How to DIGITIZE 3D Puff Without Any Hassles

Рет қаралды 107,377

3 жыл бұрын

Willy’s got ANOTHER awesome digitizing tutorial for you in this new Embroidery Hub episode, but this time, he’s showing you how to digitize for 3D puff embroidery on a cap. But that's not all because once he’s done with the digitizing, he’ll embroider the cap for you on the Ricoma MT-1501 in order to show you the entire process from start to finish.
Learn to digitize and embroider a patch here:
• Patch Embroidery From ...
Check out Chroma digitizing software here:
ricoma.com/US/software/chroma
Watch Willy break the world record for thickest 3D puff cap embroidery: • WE BROKE A NEW RECORD!...
Watch RICHARDSON CAPS 3D Puff Embroidery Challenge:
• RICHARDSON CAPS 3D Puf...
Watch our digitizing tutorial for small letters on caps:
• 4 Tips to Master Small...
Learn more about the machine featured in this video: ricoma.com/US/machine/mt-1501
Facebook Embroidery & Custom Apparel Mastery Group: / embroiderymastery
Join the Ricoma newsletter for educational blogs, videos, and live webinars: info.ricoma.com/newsletter
To learn more schedule a virtual demo today: ricoma.com/US/virtual-demo
Get our latest Ricoma embroidery KZfaq videos sent straight to your Facebook Messenger: manychat.com/l2/RiCOMA.us
To learn more about our embroidery machines, visit our website: www.ricoma.com
In this tutorial, Willy uses both Chroma Inspire and Chroma Luxe to show you how to digitize for 3D puff, so no matter what version you have, you can easily follow along. With Chroma Inspire, creating a design of this nature should take about 10-15 minutes. However, with Chroma Luxe, it could take as little as five minutes to digitize this design, thanks to Luxe’s wand tool.
In addition, you’ll learn just how 3D puff digitizing works as well as plenty of tips on how to keep your digitizing clean and crisp within the software. Willy also explains why 3D puff requires a satin stitch and teaches you how to adjust your angle lines and split lines to make sure your stitches are going in the right direction.
After showing you how to make your stitches start from center outward-a necessity for cap embroidery-Willy covers the following steps in detail: removing the underlay, adjusting push and pull compensation and adding a nap blocker. Once the digitization is complete, he takes this tutorial to the craft room to test his design, which we think came out great!

Пікірлер: 184

@amyhughes8739 Жыл бұрын

This was an awesome video. I do not have the Ricoma but your tips and tricks are wonderful. Thank you so much.

@ricomatv Жыл бұрын

We are so glad our tips helped, Amy!

@Dynamics556 3 жыл бұрын

I understand a little more about the software. Love it easy to understand. I am a website developer so I am glad this software is friendly and easy use

@ricomatv 3 жыл бұрын

Great to hear! Thanks for watching!

@larryransaw6362 2 жыл бұрын

I’m learning a lot from you...Thanks for the tutorial

@ricomatv 2 жыл бұрын

You are so welcome!

@mensembroidery722 3 жыл бұрын

Very nice work. It‘s perfect 🔥

@ricomatv 3 жыл бұрын

Thank you! And thanks for watching

@darealjbeatz 3 жыл бұрын

Great video thanks for sharing

@ricomatv 3 жыл бұрын

Thanks for watching!

@baavproductions 2 жыл бұрын

This is a great video!

@ricomatv 2 жыл бұрын

Glad you enjoyed it!

@jonesherbington997 Жыл бұрын

Thank you this was great stuff.

@ricomatv Жыл бұрын

Glad it was helpful!

@BIGCMC100 Ай бұрын

Thank you for this video. Good stuff

@ricomatv Ай бұрын

Glad you enjoyed it!

@leviteapparel 3 жыл бұрын

This is fire I can't wait to get approved for financing so I can get this machine

@ricomatv 3 жыл бұрын

YES! We can't wait for your to get your own Ricoma either!

@kevinpeguero1176 3 жыл бұрын

Great video! Have your ever embroidered 2mm puff on a trucker hat foam panel? If so, what tips/tricks do you have?!

