Remove and Replace Front Anti Roll Bar Conecting Link Peugeot 308, 307, 3008, Citroen C4, DS 4

Рет қаралды 25,176

3 жыл бұрын

How to replace Front Anti-roll Bar Connecting Link (stabilizer link) Peugeot 308 I, 308CC, 308SW, 307, 307CC, 307sw, 3008 I, Citroen C4 I, C4 II, DS 4.
Links:
- Peugeot 308, 307 Front Anti Roll Bar Stabilizer Link: www.aliexpress.com/item/33023...
- Key Set Combination Wrenches: s.click.aliexpress.com/e/_9jIAMJ
- Mechanic Tool Set: s.click.aliexpress.com/e/_Aa2zDl
- Brushless Cordless Electric Impact Wrench 1/2 inch Drillpro 388vf: s.click.aliexpress.com/e/_AoA3aB
Aliexpress free cupons (up to 19$) for all new accounts: a.aliexpress.com/_d67YNM8
Before buying make sure it is compatible with your car!
WARNING!
Torque wrench settings:
- Anti-roll bar connecting link nuts: 50 Nm (37 lbf ft)
- Whell Bolts: 100 Nm (74 lbf ft)
OE Number for stabilizer link: 5087.64, 96347856, 5087 50, 5087 62, 5087 77
This video is for informational purposes only. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Adrian Dragan (this channel) or KZfaq.
I recommend that you do this in an authorized service.
➢ Facebook Page: / adrian-pgt-diy-repairs...
➢ TikTok: / adrianpgt
➢ If you like, you can buy me a coffee: paypal.me/adioperator?locale....
Comment, Thumbs up, Share, and Subscribe!
Rod Stabilizer link Peugeot
Rod Stabilizer link Peugeot
Strut Stabilizer Peugeot
Strut Stabilizer Citroen DS

Пікірлер: 46

@richardclark4363 14 күн бұрын

Thanks for the video. Just completed this task on a 2009 Partner. Easy enough….but just a note for those that may meet the same hurdle and get stuck: once the retaining bolts were removed from the arm, I had to use a jack to lift the hub/brake assembly a little to allow the captive bolt / threaded section at each end of the arm to be removed from their receiving holes in the suspension. Without doing this the weight of the brake assembly forced the threads into the wrong angle for removal. a couple of persuasive taps did not work. Solution is Lift with the jack 50mm of so and the threads slid straight out. Kept the jack in place to insert new arm. Finger tight the new nuts, release / remove jack and then fully tighten the nuts to spec. My replacement arms came with slightly different fixings to the originals….different size nuts and required an Allen key, not torx. But happy days no more knocking and a mot advisory dealt with ✌

@AdrianDragan 6 күн бұрын

Hello. Your information is good. Thank you!

@volt8684 Жыл бұрын

Nice easy and excellently clearly filmed. Many thanks. I have to replace mine every 18 months because bloody speed humps I think. I use the spray copper grease now, so much less mess😁. Also put grease on hub (where meets the wheel) and clean brake disks calipers by scotch guard and brake cleaner whilst off

@nicolaskang7114 2 жыл бұрын

Man. You are so helpful for my 308. This car have a lot of potential. I enjoy it more than modern cars.

@tu8er861 3 жыл бұрын

Foarte bine explicat 👍👍👍👍👌👌 Ca de fiecare video ce îl publici , felicitări pentru munca făcută

@AdrianDragan 3 жыл бұрын

Multumesc!

@davidaddisonjr.1446 3 жыл бұрын

m-ai învățat să o repar. Mulțumiri

@MastaBruce13 3 жыл бұрын

Nice work!

@user-pw3dw5kl9h 3 жыл бұрын

Good job !!!

@HeavensEye666 Жыл бұрын

Thank you 👍

@danielmicuphotographer7009 3 жыл бұрын

Well done!!

@AdrianDragan 3 жыл бұрын

Thanks!

@Mad4FrenchCars 3 жыл бұрын

Good job mate

@AdrianDragan 3 жыл бұрын

Thanks!

@muratinan1977 3 жыл бұрын

Thanks

@504ownerofficial 3 жыл бұрын

nice

@sulaimanah2185 3 жыл бұрын

Good

@scherenschnitt6333 3 жыл бұрын

Good. But I would use screw glue to secure nut if it isn't selfretaining. And you should not turn the tory screw because of the rubber. It will get weakened.

@robby103165 2 жыл бұрын

Hi, thanks for sharing such a very helpful video. I would like to know if it's the same as the one for the Peugeot 307CC and if yes where can I order it and how much. Thank you again.

@AdrianDragan 2 жыл бұрын

Hello. The same procedure is for 307 / 307cc. I think it would be best to buy the links from a car parts store in your area.

@sulaimanah2185 3 жыл бұрын

✌

@ayoubmouafi6148 3 жыл бұрын

Thnks bro, i like your videos about 308, keep going. I have some noise when i turn the steering wheel i dont know if is the (cardan ou les rotules de suspension) im sorry i dont know the names in english i write it in frensh

@AdrianDragan 3 жыл бұрын

Hello. Is that noise heard when the car is moving and you turn or when you turn the steering wheel when stationary?

@ayoubmouafi6148 3 жыл бұрын

@@AdrianDragan the noise is when the car is moving and the have a little small bosses in the road, for exemple when i turn to another road i hear that noise under the car

@AdrianDragan 3 жыл бұрын

A rotule is probably worn, but it is best to go to the service for a check.

@ayoubmouafi6148 3 жыл бұрын

@@AdrianDragan thnks for your help, and keep going bro... we love what you do... im a 308 owner from Morocco north of africa

@AdrianDragan 3 жыл бұрын

I hope the pandemic passes and visit Morocco once. In Tangier there is also a factory for Dacia cars, Dacia is originally from Romania but is now owned by Renault. Thanks for your appreciation 🙂

@fredrikderiko2322 3 жыл бұрын

"Use Torx wrench T30 to prevent balljoin screw rotation and use combinated key to loosen nut" What exactly do you do with the torx? Do you just put it in or are u holding it hard so it wont twist? I dont get it

@fredrikderiko2322 3 жыл бұрын

To prevent balljoint rotation, i dont get it

@AdrianDragan 3 жыл бұрын

You need the torx wrench to lock the screw so you can loosen the nut.

@fredrikderiko2322 3 жыл бұрын

@@AdrianDragan Oh okay thanks!

@JD-ec7rx 3 жыл бұрын

Salut Adrian, am și eu o întrebare in legătura cu motorul 1.6hdi , de ceva timp văd murdar de ulei westgateul de sub turbo .. ai vreo idee ce ar putea fi ?

@AdrianDragan 3 жыл бұрын

Salut. posibil sa fie ulei de la garnitura ce etansaza tubul de admisie aer pe intrarea in turbina. Reperul 14 din imagine: ci.catcar.info/peugeot/img/pr/42/00067542.jpg O alta cauza poate fi o saiba sau chiar surubul ce tine conducta cu alimentare ulei a turbinei sau cea de la evacuarea uleiului din turbina.

@JD-ec7rx 3 жыл бұрын

Ok, o sa controlez mersi mult . Big up 🤙