Replacing a worn out wheel bearing

Replacing a worn out wheel bearing - Nissan Navara D40

Рет қаралды 117,877

Marty T

2 жыл бұрын

Nissan - Navara Pathfinder Xterra Titan Frontier

Пікірлер: 375

@adrianparker5587 2 жыл бұрын

I almost feel cheated as that was a hub change. No Marty invention to get the bearings out using only a teaspoon and the top of a Coke bottle.... Your videos always brighten up the day. Thank you for making them.

@Matty.Hill_87 2 жыл бұрын

😂😂

@mattj630 2 жыл бұрын

Loaded hubs are cheap for these, but you’re right. Lol

@jdmccorful 2 жыл бұрын

Ditto!

@TWX1138 2 жыл бұрын

@@mattj630 If I remember correctly there aren't unloaded hubs available. there's no separate bearing race to knock out of the hub assembly to change only a small part.

@604116 2 жыл бұрын

Marty will never know the joy of living in the rust belt. If I made a video of the last wheel bearing I did it would be like the filming of Apocalypse Now.

@weegrant1980 2 жыл бұрын

Ha ha, we have the same problems here in Scotland, everything is usually corroded and seized, nice when you get one like Martys

@johnandersson 2 жыл бұрын

As a Scandinavian I strongly relate to this comment.

@69jbr69 2 жыл бұрын

I was gonna say same thing, northern WI here. What size bolt is that? Doesn't matter, just hammer the tightest size impact socket you can on rusted nub and get the pipe wrench and than drill and taps and welder ready just in case. This is after a week of presoaking and splash of torch if you are lucky and than get ready to look like you're ready to fight galactic battles with silver surfer after you heavy dose everything you can with anti seize on reassembly and it has now magically covered your whole body and part of interior and somehow got in fridge. Don't even look at the brake lines or exhaust or you will be fixing those as well. First drive rusty piston in brake caliper sticks because you touched it and reheat treats new bearing and you have run out of swear word combos. If you have never spent a whole day on one bolt, you are not a rust belt mechanic.

@sparkplug94 2 жыл бұрын

The struggle is real. Torch set is a required tool.

@Nas_Atlas 2 жыл бұрын

Imagine living somewhere where the roads aren't sprayed with salt 7 months of the year

@tanner4828 2 жыл бұрын

I've never been interested in mechanics and have (almost) no mechanical abilities, but for some reason I like watching Marty do this stuff. Maybe some day I will attempt something more than an oil change.

@ezeckielthomas6798 2 жыл бұрын

I'd suggest changing brake pads, since this is fairly simple and very satisfying. You will get dirty tough!

@Brad.whatthe 2 жыл бұрын

That hub came out nice and easy, bit of a bonus really not having roads salted, all the salt in NZ goes on the fush and chups

@lot6129 2 жыл бұрын

$6.66

@BrassLock Жыл бұрын

I'd luv to have Kiwi or Aussie Fush-n-Chups right now. Greetings from Chiang Mai 🇹🇭 where some places provide "crisps" in place of Chups.

@meirionevans5137 2 жыл бұрын

For those of you that may have missed it, that was 274-364 Newton Marty's on the torque tube.

@iainarthur7713 2 жыл бұрын

accurate metric measuring using 1m of 48.3mm scaffold tube shoved over a bar and leant on a bit, but not a lot

@dot7107 2 жыл бұрын

"factory specs" 👍😁

@locknload4691 2 жыл бұрын

Somewhere between 1-2 ugga duggas🤔

@useitwice 2 жыл бұрын

I wish I was born like 10 years ago and you were my dad. You seem so relaxed, and you can do almost everything the world throws at you. Cheers / your almost 40 year old kid from Sweden

@brandonconard 2 жыл бұрын

I absolutely love how smart and talented you are, I found your channel back in 2019 and i have been watching ever since, I love your content

@martialme84 2 жыл бұрын

Excellent video. I drive a fairly similar car and, after watching this video, decided to change the hubs myself when they're up. Thanks for this video, marty.

@Alexander-ri1bp 2 жыл бұрын

Nice job Marty :) When I do this kind of jobs, I like to use the pressure washer first to get the dirt out, less dirt on parts, hands, etc.

@olemanwoodworker5152 2 жыл бұрын

This brings back so many memories as to when I was raising a family. Needed to fix and learn how to fix items from the house to the auto and all in between. Thanks for sharing and bringing back memories.

@DarkFlamage 2 жыл бұрын

You ever walk down the street in front of my house, I'll hand you a cold beer!

