Replacing the High Pressure Oil Pump (HPOP) on a 7.3 Powerstroke Ford F-250 Superduty

Рет қаралды 49,285

Күн бұрын

Replacing the High Pressure Oil Pump (HPOP) on a 7.3 Powerstroke Ford F-250 Superduty
#ford #powerstroke #fordtrucks #superduty
► Buy Merch Here: project-time-garage.creator-s...
► Follow us on Instagram: / projecttimegarage
► Like us on Facebook: / projecttimegarage
► E-MAIL US: projecttimegarage@outlook.com
► Our mailing address is:
Project Time Garage
1113 Murfreesboro Rd
Suite 106
Mailbox #109
Franklin TN 37064
***Links to products I use, or are seen in the video***
• Bluetooth OBD II Adapter: amzn.to/38oEKie
• Milwaukee 3/8" Cordless Ratchet Kit: amzn.to/3kNozhg
• Milwaukee 1/4" Cordless Ratchet: amzn.to/3i1saXx
• Topside Creeper: amzn.to/3iPZ7YG
DISCLAIMER: Links included in this description might be affiliate links. If you purchase a product or service with the links that I provide I may receive a small commission. There is no additional charge to you! Thank you for supporting this channel so I can continue to provide you with free content each week!

Пікірлер: 146

@donsgotmoney Жыл бұрын

I remember years ago when Ford road tractors were using Cat 3126 engines, we used to always get a situation where the was low oil pressure at the HEUI pump. I was replacing the IPR on a regular basis till one day I decided to take it apart. There is a very small hole on the shaft of the IPR, that hole would get the slightest bit of trash stuck in it and cause a no start issue. When the solenoid in energized, it pulls a metal pin/bullet through the tube, this is what I believe regulates the pressure going through the IPR, if that metal bullet is compromised in any way it will upset the pressure demanded at the injectors. Its been 20 years since ive messed with this type design, but im really enjoying your videos.

@ProjectTimeGarage Жыл бұрын

That's great info. I appreciate it!

@stevebarton9469 2 жыл бұрын

Thank you! Your videos are extremely helpful and some of the best I’ve seen. I own a 1997 F3 50 with over 400,000 miles on it and with your help I have found out some of the aging problems. SUPER helpful! 👍👌

@ProjectTimeGarage 2 жыл бұрын

Glad to help

@stevebarton9469 2 жыл бұрын

We replaced all fuel injectors and fuel pump. The injectors only had 3 good out of eight. We changed all. We made many attempts to start truck but won’t quite start. We are only getting about 400 pounds from the high pressure oil pump during the starting procedure. The high-pressure oil pump has never been replaced and has over 400,000 miles on it. What pressure should the 73 beer when you’re trying to start the motor? Could the High pressure Oil pump be the reason it won’t start if it’s bad? Your thoughts?

@KyJack13 Жыл бұрын

“Pointer” had me rollin

@ProjectTimeGarage Жыл бұрын

Yeah, love me a good pointer.

@billmalec 3 жыл бұрын

Actual REAL MUSIC. Thanks.

@ProjectTimeGarage 3 жыл бұрын

Thanks! You wouldn't believe how hard it is to find decent music for these videos.

@Motoracer0172 6 ай бұрын

Love this channel , you make tackling these jobs far less complicated than originally thought. Prior to watching your channel I wasn't confident enough to attack this challenge myself. However, now I most certainly am, thank you so much!!! Maybe without the music though lol.

@ProjectTimeGarage 6 ай бұрын

Thanks, yeah the music choices that were available to me back then were not great. Much better today, though.

@josh1800 Жыл бұрын

Literally name it, "The truck with no name."

@ProjectTimeGarage Жыл бұрын

Ha, I like that.

@powerstrokediesel99 2 жыл бұрын

not gonna lie I was going the spring and check valve!!!! before you pointed it out that he forgot them at first haha! great video as always!!

@ProjectTimeGarage 2 жыл бұрын

Thanks 👍

@packingbone1953 2 жыл бұрын

Very good instructional video thank you

@ProjectTimeGarage 2 жыл бұрын

Glad you enjoyed it

@renegaderader7573 Жыл бұрын

Liberty .. freedom & liberty

@ProjectTimeGarage Жыл бұрын

Exactly what I said too!

@DeepSouthBayouDiesel 3 ай бұрын

I know I'm late to the party, but I agree... liberty and freedom 😎👍

@jfitzerelli 2 жыл бұрын

Again. Nice job sir👍

@ProjectTimeGarage 2 жыл бұрын

Thanks again!

@danielboyne258 3 ай бұрын

Freedom and liberty

@ProjectTimeGarage Ай бұрын

Yep, cool.

