design_simulation Жыл бұрын

Glad it was helpful!

@PreludeSon 9 ай бұрын

Thank you so much

@danomurdo 7 ай бұрын

great tutorial

@board_design_simulation 5 ай бұрын

Thanks :) Keep Supporting

@indrajeetpramanik8325 3 жыл бұрын

Very good explanation and topic wise upload would suggest you..but sound is little low..please work on that ...great work keep it up

@board_design_simulation 3 жыл бұрын

Hi Indrajeet. Thanks for the feedback.

@harshbhardwaj3919 2 жыл бұрын

Can you please make a video on Tools explaining the procedure to perform signal integrity analysis on a PCB board ?

@board_design_simulation 2 жыл бұрын

We are planning simulation based tutorials

@VentureHunt_VHF 3 жыл бұрын

When will i expect SI videos on next topic. You are very clearly explaining about the topics.

@board_design_simulation 2 жыл бұрын

Hi Raja, I have been offline for a while... Will start uploading more videos on SI /PI and Highspeed Board Design Soon. Thanks for the Support

@ashwinikumarib2596 Жыл бұрын

Hi, Thanks for the video. Do we use Series and Parallel termination together or only one at once?

@board_design_simulation Жыл бұрын

It depends on the design requirements. But if we talk about the possibility of it, then the answer is YES

@PedroSilva-rm1du Жыл бұрын

Very nice lecture, thank you! May you recommend some book or reference materials so i can study to go deeper in this subject?

@board_design_simulation Жыл бұрын

Hi Pedro, Thanks for being supportive. For signal integrity studies, I would recommend you to read “Signal Integrity: Simplified “ by Eric Bogatin

@PedroSilva-rm1du Жыл бұрын

@@board_design_simulation thank you for your answer!

@chirupavan3599 3 жыл бұрын

Termination is only for reduce reflections ? or if any crosstalk minimization(next & fext) in victims ?

@board_design_simulation 3 жыл бұрын

Termination is used to minimize the reflection as well as cross talk. In later videos series we will show you practical example of how to perform the same. till then stay tuned and subscribe to us. Sorry for the late reply

@gbmewada Жыл бұрын

I want to understand in detail how reflection would occur.. Please help

@board_design_simulation Жыл бұрын

In video i have mentioned that reflection occurs when there is mismatch in impedance profile.

@maheshpalika8985 2 жыл бұрын

Why ground via is required in differential vias. What is the main reason. What will happen if we were not used the ground via.

@board_design_simulation 2 жыл бұрын

Hi Mahesh, thanks for the Query. " The Ground plane acts as a return path for the current. From the basics, if we see" current always flow in a closed loop. That's the main reason we use Ground via to connect and complete the current loop for the particular signal"