@Monkeysic 2 жыл бұрын

Super jealous at the rust free parts! Around here they dump so much salt on the roads in the winter you would have had to torch every last bolt at least to break them loose if not torch them off, then beat the snot out if the bearing to get it out! Awesome job none the less!!!

@VoteBlueNov.2024 2 жыл бұрын

Chuckling about no parts left over. Nice Friday morning video. Thanks Marty.

@Marcelo-56 2 жыл бұрын

4:29 Lubricating before assembling is a very good practice☝ because most mechanics don't do it and over time it becomes VERY difficult to disassemble metals👍

@aserta 2 жыл бұрын

Most mechanics forget parts. That's how they end up with bins of bolts. :))

@RadicalEdward_115 2 жыл бұрын

@@aserta unprepared and incompetent mechanics maybe but any mechanic worth a damn knows how to store bolts they remove for reassembly

@dot7107 2 жыл бұрын

Meh, when there is some leftover bolts and nuts, car is just lighter and goes faster 😂

@Marcelo-56 2 жыл бұрын

@@dot7107 🤣🤣🤣

@krpo1840 Жыл бұрын

Is thats a lubricant or some kind of grease ?

@silentninjer1 2 жыл бұрын

Nice job, we have a an anagram for navara here in Blighty Need Another Vehicle And Roadside Assistance

@MartyT 2 жыл бұрын

😂 this one has had its share of problems, one time it forgot how to change between 2-4wd

@alfiembra 2 жыл бұрын

A tip I was given to check a wheel bearing that you can’t see any obvious movement or play, is to spin the wheel and with your other hand hold onto the spring and if the bearing is bad you will feel vibration through the spring.

@rhiantaylor3446 2 жыл бұрын

Its a good thing you had a calibrated 274-365NM extension tube for your T bar, mine only goes up to 250NM. If it had been me trying to do this, I would have spent half the day releasing the drive shaft from the old bearing assembly.

@keyera1378 2 жыл бұрын

I love the fart sound effect you add whenever the grease gun is in the shot.

@MrDaleyates 2 ай бұрын

Thanks going to give it a try just ordered parts mine sound the same and give a vibration at 95 to 110 so got some play. A mechanical strore wanted over 1 grand in Australia plus parts to do this. Ebay 150 for a set of 2. Have rebuilt everything else in under the arch so easy thanks mate for your video will let you no how i go in a few weeks

@joshbaker2437 2 жыл бұрын

Thought I was watching Eric O at SMA for a second lol. Great video

@DominicClifton 2 жыл бұрын

Nice to see I have the same taste in 4x4's as Marty T :D Did this job on my 2006 Navara a couple of years ago.

@markkneale 2 жыл бұрын

How do I get so excited when I see a new marty t video. Maybe its just coming of age , maybe its a dad thing . I dont know but top vid as always marty . Hope you and the family are all well buddy.

@johnniewelbornjr.8940 2 жыл бұрын

A good common-sense approach to this job. I have seen too many people go into a repair with tunnel vision, not looking at other things that might make more sense to repair at the same time while everything is apart. Thinking ahead to making life easier the next time is always a plus, as well. Thanks for sharing and have a great weekend!

@eldraino9933 2 жыл бұрын

He needs a milwaulkee cordless impact wrench- my compact 12v one has incredible power - I’d def be using loctite on those hub bolts

@Meatlove Жыл бұрын

As an automotive professional I have to say: Very clear and informative video. Safe and tidy craftsmanship. I couldn't have done it better myself!

@larrylane6512 2 жыл бұрын

Another well-done job Marty

@AB-C1 Жыл бұрын

Great video Marty! Really well explained, demonstrated and filmed. Always concise no bull, (no padding it out with rubbish) 100% USEFUL INFO &tips! Cheers 👍🏴󠁧󠁢󠁥󠁮󠁧󠁿

@russw5301 2 жыл бұрын

Another great informative and practical video. Thanks Marty. I did expect to see you replacing the bearings in the hub, but Nissan saved some work. Love your videos.

@donhalford2237 2 жыл бұрын

Ah, yes. Another great tutorial.😁 I Learned a lot from that video, Marty. I'll call you if I need some wheel work.