@ryanhogue9103 2 жыл бұрын

I am really enjoying your videos. Can you tell us more about the setup you are using to read the hpop pressure?

@ProjectTimeGarage 2 жыл бұрын

Yes, pretty simple really. Just a plain old Android tablet with a bluetooth OBD-ii reader and 2 apps one is called ForScan and the other is called TorquePro, both available via the Google Play store.

@michaelwalker1152 2 жыл бұрын

Legend

@ProjectTimeGarage 2 жыл бұрын

Thanks!!

@middlefingersquad1695 8 ай бұрын

Freedom Rains

@ProjectTimeGarage 8 ай бұрын

Cool

@Submarine_SeXJ Жыл бұрын

I’d just go ahead and replace the HPOP lines and delete those check valves while you’re in there. Them check valves can create issues.

@ProjectTimeGarage Жыл бұрын

Definately should have done that while we were there.

@BarryPacock-is8ld 7 ай бұрын

I have a question for you. I have an 00 f350 with the 7.3l only has 90k miles was a pit truck was never abused. Runs great but it's a bitch to get started first thing in the mourning usually have to crank it over 4 or 5 times before it will finally fire up. But dosemt show another symptoms of any kind. Do ubthink it's the hpop or the low pressure pump. When I run it threw my mind it feels like its loosing g pressure over night and have to crank it a bunch for it to build presure back up for it to catch.

@Submarine_SeXJ 6 ай бұрын

@@BarryPacock-is8ld well if you let it sit for a over night in the morning pull the plug to the hpop reservoir if there no oil in it then your LPOP is on its way out. Could also be a classic case of glow plugs/glow plug relay. When my hpop started going out I wouldn’t start at all unless oil temp was above 80°

@darrentylor5473 2 ай бұрын

Ole' Red

@ProjectTimeGarage 2 ай бұрын

Good name.

@morongene 6 ай бұрын

Yeah. I may have to tackle this job at some point, and keep reading that you need a special snap on socket to remove the ?ICP sensor? I see you using a double sided spark plug tool for that job. Were there any struggles to get that off?

@ProjectTimeGarage 6 ай бұрын

Actually the tool I used is called a Shower Flange Tool. It's available as a kit in the plumbing isle of Lowes/Home Depot. But, you can do it with a standard deep well socket too.

@Blah86683 Жыл бұрын

Will that Forscan tool you used on your last video read those oil pressures?

@ProjectTimeGarage Жыл бұрын

Yes, sure will, so will Torque Pro (if you add the additional Ford PIDs). This is the Bluetooth Dongle I use: amzn.to/3XyIpjP

@robertserna2147 3 ай бұрын

Big Red

@ProjectTimeGarage Ай бұрын

A fitting name

@alanarmstrong2323 Жыл бұрын

There is an oring on left side of timing cover for antidrainback as well

@ProjectTimeGarage Жыл бұрын

Good info, thanks!

@alanarmstrong2323 Жыл бұрын

@@ProjectTimeGarage only reason I know this is I too have a 2000 f250 7.3 best diesel motor made.

@ProjectTimeGarage Жыл бұрын

@@alanarmstrong2323 Agreed 100% Did you see the latest video I did? $500 7.3

@chriswithrow3107 3 жыл бұрын

Hey you gotta add your two popup video links in the very beginning, the ones you pointed at

@ProjectTimeGarage 3 жыл бұрын

Man, thanks Soooo much for pointing that out. I'll get it fixed asap!!

@ProjectTimeGarage 3 жыл бұрын

Hey Chris, shoot me your email address when you get a chance projecttimegarage@outlook.com

@youknow9328 Жыл бұрын

What version of forscan are you using. The regular one or lite ?

@ProjectTimeGarage Жыл бұрын

Lite. I also have a video covering Forscan and TorquePro from a "getting started" perspective.

@ladislavleitner1729 2 жыл бұрын

Hi, at 5:55 - what tool is that to remove the hoses?

@ProjectTimeGarage 2 жыл бұрын

It's a tool made basically just for unplugging those lines. You can get it here: amzn.to/3trnu54

@jamesb1988 Жыл бұрын

I'm 99 percent sure that I am going to tackle this job my myself instead of paying shop.... The only part I'm somewhat concerned about is the 18mm bolt behind the RTV'd cover, is there anything i need to be weary of in this section? Also, do you have any recommendation from who I should purchase HPOP from? Or what kind? My truck is a 2001 F-250.

@ProjectTimeGarage Жыл бұрын

Do it. It isn't that hard. There is a big washer behind that bolt, it cannot fall, it's too big. Pretty easy job overall.