@ricomatv 3 жыл бұрын

We've done some crazy projects with trucker hats and 3-d foam, check out our video where we do three layers of 2.5mm foam: kzfaq.info/get/bejne/a8hjlrWpnMimimQ.html&t

@mindsetmanagement2893 2 жыл бұрын

Thanks for this video

@ricomatv 2 жыл бұрын

Most welcome!

@nissanpatrolgr.y6027 3 ай бұрын

Amazing ❤❤❤

@ricomatv 3 ай бұрын

Thanks for watching!

@faychildress 3 жыл бұрын

I understand more about how to get the embroidery to start and stop. I have PE Design 11 software and it is very different. I could not figure out how to make it do the things that I knew I needed to do the 3D puff. I hope to adapt this to my software. I wish my software was as easy to use as this one. Thank you for the tutorial.

@ricomatv 3 жыл бұрын

Thanks for watching, if you're interested in our software, you can click here to learn more: ricoma.com/US/software/chroma

@drmiteshtrivedi 3 жыл бұрын

That is sick

@ricomatv 3 жыл бұрын

Thanks so much for watching!

@msabarez 2 жыл бұрын

That's awesome video! Did you adjust the height of the needle for 3D portion? Thanks.

@ricomatv 2 жыл бұрын

Hi Mel! Check out this video in which we show how to do puff embroidery on hats. kzfaq.info/get/bejne/id51qKaQl5nWmKs.html

@Bakerfamilyvideos 4 ай бұрын

I love this video

@ricomatv 4 ай бұрын

Thanks so much for watching! We are so happy you enjoyed this video :)

@CapricornDaze Жыл бұрын

Hey Willie. Your videos are always so informative. Thanks. What size needle should be used for 3D puff? I'm on a single needle machine. I'm guessing it's 90/14 sharp?

@ricomatv Жыл бұрын

Hi Regina! You can use 75/11 needles and running their machine at 600

@user-uc3ps8vz6z 11 ай бұрын

Hello and thank you for this awesome video, it really helps. How do we correct the space left on the border of the yellow - it reflects under your finger at the end of video? If that happens again - what do we do to correct? Also, what needle should we use for this type of work? Again, thank you so much!

@ricomatv 11 ай бұрын

Hi there, please send our customer service team an email so they can help > service@ricoma.com

@heyyou4089 3 жыл бұрын

Awesome vid! Super helpful. Can you explain a little about push and pull? I get what it’s for but how do you know what to set it at? Thanks!

@ricomatv 3 жыл бұрын

Sure thing! You can learn more about push and pull in this chroma digitizing video: kzfaq.info/get/bejne/rpaWaMaV1JnPf5s.html

@kygoeken6075 Жыл бұрын

Push and pull is a way of thickening up a piece of artwork and adding overlap where there are split lines to prevent seeing the background or material behind the embroidery. Whatever the direction the stitches are going, if you add to the push/pull it will extend the length of the stitch thus covering the gaps I referred to. You can adjust it in increments of MM, or percentage.

@dannythemusiciancrafter3280 3 жыл бұрын

Hi! Aren't you suppose to capping the edges to cover the edges and to stop the thread unravelling?

@Yshral Жыл бұрын

yea I dont think they showed that part trying to make digitizing seem easy

@tbzdezigns6113 11 ай бұрын

Just as helpful as him not mentioning it.

@valeriaknight9917 3 жыл бұрын

Really detailed explanation! Thanks

@ricomatv 3 жыл бұрын

Glad it was helpful!

@edvclothing9840 2 жыл бұрын

Hello great video Did you change the speed once you put the foam and if, what is the speed you put the machine at thanks have a great day.

@ricomatv 2 жыл бұрын

No the speed auto adjusts when it’s doing jump stitches for the 3D part

@edvclothing9840 2 жыл бұрын

@@ricomatv cool thanks

@Roy1271 3 жыл бұрын

Hey Willie, How do you make your source files? I would be cool if you provided a file for use to follow along.

@ricomatv 3 жыл бұрын

That's a great idea! Thanks for the recommendation

@annaliseprimus4025 3 жыл бұрын

Hi, what is the size of this design? Very helpful video, thank you!

@ricomatv 3 жыл бұрын

Thanks for watching!

@renevoyage 2 жыл бұрын

Thanks for the video what is the diameter of the needle and thread to embroider the satin?