@mischef18 2 жыл бұрын

Enjoyed this video bro. Having a complete bearing thing to just pop back in sure saves taking out and banging in new bearings let alone getting covered in grease.Safe travels

@udnystation 2 жыл бұрын

Great vid, I followed your example and change the front bearing on my pathfinder today. Most was straight forward but those 4 bolts on the inside were a pain. I also seem to have more rust in Scotland than you do. The bearing was actually stuck to the hub. Managed it though 😀

@SzonSer 2 жыл бұрын

I see the barking spiders got into the grease gun again Marty 😂

@lonhoschar1943 Жыл бұрын

Nice Job Marty!! I need to put a new cv axle in my old 94 Chevy K1500 pickup. Getting a "thump, thump, thump" when going around curves😁

@GKsGS400 2 жыл бұрын

Looks like you guys have a rocket launch tomorrow from Launch Complex 1 over on the Mahia Peninsula. Good Luck!!

@BensWorkshop 2 жыл бұрын

good work. Don't like the way they made you use a breaker bar on a universal joint, but it is what it is.

@michaelschuenemann3505 2 жыл бұрын

Great Wheel Bearing Maintenance - Job well done ! Cheers from Australia !!!!

@freeman7788 Жыл бұрын

Marty ya a good mechanic. As a fitter machinist and diesel mechanic i was taught never tighten in a circle always opposing nuts...Top bottom left one top right one repeat..

@tonymckeage1028 Жыл бұрын

Great Video Marty, I envy your skills mate, well done!

@warrenvalentino5763 2 жыл бұрын

Awesome video. glad that you caught it before it broke. love watching your videos. :)

@bennyogden4524 2 жыл бұрын

I enjoy all of your videos man keep up the good work

@kerrygleeson4409 2 жыл бұрын

Thanks for sharing Marty 🇦🇺🦘👍

@deanbarr5740 2 жыл бұрын

I recently replaced the left front wheel bearing assembly in my 2012 Chevy Colorado. The bottom rear bolt in the back of the 4 bolts really gave me a hard time. After a few skinned knuckles and mashed fingers it finally came out.

@billyhaddock5540 2 жыл бұрын

Great job doing the wheel bearing.

@michaelmcclure8673 2 жыл бұрын

Another great repair Marty t .

@G3516dude 2 жыл бұрын

Excellent video, thanks for the tips. I’ll definitely do my own on our D40. Cheers mate

@WelcometoVideoCity 2 жыл бұрын

You always make it look so easy.

@terrencebuller7676 2 жыл бұрын

Nice job Mate, always look forward to seeing your videos. Take care and be good. 👍

@prassmancreations3168 2 жыл бұрын

Thanks for reminding me I need to do this to my Rodeo this weekend

@fairstnaimelastenaime1346 Жыл бұрын

it really helps if you had mechanically inclined relatives to mentor (not I)- i almost replaced cv boots one time but didn't have the right tool/socket....and of course necessity the mother of invention, so a poor rural person better than urban rich person.

@thomaskilpatrick8531 2 жыл бұрын

Small tip you can put a screw driver in the holes of a vented disc and jam it from turning the wheel instead of putting the wheel back on ,we do it all the time

@francotrovato6725 Жыл бұрын

No parts left over 🤣🤣 thanks for the content mate!

@bellofbelmont 2 жыл бұрын

So I take it the two foot long pipe is your 274 to 364 NM bar and your three foot pipe is 365 to about 450 ...... 🤣🤣 .... Good enough for the bush! Love your vids. Jim Bell (Australia)

@MartyT 2 жыл бұрын

Yeah you can get it pretty close to spec by gauging the weight on the bar and judging the distance from the socket to the point of applied weight, also taking into consideration whether the threads are dry or greased

@regalbowman3143 2 жыл бұрын

Great channel Always interesting and diverse content

@northerner1374 2 жыл бұрын

Still some life left in the old girl yet! 🤩👍🏻

@rotaone8513 2 жыл бұрын

A quick way to tell which front wheel bearing is noisy is to drive the vehicle in a straight line, turn the wheel to the right and then the left. The noisy bearing will be opposite to the direction you turned the wheel. The reason this works is that the vehicles weight is transferred to the opposite wheel of the vehicles direction, putting the bearings under heavier load. One of many tricks i learned as an apprentice mechanic some 48 years ago. I should add, this test should be done on smooth, traffic empty roads, not Marty dirt tracks.

@MartyT 2 жыл бұрын

Yes I did actually notice this while driving on the road

@Kowyn 2 жыл бұрын

Another way to get the nut off is as you said with the wheel back on but to then use a jack on the end of the breaker bar.

@seafieldgrant6957 Жыл бұрын

I wish you best of luck dealing with this. We also have major slides here in Alberta Canada.

