SAVE $$$- Deck and Spindle rebuild Hustler zero turn- Some can be rebuilt

Рет қаралды 18,028

Жыл бұрын

Kept throwing belts on the deck and hydro. Diagnose and rebuilt and saved a lot of money. Subscribe for more of the same type of content. Thanks for watching -Ray
Links to products on Amazon:
Pulleys: amzn.to/3Ei2gNr
Pulley: amzn.to/3WJjiey
Bearing kit: amzn.to/3UMuQfu
Spring front: amzn.to/3G2HRNN
Spring rear: amzn.to/3hyFjNf
Belt for 60” deck: amzn.to/3UNYFMK
Brake spring tool: amzn.to/3ElmjdP
Bearing / seal installer: amzn.to/3g1x5fU
This page contains affiliate links. If you purchase a product through one of them, I will receive a commission (at no cost additional to you). I only ever endorse products that I have personally used and benefitted from Personally. Thank you for your support!
If you choose to try one of the suggestions made in this video, you do so at your own risk. No information contained in this video shall create any express or implied warranty or guarantee of any kind. Any injury, damage or lose that my result from the improper use of tools, equipment or information contained in the video is the sole responsibility of the viewer and not Ray of all Trades. Please ensure that you take all proper recommended safety before attempting any project. Ray of all Trades assumes not liability for property damage or injury incurred as a result of any of the information contained in the video. #zeroturn #projectfarm #hustler If you would like to send a product for me to honestly evaluate or just things you think I could use, please mail to:
Ray of all trades
PO Box 6016
Fredericksburg , VA 22403
*Items will not be returned unless return postage is included
I appreciate each and every one of you!! Thanks for hanging out with me - Ray .
.
Please check out my friends channel at / @collectingwatches

Пікірлер: 57

@altonrowell613 Жыл бұрын

I enjoy watching someone else work. I've mechanic for 35 years.

@RayofallTrades Жыл бұрын

Thanks for watching!

@collectingwatches 10 күн бұрын

Thanks for the good video! I have a GTI that needs some help 😀

@RayofallTrades 10 күн бұрын

Lol

@kevinmaynard5070 9 ай бұрын

Thank you. You saved me $450. My mower was a lil different but the basics were the same. Thank you so much and god bless.

@RayofallTrades 9 ай бұрын

Glad I could help! Thanks for watching!!

@abw121 Жыл бұрын

Just did this repair over Memorial weekend! My only suggestion is to put the new bearings in freezer prior to installation, the cold shrinks them to the point you can use your thumb to press them in sometimes! Also you need a Spring puller to pull those springs out and install them back! I cleaned deck and applied cosmoline to underside and it drys fast and helps grass slip right off!

@RayofallTrades Жыл бұрын

Those are great suggestions! Thanks for watching!

@joeadams6333 29 күн бұрын

Very good 👍

@RayofallTrades 29 күн бұрын

Thank you very much

@CASHCRZZY1 2 ай бұрын

I replaced one set of spindles on my raptor, SD one time that old set of spindles I took to a machine shop and had them deepn the pocket so I could run a double row bearing top and bottom which makes the mower so much quieter and the bearings last a lot longer. The bearings that I put in it are 5205-2 Z double row angular shielded bearings. If you guys choose to do it, make sure you order the bearings before you take them to the machine shop so they know exactly how much to cut. you don’t need to replace your idler pulleys either if you get bearing 6203z you can heat up the flange on the idler bearing use a pair of vise grips and bend the edge back and then pull out and replace your bearings

@RayofallTrades 2 ай бұрын

Great tip! And thank you for sharing! I appreciate you.

@1cleosmom 23 күн бұрын

Ok since the factory bearings don't come with lot of grease,I took off the seals and put in the red high temp grease with hopes it will last longer . I haven't install them yet. Anyone do that here

@RayofallTrades 23 күн бұрын

@@1cleosmom⁠that’s a good idea. Thanks for sharing

@jeremyrichard7277 11 ай бұрын

Great job 👏

@RayofallTrades 11 ай бұрын

Thank you for watching!

@altonrowell613 Жыл бұрын

Nice job. I like your work.

@RayofallTrades Жыл бұрын

Thank you for watching and commenting!

@kevinlawhon1697 Жыл бұрын

Great help!

@RayofallTrades Жыл бұрын

Fantastic thank you!

@donseals9145 Ай бұрын

You did a great job and good explanation!

@RayofallTrades Ай бұрын

Glad you enjoyed it and thanks for the feedback!

@andretraversy9391 Ай бұрын

Tank's Nice video,

@RayofallTrades Ай бұрын

Thanks for watching

@davidfarm8095 2 ай бұрын

thank you I have same hustler

@RayofallTrades 2 ай бұрын

You are very welcome. Thanks for watching!

@sherrischneider2794 Жыл бұрын

The wire to the starter is not hot until the solenoid is engaged. The starter is the new part that replaces the bad starter. There on the third model for replacement.

@RayofallTrades Жыл бұрын

That is correct. This type of starter uses an external solenoid that is hot on ignition start. Thanks for watching

@Iz0pen 9 ай бұрын

If I have to arc the solenoid does that suggest I need a new ignition switch? My 54” is in bad shape 😭

@JefferyAshmore 28 күн бұрын

@@Iz0pen no bad solenoid.

@nuffdoggiggey4103 Ай бұрын

I ran across your post, i have the same mower and am in need of the same service. Thanks for the post. It helps me determine what parts i need and dont need. It seems my deck is a bit noisy when engaging the blades. The spring, i think, must be the issue. The starter drags a bit, but I'm not sure if I'll change that out yet. Oh, my middle blade is completely bent 90 degrees down. i don't know how it's working like that.

@RayofallTrades Ай бұрын

Thank you and good luck! Some people paint the underside of the deck when it’s apart to make it last longer too

@travisricks3436 Жыл бұрын

Nice work on the Hustler!

@RayofallTrades Жыл бұрын

Thank you so much for watching!

@travisricks3436 Жыл бұрын

@@RayofallTrades you’re welcome. I just bought a new Hustler Fastrak SDX 60 on 01-10-2023. I been watching Hustler mower videos. I might drill and tap for a grease fitting on the spindles when it comes time to rebuild them.

@RayofallTrades Жыл бұрын

@@travisricks3436 if the bearings are sealed like mine, it won't help. Worth a look though. Thanks!

@travisricks3436 Жыл бұрын

@@RayofallTrades yes the bearings are sealed, but you have to pop the seal off. Very easy to do.

@charlespropes1340 Жыл бұрын

I am putting new pulleys on mine. Do you know if a Torque setting is needed to put the pulleys back on?

@kevincandelario2158 9 ай бұрын

Love

@RayofallTrades 9 ай бұрын

Thanks for watching!

@joshsundiwa 11 ай бұрын

Thanks for sharing👍 at what speed are these blades running at?

@RayofallTrades 11 ай бұрын

Sorry but I've never put a tachometer on the blades. Thanks for watching!

@JoshuaDavidson-qb6sf 8 ай бұрын

I've got the same mower and just replaced all 3 spindles, tensioner idler pulley, both springs, and both belts. It's a totally different mower. I got the spindles off Amazon for $60 and they're made very well. Thanks for the video.

@RayofallTrades 8 ай бұрын

Very nice! Thanks for sharing and watching!