@ricomatv 2 жыл бұрын

Hopefully this video helps! kzfaq.info/get/bejne/ZrGYeN1hp7fInqc.html

@ThreeLittleKids Жыл бұрын

Hi! Do you have this design for free to share so I can try to embroider on a cap? Am waiting for my EM-1010 to arrive and have never embroidered caps before. So excited!! Need to practice on machine first and then Chroma!!

@ricomatv Жыл бұрын

Hi there! You can actually find some cool designs through Hoopmade ----> hoopmade.com/

@HarryPotter-dg5qw 11 ай бұрын

Great video! Is that software online base?

@ricomatv 11 ай бұрын

Hi! Yes, you need to download it and have a serial number

@jamesjasiuk5428 2 жыл бұрын

Can we please see you work with the TC-1501. It looks like most videos you do are with the MT 1501. I have the TC-1501 and it would be nice to see you using it in some of your videos. Thank you.

@ricomatv 2 жыл бұрын

Will do! Thanks for the recommendation. for now make sure to check out some of our older videos, we have plenty projects using the TC 1501 kzfaq.info/get/bejne/bLKIicyIxtLXf4U.html&t

@gostitch72 Жыл бұрын

what hoop choice do you choose for cap "on chroma" for ricoma machine?

@ricomatv Жыл бұрын

Hi there! Please send an email to customer service so they can help! ----> service@ricoma.com

@njzstore7835 3 жыл бұрын

Can I do it with chroma inspire? There’s some tools like utilities that I didn’t find.

@ricomatv 3 жыл бұрын

Hi there, you can do pretty much anything with Chroma inspire, but the tools used may differ, if you need help with chroma inspire, contact our tech team: ricoma.com/us/tech-support

@zehcnas1008 Жыл бұрын

Do you have to cap the ends? I noticed that you didn’t do that. Thanks for a great video.

@ricomatv Жыл бұрын

Hi Lillian, thanks for the suggestion, we will be sure to pass this down!

@dreammaker2344 3 жыл бұрын

So with this machine you don't need to add cap threads at the ends of each letter to do 3D puff?

@ricomatv 3 жыл бұрын

hi there, with our embroidery machine, once the design is loaded on the machine it will embroider automatically without stopping unless you add the stops to your design. for more help with 3d puff, you can contact our tech team, ricoma.com/us/tech-support

@edgarzamora7553 2 жыл бұрын

Where do you order your stitching thread do you have a site where I can order it from

@ricomatv 2 жыл бұрын

We recommend for you to check out our Ricoma blog which offers a variety of tips, and resources. We have linked it below! blog.ricoma.com/2019/06/06/top-10-wholesalers-for-all-of-your-embroidery-needs/

@redteamshirts Жыл бұрын

Great video, but the front sides of the hat got squashed in a little bit.(just outside of your stitch. Left of the "t" and right of the "k") how do you prevent that?

@ricomatv Жыл бұрын

Hi! We recommend speaking with our customer service team so they can give you some tips/tricks to prevent that! ----->service@ricoma.com

@mrdinhobass Жыл бұрын

Goodnight! I am a ricoma customer and I recently acquired a TC 1501 here in Brazil. I would like to know how can I purchase the CHROMA program?

@ricomatv Жыл бұрын

Hi there, and congrats on your new purchase! Please submit a form with the team, so they can get this started for you!--->ricoma.com/US/contact-us

@ThePuddingchannel 2 жыл бұрын

can you use the digitizing programme on a brother machine? looks like you can't convert it to a .pes file

@ricomatv 2 жыл бұрын

Hi there, thanks so much for watching. This is a great question to ask in our Facebook support group, Embroidery and Custom Apparel Mastery. This group is meant for all lovers of embroidery with lots of resources and more members discussing topics and helping each other out and learning about Ricoma machines and other brands! We recommend you join this group as we'd love to have you! facebook.com/groups/embroiderymastery

@tuandinh9992 5 ай бұрын

Can these tips be applied to the 1501 tc machine?

@ricomatv 5 ай бұрын

Yes

@TrapLabIslanders 2 жыл бұрын

🔥🔥🔥

@ricomatv 2 жыл бұрын

Thanks for watching!