@AndyMcBlane 2 жыл бұрын

Nice video Marty!

@reecerx7 2 жыл бұрын

Good video. If you own a d40, a impact wrench is by far the best investment to buy if you plan on keeping it for a while ! On my 4th d40 now and almost every one has done a wheel bearing at some point. STX 550 owner now

@yeagerxp 2 жыл бұрын

Good job 👍👍👍Thank you for sharing. Take care of yourself, be safe, and healthy 🇨🇦

@kathylondon-anthony368 2 жыл бұрын

Being a mechanic in eastern Canada, I'm offended at how easily that frigging hub fell out of that knuckle, lol

@brianmackey6923 2 жыл бұрын

Job well done Marty

@littlejason99 2 жыл бұрын

I had to change a front hub on a 2wd pathfinder, very similar. Hardest part was getting the stupid ABS cable disconnected it was all caked with dirt.!

@harryburford6629 2 жыл бұрын

well done mate very simple

@sexocet8523 Жыл бұрын

Wow I’ve done 340k or 220,000 miles and not done bearings yet but noticed a little noise so might be worth while swapping as that is so easy!

@rb3425 2 жыл бұрын

Lucky it was that design! Some other types (especially older designs) are pressed into the steering knuckle with the ABS ring on the outside of the CV joint housing which was easy to damage.

@guycarignan2263 2 жыл бұрын

Very informative. Thank you for posting. Very good video.

@TechGorilla1987 2 жыл бұрын

G'Day there, mate!

@snapon666 2 жыл бұрын

Now you might as well do the other side as preventive maintenance ....my experience with Japanese cars is that have an almost timed failure ..if one side goes the other is not far behind ....in the US those half shafts are cheap enough to also replace at the same time ...again if you already have it apart it saves on labour later

@cynzhero62 2 жыл бұрын

Morning marty!.cheers.

@willf5768 2 жыл бұрын

Great job well done M T 😁👍👍👍👍👍

@bobjoncas2814 2 жыл бұрын

...lookin' good , keep safe and have a good weekend...

@whathasxgottodowithit3919. 2 жыл бұрын

Must be great to work on vehicles without the curse of winter salted roads, thank you for posting Marty.

@pauldecember1207 2 жыл бұрын

thanks again marty

@organiccold 2 жыл бұрын

Job done. Have a nice weekend.

@neildriedger637 Жыл бұрын

AWESOME Marty!!!!👍

@willemvantsant5105 2 жыл бұрын

Hi Marty, just changed the front wheel bearings on my Ford Laser, water always finds it's way in.

@MartyT 2 жыл бұрын

I think the grease found its way out of this one

@markroth9827 2 жыл бұрын

Thank you for your video.

@RickSolid1 2 жыл бұрын

Very similar to my Nissan Titan, I think the navara is the frontier in NA/CA/SA, so it’s makes sense to have similar designs. Nice job Marty.

@organiccold 2 жыл бұрын

Yes it is the Frontier in North American markets. The Mercedes X Classe is also a Nissan Navarra

@TWX1138 2 жыл бұрын

Only oddball for the Navara, there were slight differences between the various international plants producing them, some parts are different whether they're Spanish-sourced, Thai-sourced, or American-sourced. Ball joints in the UCAs vary as an example. But they're all very similar.

@margaretwilkinson9140 2 жыл бұрын

thank you mr t

@AquaMarine1000 2 жыл бұрын

Thanks for the warning.

@Spongman 2 жыл бұрын

there's so much great information in this video, but the reason I hit the 'like' button: the extra fart sounds.

@reecewhitehead2745 Жыл бұрын

Bearing wholesale’s bearings, good stuff

@jamesbreault5762 2 жыл бұрын

Looks good

@jcramond73 2 жыл бұрын

Nice one Marty, just one nit pick, use impact sockets..if you have them :)

@lrdisco2005 2 жыл бұрын

Some good axle stands are a good idea, keep safe

@MartyT 2 жыл бұрын

That old steely will hold 3 ton easy ;)

@mudemmeonick 2 жыл бұрын

Never took you as the type of man to fancy rebadged Passats...

@peterhall6656 2 жыл бұрын

The scissor jack I used when I was rallying had a 19mm bolt welded on so we could rattle the car up in 3 secs.

@kennethbolton951 2 жыл бұрын

Damn Mar tay You are so good you could work in a garage , any garage, any kind of vehicle, hell , anything mechanical, we all hate you, just kidding. Kudos.