Testing and replacing nozzles on the 1964 Ford 4000 diesel. Same for injectors as a Ford 601, 801, 901 tractor. Video of tractor starting 16 minutes in. • Walk Around of Ford 40...
Пікірлер: 27
@RichinZhills2 жыл бұрын
Wonder if you can maybe try some Teflon tape to see if you can get the Knob to work without leaking.
@jumongISPISO2 жыл бұрын
Hello.. Good day, just wanna ask, from what engine is that injector? And what would be the best PSI for that kind of type?? Tnx..
@chickenhousemechanic2 жыл бұрын
Injectors were the original ones out of a 172ci 4 cylinder diesel. Pop off pressure is 2750 psi.
@philliphall5198 Жыл бұрын
I set the 961 at 1750 if I remember right, according to manual
@steveashworth67072 жыл бұрын
I priced new tips verses the whole injector and the cost difference was 30 dollars more for three complete injectors so that's what I ordered!.
@cesaruribe82802 жыл бұрын
Isn’t it a 4 cylinder?
@cesaruribe82802 жыл бұрын
Where did you get..?
@karlandrefrantzen6709 Жыл бұрын
Did you make a adapter and fit it to the injector in order to connect the pressure tester?
@chickenhousemechanic Жыл бұрын
The metal line came with the injector tester. It has another one too.
@karlandrefrantzen6709 Жыл бұрын
@@chickenhousemechanic Thanks for the replay, i hope the pressure test set i ordered fits my ford 3000 injectors as it is.
@chickenhousemechanic Жыл бұрын
@@karlandrefrantzen6709 you're welcome. Going off memory I want to say the tester I bought came with a 14mm and 12mm adaptor. Can't remember the thread pitch though. Kinda coarse, maybe a 1.5mm thread pitch.
@karlandrefrantzen6709 Жыл бұрын
@@chickenhousemechanic Mine comes with 3 adaptors but i would think that the threads on the injectors are in inches so lets see if the kit will fit when yours is metric
@kubaSWAT2 жыл бұрын
hi you have the knob on the right, whats for? how to use it thanks
@chickenhousemechanic2 жыл бұрын
From what I understand it is a way to relieve pressure to the injection. Others online have said the tool leaks if you loosen it so I just left mine tight and relieved pressure by cracking the line fitting at the injector.
@kubaSWAT2 жыл бұрын
@@chickenhousemechanic but for pop testing how should I set the jnob
@chickenhousemechanic2 жыл бұрын
@@kubaSWAT had mine turned all the way in so the pressure didn't bleed off.
@kubaSWAT2 жыл бұрын
@@chickenhousemechanic got it thanks, and the tester doesnt leak ??
@chickenhousemechanic2 жыл бұрын
@@kubaSWAT nope. Kinda surprised at that honestly.
@napper14962 жыл бұрын
What about pre injection?
@chickenhousemechanic2 жыл бұрын
As far as I know these injectors do not have any pre injection. Service manual doesn't mention anything either.
@jeremyhastings84132 жыл бұрын
Where did you order your nozzles from?
@chickenhousemechanic2 жыл бұрын
I looked through my papers and spreadsheet and I apparently didn't write it down. Most likely I bought them from Just8ns.com. Part number for the 1958-1964 injectors is C5NE9E527A.
@jeremyhastings84132 жыл бұрын
@@chickenhousemechanic thank you I'm rebuilding my 63 4000 industrial and your videos have been a great help along with the manual
@chickenhousemechanic2 жыл бұрын
@@jeremyhastings8413 glad to hear that. I try to make the videos thorough without being too boring. The manual is a great help too.