@TrapLabIslanders 2 жыл бұрын

@@ricomatv I need a ricoma channel. Can you help with this?🤔

@biblican911 2 жыл бұрын

Sounded like you slowed machine down during foam… What did you do to clean up foam on edges?

@ricomatv 2 жыл бұрын

Heat gun

@SaboorWarsi Жыл бұрын

please make the detailed video on travelling please

@ricomatv Жыл бұрын

Hi there, if you wanted some tips/tricks please reach out to the service team so they can walk you through our Chroma software ---> ricoma.com/US/contact-us

@vhinkle3 Жыл бұрын

Willie, how do you get the picture (Think) into the software to begin with?

@ricomatv Жыл бұрын

Hi! You create this design on Chroma, and then send it to your machine!

@vhinkle3 Жыл бұрын

@@ricomatv but where did "Think " come from? Adobe? Corelli? I want to make a picture of my own and then convert it to an embroidery design.

@vhinkle3 Жыл бұрын

Corel, sorry.

@rosie6156 3 жыл бұрын

My husband and I bought a Brother entrepreneur pro px1055. Few months ago and the program we have is mysewnet.we we do not understand how to use it. We would like to do our own designs. We need help. Thank you for your time

@ricomatv 3 жыл бұрын

Hi there, we typically teach digitizing on our own software chroma, but you can find lots of cross over when it comes to the basics of digitizing. Perhaps our digitizing KZfaq channel can help, you can check it out here: kzfaq.infovideos

@richardlopez5992 3 жыл бұрын

Get yourself pe design 10 or 11 it’s not hard to use and learn to use and many tutorials on KZfaq for it

@eugenew4456 2 жыл бұрын

Hi, i have a Ricoma 1501TC-7S. I'm new to it. Can i send an artwork for it to be digitized for use? Outsource from you

@ricomatv 2 жыл бұрын

Hi there, we are not a digitizing company, but we do have a list of recommended digitizers if you're looking to outsource! email service@ricoma.com and ask for this document and they will send it over!

@cutflower36 3 жыл бұрын

Is the luxe compatible with PES files for brother machines

@ricomatv 3 жыл бұрын

Chroma allows you to export your design in any format including .PES

@BaconGod14 3 жыл бұрын

Hi. I love watching you videos you give great information but I've not got this software or machine. I have a Brother pr 1050x and pe design 11. Do you know anyone like yourself who does theses kind of videos for that machine that I have. Thanks

@ricomatv 3 жыл бұрын

Not that we are aware of. This is the premiere destination on KZfaq for all things custom apparel! A lot of the concepts will apply so you can still have a lot of takeaways

@BaconGod14 3 жыл бұрын

@@ricomatv Thanks for your reply

@user-yv9sh9sb3m Ай бұрын

Do you have to put underlay under your puff?

@ricomatv Ай бұрын

No. When doing puff, the underlay should be removed.

@kimrie26 3 жыл бұрын

My software for some can’t add angle lines. Nor does it have the wand option. I have the chroma inspire. Please help

@ricomatv 3 жыл бұрын

You’ll need higher tiers like Chroma Plus or Chroma Luxe to unlock those features

@kimrie26 3 жыл бұрын

@@ricomatv that’s probably why. thank you 🙏🏼

@cherriekinsey8529 3 жыл бұрын

Where do you get your thread from?

@ricomatv 3 жыл бұрын

Hi there, thanks so much for watching. We recommend Madeira thread. You can check it out here > www.madeirausa.com/

@markblazek6271 3 жыл бұрын

Do you have a copy of the Think design

@ricomatv 3 жыл бұрын

Hi there this design should be made available on Hoopmade.com soon! you can also check Hoopmade.com for past embroidery hub designs.

@enderteran3044 2 жыл бұрын

Muy buenas tarde amigo acabo de comprar la máquina Ricoma con el programa para digitalizar pero necesito un conseguir un video donde explique cómo digitalizar pero en español por favor necesito de su ayuda

@ricomatv 2 жыл бұрын

¡Hola! ¿Has contactado con nuestro equipo? Puede comunicarse a través de este enlace. ricoma.com/US/support

@insideshowbizjourneyagains73 2 жыл бұрын

Can I digitize using my Photoshop software?

