Thank you! Five minutes of work and saved about $75 for another arm. I won't be pushing piled up snow anymore with the arm.

You're a big help, Rich. Your solution worked perfectly.

Thanks for the video. When my wipers quit moving my mind was filled how to take it a part and how much it would cost me. I took the arms off and the smooth splines looked ruined. Your video saved the day and money. I cleaned the up and so far so good.

You saved from going down a rabbit hole. A sincere thank you.

I didn't know Peter Griffin had a car repair channel

Yep. My blade was frozen. I was on my way to the garage, but u saved my day. Big thanks.

This addresses the exact problem on my van. Thanks!

👍 Dude, thank you for taking your time in sharing your experiences. This info has helped. One wiper blade has stopped operating from my car and followed your advice, it worked very well. One Note: I found the wiper-blade's nut loosed when removing the cover. I still cleared the ridges and reset. Did it on both just to get it over with. All Good now!

Thank you! I'll give that a try tomorrow. 👍

Thanks, my wiper arm just failed on me during a downpour. Drivers side to boot! Gonna use this info to fix it once the rain lets up, THANKYOU!

It worked. It took 5 minutes. I used a sharp kitchen knife. Thank you.$$$

Excellent channel 👍🏻

This helped alot, mine were completey filled with dirt and metal, they work for now, but I have to order new wiper arms too. Thanks for this video, saved me a lot of money.

Great video.it saved the day on my 2004 Nissan Xterra. It also saved me 90 bucks .i would have replaced it

Chevy Ventures have that problem a lot. Good tip.

Great valuable advice 🤘🇬🇧

Thanks for taking the time to explain this!!

Thank you!

Thanks, good idea! helped for now..

Thanks for the info!

Nailed it! Thanks Rich.

Thanks for sharing

Worked for me than you so much!!

I have one that stripped out. Plus it’s starting to sprinkle today. Thanks for the easy fix. 👍

Literally a lifesaver, thank you

Thank you soo much I can’t imagine what I would have been charged to get this fixed!

Thanks for the great video I just finished my 2014 nissan pathfinder had the same issue

Thanks you bro help me in 2020

I started my Saturn up one winter morning this year and the driver side wiper just fell onto the ground. Thing evidently rusted through. Had to get one from a u-pull.

awesome

Thank you...

Also if you don't want to buy new arms and you even this fix doesn't provide perfect grip - very soft wire. If you have very soft wire lying around, you can use it to make it fit better.

Do I need to replace the arm if the threads are stripped out ?

Thank u

Dissimilar metals in a water environment, no wonder they fail. I see the weaker metal, the aluminum, is designed to fail first, so the repair is easier than if the male end stripped out.

USE A WIRE BRUSH

This is exactly what I am dealing with today. Thanks. It seems that the lost aluminum material would need to be replaced??? Inside the hole of the wiper arm; the metal has been worn smooth by the spindle. Could one add a metal resin, or coat it with a thin layer of something like JB Weld???

What if both wiper an the teeth on the bolt are stripped? Is there a way to save this or have to buy a whole new motor?

Hi. When reinstalling the new wiper arm do you drive it down on to the spline or just tighten the bolt?

Hey Richpin do you have any replacement arms for the driver's side? I will pay you if you get this message.

I've just replaced the linkage on my car and now the sweep on the driver wiper is a bit too long, my wiper hits the a piller and the lower seal. The linkage is straight so I think the aftermarket part is a bit long and I don't think the sweep can be adjusted, can it?

What is that part called

I'm supprised that the splines will drive the aluminium, i would of expected you to need to wrap the splines with 1 to 2 turns of ptfe tape or tin foil to take up the room.

What size nut? Hello?!?

I wonder why car manufacturers haven‘nt figured out a better design for this. Like maybe use a stronger material instead of aluminum so they wont strip as easily. I have had two older cars and both of them have (partially) stripped wiper arms. Definetely a common thing in colder climates and people don‘t know these arms work so they use them as snow plows in the winter and strip them out. But the biggest problem was for both of my cars i could‘nt buy these arms new anymore otherwise it would be no biggie.

No amount of scraping out excess metal could fix my problem so I just ran my drill through the arm and post screwed in a black sheet metal screw works fine now. Easier and cheaper than replacing the wiper transmission. Good idea though just wouldn’t work for me.

Does this mean that after you clean the splines, that you must buy a new wiper arm? Or is it OK to reuse the old arm and it will grip?

Somebody lifted mine up and I can not unlock it. Scared to berrak something. How do I unlock it and bring it to normal position? Thanks

I bought me a use truck but just one wiper work.

I have to do this by -40...

Does anyone know if arm labeled left hand goes on passenger side or driver side?

Could I put loctite on the grooves?

My problem is the arms under the hood. Keeps detaching so they don't move.

What if the bolt above that is stripped??? Not the arm, but the bolt itself?

Wire brush is way faster....🤘

This guy has a Boston accent 😂

Windshield keep hitting

Wait is this everyone loves Raymond speaking?

Tedious!!!

I drove my car to an auto store to address the issue, which cost me 110 dollars, F* I should have seen ur video first!

took a little over 3 minutes to do absolutely zip. If it's stripped, cleaning the splines out doesn't do anything but waste time going nowhere. don't watch the whole thing folks, find another video channel and hope they are at least 2% smarter.

☠️