I am somewhat handy, so I watched this video and gave it a go. Outstanding step by step guide. The generator fired up immediately and fixed the fuel issue. Highly recommend this video.

Only a good Limey could put out a video as simply explained as this one... 10 out of ten mate

I have been having trouble with keeping my Onan Microquiet 4000 running and after changing the oil and the air filter decided to give changing the fuel filter and while I was at it, pump a try. I followed this video. It was a perfect instructional video, giving tips along the way and spoke to me in practical, meaningful ways. It was a success. My generator is now purring along. Thank you.

Thank you for the great step-by-step video. You are an excellent instructor, and there are lots of little hints & tricks shown. The little humorous clips injected are a nice touch. No background music is appreciated. (western Canada)

Thank you, Jason Statham! I was able to change it out.

I am a 62 years young, ex-pat now living in Nova Scotia, Canada who took on this challenge after spending $800 + for a company to service the generator. They fixed a ground wire and explained the Gen ran perfectly using an independent fuel source. Their advice, get a gas container or use the MH as a glorified tent. 🤨 New fuel pump and filter cost less than $100 cdn, plus my time! I thank you so much for giving me the confidence to replace the old fuel pump and filter. She now works just fine, I am so proud of my achievement. Thanks again😃

Replaced my pump/filter today, your video was key in helping me get through it. Many...many thanks!

Thank you for NOT playing background music over your instructional video!!!

After watching your video I ordered everything to do a complete maintenance on the generator. Knowing ahead of time what’s involved is a great relief!! Thanks for the good information!

This is an excellent video! You brought a lot of humor and know how to a tedious process. Thanks

Great video. Changed my pump and filter out today and this video made it very simple with the step by step process you went through. Thanks for the assist!

Sitting here in my home office in Florida, watching these excellent Richie How-To's this morning. I'd already watched the video on dropping the entire generator and replacing the starter. I'll be doing that i decided, then I watched this video. I figure while I'm at it, i might as well as replace the fuel pump and filter too. I've got 600 hours on the generator and i doubt it's ever been replaced. (bought the RV recently, used). So why not? Thanks Richie. Great work.

That was really well done. I watch videos like this a lot and this may be the best I’ve seen. Never would have expected it from a Pommie. Glad you’ve escaped.

Best "how-to" I've seen. I'm the worst mechanic but i think i can do this. Thanks to your video i feel much more confident going forward.

Great video, and I’m glad I’m not the only one that gets my nuts and bolts confused when talking.

Thank you. I appreciate the detail with hooking up wires. Much appreciated.

Thank you, thank you, thank you for your detailed instructions on how to troubleshoot the Microquiet 4000 generator. It got me going without taking it to a shop.

Your videos are awesome ! I fixed my generator with your help ! You rule

That's exactly what I need to do to mine. Thanks for the lesson!

Great video. I went step farther and relocated the filter and pump. Just so be a lot easier the next time. Thank You

Super Video ! Also appreciate the British Humor! Cheers mate!

Excellent write up. I will add, at 8:40 take the plug that you removed from the fuel pump and use it as a cap on the barbed end of the fuel filter to keep debris from entering the filter before you put the fuel line back on.

Great video! Thanks mate!!

Very good.Really like your videos, easy to understand.

update: Yes, this is an awesome video that shows you step by step what to do. I tried it today and let me tell you it is definitely not as easy as it looks in this video. He just puts in his screw driver and off comes the part he targets.. Well, I spent several hours today trying to get each screw off of each piece I needed to take off. Every single nut or screw that needed to come out was a fight. Had to to go the store several times to adjust what I was using. The selenoid screw did not just come off using the half inch wrench. I had to go get a socket wrench. The they weren't long enough so had to go back to the store to get the long sockets. I also had to use penetrating oil to help loosen the screws. Finally after getting everything out except the actual fuel pump, I have one last screw that holds the pump down that I absolutely can not get loose. So I"m taking it in to an RV shop to see if someone there can at least help get that screw out. I'm hoping it's not stripped. Just know while this video makes it looks almost easy and do able for us non-mechanic types, it is anything but easy. I'm hoping tomorrow will be a better day and someone can get the screw out that holds down the fuel pump. If not, I'll have to pay the big bucks and keep my appt. at the generator shop at $210/hr. Thanks for the great video!

I rerouted/mounted the pump and filter to the outside of the genny , quick replacement now.

Really nice video! Thank you!

Awesome and very helpful! Thank you!!

Really great step by step instructions 👍👍👍 right on!

Well done! After seeing all that and thinking I would just replace the filter, I think I will replace the pump also.

Thanks for this m8. About to go out and throw my mother’s genny together finally. She’s lucky I speak limey.

Just happened across your channel from FB, great videos. Hope you keep them coming.

very good video . I have a crazy gas filter on my 2007 RV , I just got . It is on the frame , maybe for the RV but close to the Generator .

Thank you, your video helped me greatly. I was able to replace my fuel pump and filter. Thank you so much.

Thanks mate.

Thank you Richie. Great video. Thank you for doing this. It made me comfortable in doing the work myself.