@ricomatv 2 жыл бұрын

No unfortunately, you need a digitizing software, since the machine is going to need to read the design in stitches.

@Coupella 2 жыл бұрын

Is there a reason why the K is split like that? Seems kinda weird the l part isn’t continuous.

@ricomatv 2 жыл бұрын

It's how we designed it to look like handwriting. Thanks for watching

@lorenlopez4374 3 ай бұрын

Why my Ricoma machine brakes the thread frequently if I put the speed more than 300?

@ricomatv 3 ай бұрын

That could be so many things: your thread path could be off, tension could be off, needle could be dull/burred, timing could be off etc.

@llijah7368 2 жыл бұрын

Can you perform these same actions on SewArt?

@ricomatv 2 жыл бұрын

Sorry, we're not familiar with SewArt. We recommend reaching out to the manufacturer.

@IDewsKustomz Жыл бұрын

What needle is used?

@ricomatv Жыл бұрын

Hi! You can use a standard 75/11 needle!

@cybertronkiller5733 3 жыл бұрын

do you deliver the machine to Northeast India??

@ricomatv 3 жыл бұрын

We have distributors all over the globe! Click here to fill out your information and your local distributor will be in contact with you, ricoma.com/us/contact-us

@lavanyar9497 Жыл бұрын

Hi sir how to use water soluble paper details information give me

@ricomatv Жыл бұрын

Hi there! We have this information on our blog, and a KZfaq video on this as well. Check out the links below! blog.ricoma.com/2019/03/15/embroidery-stabilizer-guide-tips-on-how-to-choose-the-correct-backing-for-machine-embroidery-2/ kzfaq.info/get/bejne/n7aTfcRpsbq6dKs.html

@bigkev6455 9 ай бұрын

What type of caps were used

@ricomatv 9 ай бұрын

We used these caps: Richardson 112 Hats

@Nallelibebe22 Жыл бұрын

What’s the purpose of an angle line ?

@ricomatv Жыл бұрын

It is important because the angle lines determined where the stitched are going to be placed. If you have too many of them it can create open spots on your embroidery.

@MiguelSanchez-pu2hm Жыл бұрын

what about letters like R that have the little opening?

@ricomatv Жыл бұрын

Hi Miguel! For more tutorials/tips we recommend looking through Chroma's KZfaq channel! ----->www.youtube.com/@ChromaDigitizingSoftware

@MiguelSanchez-pu2hm Жыл бұрын

@@ricomatv can you specify a video? it would be of much help

@yahayaosman2812 Жыл бұрын

How do you embroidery a large area's with multiple heards

@ricomatv Жыл бұрын

Hi! Are you referring to multiple heads?

@yahayaosman2812 Жыл бұрын

Yes please

@JAVIERCDELVALLE 2 жыл бұрын

WHAT FONT DO YOU USE?

@ricomatv 2 жыл бұрын

It's the Zulia Pro Regular by Sudtipos!

@AndreMercado Жыл бұрын

actually the font used is Ganache Basic

@JesseB1983 3 жыл бұрын

Lol! Not gonna lie, I sometimes feel like Tony whenever I hear about digitizing.

@ricomatv 3 жыл бұрын

Trust us everyone starts our the same way. You gotta start somewhere right? Good thing you've got us to help teach you everything you need to know!

@dzamora01 3 жыл бұрын

What's the name of the software?

@ricomatv 3 жыл бұрын

Chroma! You can learn more about it here: ricoma.com/US/software/chroma

@prosperugonna250 Жыл бұрын

Please how can install chromeluxe software in my desktop

@ricomatv Жыл бұрын

Hi there, please check out this video Chroma shared on their KZfaq channel--->kzfaq.info/get/bejne/hteldcmS0beYhYk.html.

@weslerseni3923 2 жыл бұрын

How much can I get this machine

@ricomatv 2 жыл бұрын

Hi Wesler! We recommend you contacting our sales team since our pricing can vary. ricoma.com/US/contact-us

@ericcastillo5248 3 жыл бұрын

Are going to share that file?

@ricomatv 3 жыл бұрын

Hi there, at the moment we do not have this file to share, but you can visit hoopmade.com for lots of our past files!

@QueenLolaBouli 2 жыл бұрын

Can someone recommend a good embroidery/print/patches company?