@jamesb1988 Жыл бұрын

@ProjectTimeGarage Already took care of it, you're right it wasn't bad at all! Plus it gave me an excuse to clean up my grimey a** fuel bowl while I had it removed... man, with the new pump in, talk about a massive difference! Makes me feel a little better with regards to stripping the threads out on the old one that it was getting pretty tired regardless.

@DavidGibson-qo3nj 11 ай бұрын

Where can I get the ladder with the platforam do they sale them ? Any help plz ty

@ProjectTimeGarage 11 ай бұрын

This is the one I'm using. amzn.to/3Zdxi20

@carlospadilla9576 2 жыл бұрын

I am getting fault codes from my oil pressure switch failure and icp sensor I switched them both out and my IPR and all wires are good could my Oil pump be going out any suggestions

@ProjectTimeGarage 2 жыл бұрын

It may be worth checking the low pressure oil pump. If it isn't sending enough oil up top, then the High Pressure pump will not be able to generate enough pressure. Start with an oil pressure reading with a manual gauge on the LOW pressure side. If that's good, then the IPR/HPOP are the next most likely culprits.

@dannygarzona9574 2 жыл бұрын

Big red

@ProjectTimeGarage 2 жыл бұрын

Good name. Thanks!

@Content7.3 Жыл бұрын

Is that new icp sensor a motorcraft or after market? I’m curious if aftermarket, how it’s performing. I’ve had bad luck

@ProjectTimeGarage Жыл бұрын

I learned years ago that Motorcraft/International was the only way to to. So far I've never had an OEM one fail on me prematurely.

@Content7.3 Жыл бұрын

I have learned it the hard way. Every aftermarket sensor has failed on me

@WaynePacheco-s7i Ай бұрын

How many times did you have your crank it before it turned over?

@ProjectTimeGarage 20 күн бұрын

It takes a bit to refill the oil system. Maybe 45 seconds to a minute.

@Burkules47 10 ай бұрын

I noticed that your buddys truck is an early 99 like mine. Which hpop did you guys go with and did you go with the later version 17 degree hpop or the 15 Degree hpop that came on thos earlyy 99's

@ProjectTimeGarage 10 ай бұрын

He went back with the absolute bone stock pump for 99

@Burkules47 10 ай бұрын

Gotcha... I saw the icp readings on the video and that thing puts out good pressure. Gotta replace mine soon

@T-Eazy90 2 жыл бұрын

What size is the bolt on the pump drive gear??

@ProjectTimeGarage 2 жыл бұрын

18mm I think.

@brandon22333 2 жыл бұрын

A little late but does any oil drain from the reservoir? I’m getting ready to replace this on my truck and want to make the smallest oily mess possible lol

@ProjectTimeGarage 2 жыл бұрын

Most oil drains from the reservoir, yes. It'll take a while to start the truck.

@brandon22333 2 жыл бұрын

@@ProjectTimeGarage thank you

@atv55803 11 ай бұрын

suck it out of the reservoir you'll have oil everywhere if you don't

@prmcollin Жыл бұрын

Red Dead Redemption

@ProjectTimeGarage Жыл бұрын

Good stuff.

@NoWay-xu1ie Жыл бұрын

What kind of Hpop are your installing. Also do you have a recommendation on high pressure oil lines and does adding the crossover line make a difference ? Thanks for the video.

@ProjectTimeGarage 11 ай бұрын

The pump is an OE Bosch pump. For pressure lines, I would probably stick with OEM Ford/Navistar.

@JaceDasher 4 ай бұрын

What on the pump can tell you its bad i removed mine and want to rebuild it but im trying to disassemble it

@ProjectTimeGarage 4 ай бұрын

Low reading on the High Pressure Oil system during hard acceleration. Basically floor it and make sure you have 2,500 to 3,000psi of high pressure oil. If the pressure drops off quickly, or doesn't build that high then the pump is a suspect.

@805coastin7 3 жыл бұрын

Was that an OEM Hpop or a modified type?

@ProjectTimeGarage 3 жыл бұрын

OEM

@7.3clan41 5 ай бұрын

What brad is your Hpop?

@ProjectTimeGarage 4 ай бұрын

Bosch - Same as IH/Navistar/Ford used from the factory.

@StephanieStewart-pj5yb 9 ай бұрын

What after replacement truck wont start

@ProjectTimeGarage 9 ай бұрын

It takes a LOT of cranking to get oil back into the High Pressure rail.

@carlospadilla9576 2 жыл бұрын

What brand of oil do you recommend

@ProjectTimeGarage 2 жыл бұрын

I'm probably not qualified to recommend oil, but I use Shell rotella t4

@carlospadilla9576 2 жыл бұрын

@@ProjectTimeGarage how about oil pump what brand motor craft

@wenzelsstoneponyequine3667 Жыл бұрын

Call it MAGA red

@ProjectTimeGarage Жыл бұрын

Hell yeah!

