我繞的內轉無刷馬達，就是看你的影片學的，真的好好了解，又好的方法，隔了11年又在出現這影片

I purchased this motor from our local hobby store years ago, installed it into one of my R/C trucks and had fun, all of a sudden ...... POOF!!!! It burned out, so i thought to my self, why not fix it.... So after reading a bit on the internet before atempting this endevor, i got down to it... And blammo it worked. Better than the original motor , i was happy and sticky from the fiberglass resin i purchased from canadian tire, i think . O. Happy days are here again. For thoes who do this type of repair, its not critical on the fiberglass resin type , its only used to coat the winding to provide an insulation barrier and keep the wires from moving.

Very simple and direct. Well done. Thank you. Next time, please add details like the kind of resin you use, the length and diameter of the wire. The Penn and Teller was a nice touch. :)

OK, High heat epoxy is used to coat the metal as an insulation, so at the point of actually winding it the wire insulation does not get scratched off and ground out .. the windings wire used can be anything, i just copied the original length, and total diameter of the original..... it was easier to twist them together as this made it easier to rewind it... were only rewinding so there is no need for balancing the motor. i still use this motor today :)

Most brushless motors end in a .5 winding as the coil starts and ends on the opposite side of the arm. Yes you can wind a 17.5 with any wire you can find that fits in the atrea, also look at the ohms / resistance per wind and see if the esc can handle what you intend to create.

with dethklok playing in the background any motor rewind should kick ass!

fantastic video thanks!

Good Work, Thanks so much for sharing this video!

Well done!

Great video! How does it change the properties of the motor to combine and twist the wires together? It seems 10 short wires rather than 1 long wire will have a significant effect. Higher current / RPM and less torque? I really do like the idea of wrapping multiple wires at one time! Thanks in advance!

The last rasin you applied is to replace the burnt out plastics? Great video!!

Great video, I have an inrunner sensorless motor that needs to be rewinded. Can you show how to do that? Thank you

Спасибо за видео.

cool video man your the first i have seen use this twisted wire and i watch over 14 hrs a day studding cool as

How do you separate the can and motor for rewinding? I have a hpi brushless sport tuned JR motor? Any reply appreciated thanks from Australia!

Can you rewire a 17.5 motor? I've done a bit of research, and haven't found too much on the specifics on how to wire a motor like is required.

where did you git your copper wire spool, what gauge wire, how many strans or wraps do you use?

Those 3 winding coils, are they the same winding direction ?

what type of wire did you use

Awesomeness I have one I need to rewind how can I learn more about this process?

Very interesting and informative video! Was that an old novak motor?

hi tracar1 i hope you dont mind if i ask a question.. why are some 13.5t motors have 4 wires in it with different wire diameter?

where do you get the wire and what kind of resin is that .

what is the goo that you apply to the stators to coat them (the 2-part insulation that you put the 'kicker' into?) thx for the vid! Also is there an alternative insulation that i can use if i cant find CA glue or whatever you use? What about epoxy coated on with a brush and then sanded off the outer surfaces?

Would the wire that is not spun have more room for more wire ??? Would rolling the twisted wire between two planed boards decrease the diameter ?? How you can answer the questions.

love Rush Limbaug!..great Vid....btw, so there is no need to balance the motor?

Impressive. +1

Does it better to use thicker copper wire on winding brushless motors instead of stranded wire? Does the thicker copper wire increase the durability of the motor?

METALOCALYPSE for the win!!! Good tutorial too :)

nice video

Btw, thanks for taking the time to shoot this video..

I watched to the end only to make sure you didn't hit your thumb cutting towards it LOL

nice transformer

Ironically, I bought a super-cheap, but essentially useless, 3.5-turn Swift motor (10,000kV) which looks exactly like the one you're rewinding! I'd like to rewind it to 21.5T or thereabouts for stock 540 performance, but do you have any idea if it's a single-strand on a 21.5T motor? Also, it's not super-clear, but on your motor does each 5x strand go around each armature pole, or do they "criss-cross"? Thanks!

