Wow, very nice video. Very professional and descriptive of how to repair/troubleshoot the RS800. Much appreciated!!
@jameslundy703 жыл бұрын
These Transmissions are pure junk, I paid a lot of money to buy a new mower and have had nothing but trouble from the first year.
@nodriveknowitall7022 жыл бұрын
Checklist: 1. Buy a relatively cheap riding mower 2. Search for solutions to issues with your low hours mower. 3. Go to buy a different mower. 4. Check to make sure your potential purchase doesn't have this abomination attached to it.
@michaelfanibi554310 ай бұрын
This very helpful so you don't throw away a good transmission. Thanks
@99shadows663 жыл бұрын
Is there a reliable replacement for the General Transmission RS800 CVT or should I simply put the tractor out to pasture?
@bjpowerequipment10232 жыл бұрын
tufftorque k46
@anthonyr5869 Жыл бұрын
K46 or k57
@jamrvkids14754 жыл бұрын
Is general transmission going to stand behind their product. Mine went out after starting it's second year on a Poulan 19 HP 42 inch cut mower!
@Katmandu24 жыл бұрын
What exactly "went out" on it ? Was it an Internal failure or what ?
@jamrvkids14754 жыл бұрын
@@Katmandu2 Internal failure, they stated that you could not open up to replace parts, so I had to buy a new one. Piece of trash.
@philliphall5198 Жыл бұрын
No they don’t
@jasonmcginnis49324 жыл бұрын
I have a craftmans T2200 with hydrostatic. I noticed both my rear wheel seals are leaking. I ordered parts to replace them. Also today after detaching my lawn, it started acting weird. Would not want to go in reverse, I had to force the handle backwards to get it moving. What could be the cause of this? It was really dusty and dirt job today.
@charliepearson16785 жыл бұрын
there giving it a NO LOAD test and then calling it good ...wtf ??? . when i worked for white (mtd by any other name) the test was you secured the tractor by putting the front wheels against a stationary object . then under power you engaged the trans . if the wheels spun against the ground i was good
@RusticShine4 жыл бұрын
Cant buy fucking parts for these pics transmissions
@mikegreco84512 ай бұрын
After owning one I would personally avoid buying another machine with this transmission.
@adamhubbard76284 жыл бұрын
My bypass rod is extremely hard to pull. My forward and my reverse dont work. The pedal still has a normal resistance. I'll try some of these steps but I fear the worst.
@christopherlee37924 жыл бұрын
Welcome to the club
@mb4lunch Жыл бұрын
Sweeeet! Mine has a bad belt.
@travislipscomb12176 жыл бұрын
What about losing torque going up hills?
@wwindsunrain4 жыл бұрын
I'm going to guess the belt.
@jefferybarron9293 жыл бұрын
Mine spent 2 seasons in the shop and never would climb an slope and would not reverse even on flat ground.
@garymitchell6490 Жыл бұрын
Lose of oil in transmission do to leaky seals at axle.20-50 oil
@garymitchell6490 Жыл бұрын
Lose of transmission oil 20-50 due to leaking axle seals.Noticeable by oil on inside of rear wheels.
@aaronemerick2719 Жыл бұрын
Same issue here. Passes all video checks. No evidence of oil leaks. Replaced all belts. Looks like tension is good as nothing is blocking tensioner action. Comes to full stop up hills with throttle fully depressed. Belt is spinning but can't tell if tranny pulley is spinning with it. I have a new rs800 sitting next to it ready for replacement, but not sure if that's going to fix the problem.
@yomommaahotoo2643 жыл бұрын
Anyone know why when I pull the back rod to freewheel, it doesn't? Had mine about 5 yrs now and besides replacing one axle seal, there's been no other problems.
@garymitchell6490 Жыл бұрын
Be sure break is off
@yomommaahotoo264 Жыл бұрын
@@garymitchell6490 That means i somehow have to apply the clutch whila also around back pulling that rod...even when I manage to push the clutch pedal and pull the rear rod, it still doesn't go into freewheel.
@melaniedickerson507 Жыл бұрын
What do I do if the fuel tank is above the RS800 transmission
@melaniedickerson507 Жыл бұрын
Am I going to have to remove the fuel tank so I can get to the transmission under my seat?
@terrycraig98764 ай бұрын
@@melaniedickerson507 No, just drop the trans. Full instructions on their website
@phrodendekia3 жыл бұрын
Mine does not freewheel without making crunchy grinding noises. I cant pull or push the mower without it making these noises. It has only 80 hours of use. Husqvarna YTA22V46
@phrodendekia3 жыл бұрын
@@jimhill6586 I opened it. Fully dissasembled it. Cleaned everything. I put new grease and it runs good now.
@martinberlanga49143 жыл бұрын
Did you have to remove the transmission?
@phrodendekia3 жыл бұрын
@@martinberlanga4914 Yes, I took the transmission out to fully disassemble it. I pened it like a clamshell, threw old grease out, cleaned it all, put new grease, (High Pressure grease I think it's called) and no more problem.
@martinberlanga49143 жыл бұрын
@@phrodendekia I'm confused so the transmission isn't sealed? It seems sealed and the external parts you can replace.
@phrodendekia3 жыл бұрын
@@martinberlanga4914 Nope, it's not sealed, it's glued together with some sort of poliurethane adhesive, you need to cut through it with a sharp thin blade, then very carefully pry it open. I also think there were some screws, but I just forgot the details 😅 Let me see if I can upload some pictures to a host so I can post you the links
@philliphall5198 Жыл бұрын
These are truly just junk and keeping top clean is impossible to do Which causes most of the problems
@20darleneg Жыл бұрын
So If I push the forward pedal in and try to turn the secondary pulley and it will NOT turn at all and same with reverse pedal mashed, then the pulley needs to be replaced? Pulley turns fine until I hit the forward/reverse pedal. I have lost reverse on mower and forward just barely creeps. I have heard broken control cam, rotating cam, shift cam. Are these all the same and if so you think we could just agree on one thing to call it? Also hear I need a anti debris kit, a driven kit. I think I'm ready to light the damn thing on fire. And why the he'll do I need to buy a special tool in order to replace this companies parts? Who does y'alls marketing? Just up the stupid price of that pulley kit and include the damn tool in the kit already. It's about recall time isn't it boys? You have made enough money that you can now fix some of these problems that people have spent there hard earned money on that made you rich from these junk transmisdions. This isn't China. We don't want junk!