@ricomatv 2 жыл бұрын

We recommend you join one of our community groups where you'll find informative resources: facebook.com/groups/embroiderymastery

@QueenLolaBouli 2 жыл бұрын

@@ricomatv thank you! I will!

@ricomatv 2 жыл бұрын

@@QueenLolaBouli you're most welcome :)

@brothersofdestruction378 3 жыл бұрын

Can you do puff on a shirt or beanie?

@szondiezocks8579 3 жыл бұрын

Yes you can

@ricomatv 3 жыл бұрын

yes you can!

@Beany638 7 ай бұрын

Are tutorials only for luxe

@ricomatv 7 ай бұрын

Hi! Please check out the Chroma KZfaq channel > www.youtube.com/@ChromaDigitizingSoftware

@surajbhandari291 3 жыл бұрын

price??

@ricomatv 3 жыл бұрын

To learn about our pricing fill out the information in this form and our product specialists will be in contact with you, Ricoma.com/us/contact-us

@johndoeee888 2 жыл бұрын

Man whats the stitch count on that design ?

@ricomatv 2 жыл бұрын

Unfortunately, we don't recall! But it's awesome right?!

@edgarcarcamo1113 6 ай бұрын

Who can do a 3D custom digitizing?

@ricomatv 6 ай бұрын

Hi Edgar! This is a great question to ask in our Facebook support group, Embroidery and Custom Apparel Mastery. This group is meant for all lovers of embroidery with lots of resources and more members discussing topics and helping each other out and learning about Ricoma machines and other brands! We recommend you join this group as we'd love to have you! facebook.com/groups/embroiderymastery

@carlosbarajas382 3 жыл бұрын

What if the phone keeps sticking out

@ricomatv 3 жыл бұрын

Hi there, our service team can give you more pointers here: ricoma.com/us/tech-support

@vboss5801 Жыл бұрын

I have bought ricoma swd machine in india . unfortunately In india they dont give chroma software ,this very sad 😢.but your giving in united states . I have mailed about this please reply

@ricomatv Жыл бұрын

Hi there, this is only for the US, we apologize for the inconvenience.

@larryransaw6362 2 жыл бұрын

What’s the width and height on that logo

@ricomatv 2 жыл бұрын

HI there, thanks so much for watching. Height was 2.5 and width was about 5.0. Hope this helps!

@larryransaw6362 2 жыл бұрын

@@ricomatv thank you

@Yasr_98 2 ай бұрын

Do you sell this embroidery design ?!

@ricomatv 2 ай бұрын

Hi there! We don't have this sale design, but we recommend checking out HoopMade for other 3D Puff designs. hoopmade.com/

@Yasr_98 2 ай бұрын

How can i download chroma software free trail please ?

@zikhonandumiso3331 Жыл бұрын

MORNING I HAVE MACHINE HELP WITH TRANING PLS

@ricomatv Жыл бұрын

Hi there, please submit a request with the team so they can further help ----> ricoma.com/US/contact-us

@e2U Жыл бұрын

Don't you have a trace tool? by now 8-1-2022 ?

@ricomatv Жыл бұрын

Hi Jeff. We have a trace tool, and you can find it through our official website ---> shop.ricoma.com/

@SinseerProductions 8 ай бұрын

my density only goes as low as 10

@ricomatv 8 ай бұрын

Hi! Are you having issues with density?

@austinjamo9199 Жыл бұрын

Need in person training

@ricomatv Жыл бұрын

Hi Austin, we would love to help you out! Please send us an email so we can point you to the right direction ---->service@ricoma.com

@gamekingstudios 2 жыл бұрын

This is literally the only thing i dont like ricoma about. They give entre level software where you cant do simple stuff like convert complex fill to satin stitch. How do i follow tutorial when i dont have all the tools in a expensive machine package.

@ricomatv 2 жыл бұрын

HI there, thanks so much for watching. Our embroidery machine packages include everything you need to get started. Other embroidery machine manufacturers typically don't include any form of digitizing software. For more complex designs, you will eventually need to upgrade your software to Plus or Luxe. We do offer financing to help with your upgrade. If you're interested in learning more, please click here > shop.ricoma.com/products/chroma?variant=31414905077878