And why to rewind the motor if it works well? do you gain something better if you rewind it? and how is that achieved?

how did you clean the stacks before rewinding them?

it is fiberglass resin , mixed with peroxide hardner to cure it

impresionante trabajo pulgares arriba

Judging by the winding this motor is going to give a hell of a performance. Sensored bldc. High, low speed torque i guess.

Hi there.How about the temperature of motor under load?

Lol @ Alex Jones in the background!!

what material which you used in furnishing the stator?--I mean isolate the stator?

Can u rewind my losi xcelorin 21.5 turn crawler motor for me

How thick copper wire you used? And is it possible to wind 7.5T on 4.5T TrackStar motor?

Qual o modelo é esse motor?

Please make big bldc motor for air cooler lowest amp & high rpm🤘

do you have a how to video on building a dc motor from scratch or a bldc ?

so what gauge wire are you using? i didn't realize the three wires go to a plate like that. that means this motor is working off of Y 3 phase correct? do motors that are not a .5 like just a 10 rather than 10.5 have this plate?

What can we make a esc for BL dc motor at home

How do is the resultant speed and torque of a rewound motor calculated? I'm working on a project that requires small but very powerful BLDCs, and I'm not sure where to start looking.

What is the stuff that you were covering the wire with??

As the title explains its about rewinding a motor, but if you have other questions, ask away.

Please, how do you remove the clear insulation on the winding wires prior to soldering them?

I've never seen a stator of that kind 🙄which motor is it from

PLEASE ANSWER! WHAT GAUGE OF WIRE WERE YOU USING?

สุดๆๆๆๆๆ

👍👍👍

Extra!

katalis resin jadi pelindung ya ter 🙏😀

dude. I heard metalocolypse in the background!

i have a table saw motor, the grooves on the inside of the stator, mine are ruined, almost slick as glass, motor overheated, got so hot almost melted the coils, carbonized the wood that got in between the armature and stator, and sanded the grooves on one side almost slick, melted the thin sheet plasic insulators that wrapped the sides of the coils, complete burnout. cant find the exact replacemenat motor, and they dont make parts for it, i called kobalt, no parts or motor available, if warranty is up, throw it away, their exact phrase, im gonna try rewinding it, but i noticed on one side of thecoils, there are no more grooves, how does that effect it, i know juice has to flow thru there, and the grooves get shallower and deeper depending on the distance from the armature, by reading, i gather they are slightly out of round, like i said i read where the grooves get deeper and shallower, but how will it effect its performance?, is there any hope? or is it a complete waste??

winner ECS se chalne wali brushless motor Bana kar dikhaye

What gauge is the magnet wite?

What's about left side corner 😄😄

tony: most of us when we reach adulthoood understand that most things areaproximate in life,, we are not robots , we are human, so when i say about 12 its a good guess, i could use 4 ,or i could use 20, if your going to bitch and complain about a product i did not create, do the right thing and read the manufacturers instructions

how many stator poles bldc motor needs?

Finally

Nice now i try. LOL something to do this weekend. Rebuild motors. Haha

i think i used 28guage and 3 wires twisted into 1

3 circuits. Do you know how many kv?

i think every motor just have two side cable (positive and negative). then why there is three cable in this motor?

@ 2.38 sun glasses for cats?

có người viet Nam nào.che nhu zaj dược hok.lam clip hướng kj thêm xju dược hok.m.n oi

bahaha sunglasses for cats

Wouldn't the resine melt

Hotspot

bapu

nice video please can you help me i wanna build control microbrushless motor without PIC

Have you ever explained what you are doing vocally and what product you used other than 12 drops i think. I watch you-tube movies so I can learn how to fix myself. But after watching your video Iam even more at a loss. Try using your vocal cords a little more .

?wow..nice?..good job..rewind?.:) :p

by

The motor at the end wasnt the same motor,, u just wasted my bloody time taught you was gonna be usefull

What is the stuff that you were covering the wire with??