@rodivis1226 2 жыл бұрын

Clifford!

@rodivis1226 2 жыл бұрын

the big red dog!!

@ProjectTimeGarage 2 жыл бұрын

Love it!!

@johnnicholas7783 2 ай бұрын

Liberty

@ProjectTimeGarage 2 ай бұрын

That was my suggestion too. He ended up naming it Fancy - After Reba McEntire's song Fancy.

@craighunter3345 2 жыл бұрын

I think Clifford works great for this truck

@ProjectTimeGarage 2 жыл бұрын

Thanks for the input!!

@marshahelms3426 Жыл бұрын

I agree it should be Clifford 😂

@markmcintyre3844 Жыл бұрын

My vote is red rocket 🚀 lol

@ProjectTimeGarage Жыл бұрын

Love it!

@craigcricket7932 Жыл бұрын

Thank you. I have the same truck. 1999. The only year they put, V8 tag on the front of the front fender. Mine is a 6 speed manual. I crank it endlessly. Won't start. I put battery charger on it, and a shot of starting fluid in the air filter box. Then it starts. Could it be my, HPOP? I've had Injectors, Glow Plugs, Intake Wiring Harness replaced 25,000 miles ago.

@ProjectTimeGarage Жыл бұрын

First thing is first. You need to see what the high pressure oil rail is doing while you're cranking. HPOP is a potential issue, but so are a lot of other things. Basically, it sounds like you have to crank the truck a lot to get high pressure oil enough to actuate the injectors. Use a scanner and see what the HPOP is doing during cranking.

@craigcricket7932 Жыл бұрын

@@ProjectTimeGarage Thank you. It is an awesome truck. Im convinced, it's a ,"fixable issue". I'll let a Ford Dealership take a look. I'm second owner. Purchased 2014. It's as rust free, top to bottom, one could ever find. Interior has zero tears and very little obvious wear. No aftermarket performance upgrades. 225,000 miles.

@davidlampe4153 Жыл бұрын

New to your channel like this video content I have a 99 7.3 with 330k miles it’s kinda tired lacks power. Good diesel mechanics are getting harder to find how do I find a diesel mechanic who won’t rob me?

@ProjectTimeGarage Жыл бұрын

Man, finding good people is hard to do. My advice? Get with a local diesel club and find out who they use. There are a couple in this area that are very good, if you're in the Nashville area.

@lawrenceborrego2928 2 жыл бұрын

Clifford should be the name

@ProjectTimeGarage 2 жыл бұрын

Yeah, Clifford was definitely in the running - in the end, he chose Fancy. Because of the whole Reba McEntire, redhead, and hoping it won't let him down, lol.

@uriahadriance461 3 жыл бұрын

Old red

@ProjectTimeGarage 3 жыл бұрын

Old red, nice.

@jeffkoshen9906 2 жыл бұрын

Red fury

@ProjectTimeGarage 2 жыл бұрын

Good name!

@Seahorseequestrian 3 ай бұрын

Name it OL Red

@ProjectTimeGarage Ай бұрын

Sounds right.

@richiegonzales6750 Жыл бұрын

Red Fred

@ProjectTimeGarage Жыл бұрын

Cool!

@demarcusross3619 11 ай бұрын

Torque specs or German torque

@ProjectTimeGarage 11 ай бұрын

Yep, Gutten-Tight!

@kipsvr6257 Жыл бұрын

How much do you charge for that job?

@kipsvr6257 Жыл бұрын

Nd how long does it take to change?

@ProjectTimeGarage Жыл бұрын

Plan for about 3 hours or so if you've never done one.

@kipsvr6257 Жыл бұрын

Ty would you charge a person 1600 dollars to change the pump?

@ProjectTimeGarage Жыл бұрын

@@kipsvr6257 That seems excessive to me. The new pump is usually around $600 or so. So that leaves $1000 in labor. Not a $1000 job in my opinion.

@troybittenbender5828 Жыл бұрын

america

@ProjectTimeGarage Жыл бұрын

'murica

@feistyfossilerfamily6037 7 ай бұрын

Name the truck Ring

@ProjectTimeGarage 6 ай бұрын

I'll pass that info on.

@BroncosFan303 Жыл бұрын

Call it orange

@ProjectTimeGarage Жыл бұрын

Cool, thanks!

@themechanicman3865 Жыл бұрын

You failed to show pulling the gear off with the bolt how you set your timing with that gear cuz there's little dots in there you failed to show any of that when pulling it apart

@ProjectTimeGarage Жыл бұрын

Never seen any dots on the HPOP gear of any 7.3. No such thing as timing the pump. It's not an injection pump, it's just an oil pump.