Awesome video...very entertaining, too.

Nice video Sir. I just got one of these things and this is VERY valuable. Thank you.

Thanks for your video, I really appreciate your help, as I've been trying to replace the fuel filter for the past 3 hours with no success, so now I know I'm going through the front.

An excellent explanation & visual. Well done.

Great video, I loved the commentary. If you put a little grease in the hole where you put the Torx bit it will help hold the bolt to the Torx bit to make it easier to install it.

Thanks for the video! Didn’t even have to watch the whole thing and I sad I got this!

EXCEPTIONAL video 😊😊😊 No BS just straight forward how to video... Absolutely the best at explaining how to do the job.... Thanks 😊 😊😊😊

thanks man i have head the same problem generator runn for about 25min and shut off thanks to your instructions i found gas was not running after it shut off (before it shut off it ran) i could not find a fuel pump at the local rv shop went to napa autoparts they had a low pressure fuel pump replaced the fuel pump now it wotks awesome thanks again

I startedd replacing and got (FLUMMUXED) I came into the house and watched your video (You're a Life Saver) Thanks TONS!

Great video! I was going to call an RV tech out that wanted to charge me $200 without parts. did it myself in half hour with no problems after watching your video. And I'm not mechanically inclined!! Thanks again!

Your video helped me with an unexpected issue repair. The fuel pump wasn’t working so I expected it to need to be replaced however I went in thinking the possibility that the ground had come loose. As it turns out, I was wrong but on the right track. The POWER supply wire o the pump had corroded and disconnected. We use our 2020 Leprechaun to travel year round up in Alaska and through Canada and it leaves the camper exposed to lots of unexpected corrosion. Anyway, that for making the video.

Thank you for another fine video. I sure would like Onan to have made a easier way to change out the fuel pump and filter. Reminds me of how jet fighters are built and that is not for easy maintenance.

Great stuff mate. We are an Aussie couple touring USA. Just got a motor home, and I think your video is super helpful. Oh and we speak the same language…. sort of lol Spanners mate…. Love it.

Perfect step by step video, now if I just had tiny hands! On a separate note, absolutely criminal what Cummins/Onan asks for the fuel pump. I found one of the higher quality knockoffs and it works perfectly for a fraction of the Onan one.

This is how I fixed mine. In the case of: "I CAN'T START MY GENERATOR" It's has been two years since last time it was running, so I started by checking oil level full at gen (it won't start if low oil becouse of sensores), gasoline more than 1\4 tank in my RV (also safety censors), sparkplug checked for good spark, check the manual circuit braker (ON) at front RV engine compartment for current, also cleaned the carburetor and even installed new one but same situation, then checked wires and found some has been chewed by rats so I replaced them, by this time it started but stay runing only by keep pushing the switch on all the time, so I knew it was electrical problem from the engine itself, so I took the generator out from my RV to work in my garage, ( I did this by myself with some tools and old tricks) it's really heavy for one person. I disassemble the unit at my garage and started by removing the cover, then the cooling fan or flywheel unit (it's 2 items in one unit) until finally I was at the gen rotor and brushes assembly area and this is what I found: one more wire chewed by filthy rats plus the stinky rat nest in the middle of the generator motor coil, I fixed the wire and sanded the commutator copper contacts where the brushes are sitting becouse they were real duty with old urine from the rats. Then I assembled everything back together and bingo it's runing like a champion. For this project materials involved was about $60.00 including an aftermarket new carburetor and an harmonic balancer/steering wheel puller (available at any auto parts for $25.00) to pull the aluminum fan out and (flywheel). Just picture this: (Eny engine run smooth if gasoline and DC current aren't interrupted) so following this important principle you'll always find the problem to be fixed. Also if you have a onan microlite 4000 like mine, don't run it for more than a minute without the cover becouse you'll cook the engine real fast, also keep the eye on the aluminium fan and your fingers after cranking it in case you missing one or two members...just kidding. After testing the gen then put the air cooling assembly back and the rest of components including the cover and done!!! If this can help eaven one person save time and $$$ it'll make me more happy, thanks for reading!!!

This is a excellent video I can do this now thnaks to RV knowhow team thanks my brit brother

It has been easy way for you to get the control board out. My wires is so short, and it's a struggle to disconnect/connect the harness.

You make it look sorta easy? I just found out I need a new fuel filter on my Onan generator for my 2004 Minnie. I don't know though. Sounds and looks like a lot of little things to remember which my memory is not so good and I am definitely not a mechanic, so a bit hesitant to try this myself. But the local shop wants $210/hr to take a look at it and try to fix it. Ugh! I also just watched another video from someone else and yours is way better because you showed step by step what to do from start to finish. Thanks

Thanks mate!

Thanks Mate!

Hey thank you was a great video, it answered my questions why my generator won’t start, I think either not enough gas in my toy hauler I know it’s level coz it has a glass level , so I think it could also be the fuel pump Thanks bro

Jus nip it up! Love it.

Big thumbs up! I think I can do that! Ordered parts and waiting. I just hope this fixes the problem of running well then shuts off after about 20 minutes when cold start.

How to replace a fuel pump by Jason Statham LOL

Wow, that's so clean underneath! We just bought our 1998 and it's a mess

The monkey gave me a start! Lol

Excellent educational video and funny !

Great instructions. May have to leave this job for the professionals on my rig.

How all “how to” videos should be done, detailed and to the point

In house inverted blew a fuse. Have two problems solved. Thank you.

My fuel pump runs intermittently. I ordered a new pump just in case, but I suspect it's loose wiring to the pump. Has anyone seen this? Thank you for the video, it's very helpful in knowing exactly how to access the fuel pump - it's impossible to see from the service manual / diagrams online.

Where can we buy the parts? Any specific name beside fuel pump and filter? Thank you great video

I was able to remove the fuel filter from the bottom/outside. The only hard part was getting the threads to line up when installing the new one. I wasn’t replacing the fuel pump though.

You better know how to fix everything on an RV! I saw your comment that you rent them out. Question, Can you change just the filter through the hole? Can you remove the air cleaner housing and then change the pump and filter? Best wishes, Kevin

Hi! There! Thanks for great video. Mine starts and run for 3-4 minutes then shuts off. What do you think the issue is. Much appreciated!!

Thank you for the step by step explanation. I get fuel into my 4000 when I use a gal jerry can right below it but when it's connected to the Ford 450 fuel tank it is starved - no fuel getting to the carb. So I assume it's either the fuel line has a crack or the pump is too weak to pull it from the vehicle tank but not too weak to pull it from a can foot away. Does that ever happen? To test the line I used a small bulb syphon and successfully sucked fuel through it but it ran for about 1 min then it stopped and sounded like it was starved again. So I'm going with the pump replacement fix rather than a new fuel line. Am I overlooking anything? Does this make sense?

I started watching your videos to repair my friend's widow's Sunseeker 2850 so she could sell it. Found the fuel cut off switch on the bottom of the carb was bad. Saw your instructions on replacing the fuel pump and filter and decided to do that! Thank you so much! I have a concern though. The fuel line going into the filter is rock hard. It doesn’t flex. It's a 2002 unit. How do I replace the fuel line? It goes up into the floor above the generator. Help is very much appreciated!

I replaced the filter and the fuel pump on my Onan 4000 generator couple weeks ago. Fuel tank on my motorhome was below a quarter so I used a 1-gallon jug of gas at the intake to the fuel filter to check and make sure everything was running. It ran great! Today I went and filled up the gas tank on my motorhome. There is no fuel being drawn from the tank to the engine now. I checked all of the fuel line from the engine back to the gas tank. Is there a quicker way than trying to start the engine with an empty gas line in order to get gas to the generator?

Great video. I liked your step by step approach without making me sit through your whole life story. So many how to videos drag on but I did like the interjections of humorous clips. We’ll done. One question though, did you recommend replacing your filter AND PUMP every 100 hours?

Do you have a video on how to replace that fuel line from the fuel pump to the carb? Seems like it'd be a simple process.

Thanks for the video. Very helpful. Brand new RV (1 year old) and after a winter the gennie would start but would not stay on long. Figured it was a bad pump. I got the pump installed and thought I connected everything correctly but now the generator has no power. No priming, crank, zero power. I tested with a multi-meter that 12v if getting to the solenoid. Thinking maybe I have a ground issue. I took off the ground wire and sanded them down for good contact. Any idea what May be wrong and anything I can try or test next? Breaker on the generator is towards the outside. Possible that the solenoid is bad. It’s a brand new RV. Sorry for the long winded comment but looking for any help. Thanks

Thank you for the video. My generator is giving me the over crank code. How can I fix this?

Are you Jason Stathams brother? Cousin? lol You could be. HEY, go to a club and say "Don't you know who I am?" when they won't let you in. lol Like your videos and I love his movies. Well, not so much the English movies where I can only understand about half of what he says.

Should the fuel pump ever make a knocking sound? Mine does when I first hit the prime button.

Why do you need to disconnect the house battery for and oil change?

Do you need to use OEM (ONAN) replace parts? Can you use aftermarket parts?

Update #2 Well, I was able to get it all set up and installed. It does work. But now for some reason, my electrical is not working with the generator running. Any idea what is causing that?

Replaced fuel pump and two six volt house batteries on on an 7000 series. All appliances work when generator or outside power is supplied. When these two sources are removed there is no12 volt in house power. Control Panel shows no indication of power. Can you help me?

Do you have a link for the parts handy? The correct fuel pump and filter? I have the same generator.

Can put the link of where to buy the fuel pump, filter, and grease in the description?

After doing this I have no power to generator. Any suggestions ?

You change the fuel pump and or filter every 100 hours? Did I hear that right?

The wire to the fuel pump is not hot. Need help to figure it out. Please?

2:22 - Why not clamp off the fuel line then start it to let it run that fuel out?

Why do you replace the fuel pump every 100 hours?

Onan makes money selling you the same crap parts over and over again. Don't buy an Onan.