Semi-Auto Power Shrinker/Stretcher?!
Рет қаралды 54,647
Күн бұрынHere's a must-have video that will guide you through building a pneumatic stand for your manual shrinker stretcher set. The pneumatic cylinder takes the effort out of using a shrinker stretcher and the pressure regulator ensures that every bite of the shrinker and stretcher is consistent for even gradual bends. The overall size of this unit takes up an even smaller footprint than a manual hand-operated unit and a MUCH smaller footprint than a foot-operated machine.
Be sure to stay to the end of the video for a blueprint for the build so you can build your own.
0:00 Intro
1:11 Why Pneumatic?
3:10 My Amazon Shopping Spree
3:47 Two Types of Pneumatic Pedal Valves
5:52 The Design Process
7:59 Cutting Out Parts
14:30 Assembly Time
17:14 First Test
17:53 What Does a Shrinker/Stretcher Do?
19:20 Blueprints!
Here are the parts that can be ordered from Amazon.com. Only a couple will need to be purchased elsewhere.
As an Amazon Associate, I earn from qualifying purchases.
Parker Air Cylinder 2” Diameter 6” Stroke
amzn.to/3uW978b
Air Pressure Regulator
amzn.to/3yerx6e
5 Way Foot Pedal Valve
amzn.to/3hveS9a
Air Line and Fittings
amzn.to/3hvqJE8
1/2” 20 Clevis
amzn.to/3huuo4Z
3/8” Quick Release Pin (Bottom)
amzn.to/3hrcyQp
1/2” Quick Release Pin (Top)
amzn.to/3uU8g7U
1/2” Bronze Bushings
amzn.to/3hrZ8U7
NOT currently available on Amazon
1" DOM tubing with 1/8" wall. For handles.
1/2-20 Stainless Jam Nut
The Tools Featured in This Video:
As an Amazon Associate, I earn from qualifying purchases.
Empire Abrasives
lddy.no/vxuk
Get 10% Off! Use Promo Code GarageFab
Harbor Freight Grinder
Corded 4-1/2 in. 5 Amp Angle Grinder
Welder ESAB Fabricator
amzn.to/3hI8Thp
Plasma Cutter Hypertherm
amzn.to/3uShQbw
Vise Wilton
amzn.to/3tRNSDc
Hole Cutters - Hougen
amzn.to/3tMnbQp
amzn.to/3hudtPX
Sheet Metal Shears - Kett
amzn.to/3uW0VEQ
The Video Production Equipment I Use:
Cameras:
Sony A7iii Mirrorless Camera
amzn.to/3uTZlUb
Lumix G7 Mirrorless Camera
amzn.to/3wbihOw
Audio Equipment:
Rode Wireless Go Lav
amzn.to/3bvamDv
Giant Squid Lav
amzn.to/3wbiEso
Sound Recorder Zoom H4n Pro
amzn.to/3wg8s1P
Tripod Manfrotto
amzn.to/3tRdQqr
Tripod Head
amzn.to/3fhRpW6
Neewer Camera Slider
amzn.to/3floyjR
Teleprompter
amzn.to/2STdMK2
Lighting:
Flashpoint Ring Light
amzn.to/3wb6jUV
Phottix Nuada R3
amzn.to/3w7GANa
@dennistwitchell8821 Жыл бұрын
Just built mine and had to use a Tailon sc50-100 cylinder as the one you used seems to no longer be available. Mine uses a 4 inch stroke, which seems.more than enough. Requires a cooresponding pivot that screws onto the base and the yoke is bigger than the one in the video.
@GarageFab Жыл бұрын
Thank you for that, Dennis! I noticed the one I used vanished. Very frustrating. I’ll pin your comment. It might help someone! I’d love to see yours!
@jayinmi3706 2 жыл бұрын
I've seen a couple of videos of people making their own foot pedal operated stands, but never a pneumatic one. This is awesome.
@GarageFab 2 жыл бұрын
That’s cool to hear. I didn’t bother checking if it was original or not. Thank you Jay. Cheers!
@CraigHollabaugh 6 ай бұрын
I know nothing about pneumatic cylinder force until today. I finally, after years, looked it up. Wow, I need to start using these. Thanks, I'll be making something similar soon for my shrinker/stretcher.
@GarageFab 6 ай бұрын
Nice! Lemme know how it goes, Craig!
@CraigHollabaugh 6 ай бұрын
@@GarageFab will do, got the HF shrinker/stretcher today (20% off). Bent my first piece of 18ga this afternoon. This is going to solve some fab challenges.
@dennyo3992 Жыл бұрын
I gotta get me some of those rotacutters! Man, the tip on the guide for the rotacutter, then the carbide burr in the router....genius!
@GarageFab Жыл бұрын
Highly recommended, Denny. They’re called Hougen RotaCut Hole Cutters. They’re kinda pricey but worth every penny. Here’s a pair of associate links to the two specific sets I own… Small amzn.to/3guFEwJ Large amzn.to/3ukxxL5 Thank you, my friend!!
@ralphchristopherson782 29 күн бұрын
Really Really appreciate your ideas and sharing them with us! I’ll be in my garage now avoiding the honey due list 😅
@GarageFab 29 күн бұрын
Haha! Don’t tell her I’m the reason. I don’t need anymore haters. 😬 Best of luck my friend.
@UnconventionalMetal 2 жыл бұрын
I just watched this again. I forgot about the offset hole drill trick👍, and excellent job on the truck in your intro. Good to see a TPI intake still being used today.
@GarageFab 2 жыл бұрын
Thank you, Brother! I’ve got a confession to make. A couple actually. One: The truck in the intro is only a digital rendering of my next project. It’ll be a complete rebuild of a truck I built years ago that was destroyed in a hit and run. You can see what it once looked like, TPI and all, in the first serious KZfaq video I made. kzfaq.info/get/bejne/a7-gg6l0s7POeWg.html Two: I recently changed plans and the TPI won’t be coming back. I’m excited to reveal the new plans soon. The TPI might be going into an old 30s Chevy truck if I can get my old boss to sell it to me. We’ll see how that one goes.
@CALDues 4 ай бұрын
If you could have patented the bonus tips in this video, you'd never need a sponsor. Another great video. Thanks!
@GarageFab 4 ай бұрын
That would be a dream! Unfortunately, I think this has already been done. Shortly after building it, I started searching for a pneumatic stand. It was a long time ago but I vaguely remember finding one. Honestly I’ve never searched for a patent, I just assumed there was one already.
@immanutt4442 Жыл бұрын
Yes !!! ... the skeletonized uprights are def worth the time
@GarageFab Жыл бұрын
I agree!
@derJackistweg Жыл бұрын
Fun to watch - and no ads = great. When you stopped and said "this video was ... " I already had my finger already on the arrow right key....
@GarageFab Жыл бұрын
Haha! Thank you my friend.
@thestreets5206 Жыл бұрын
What a time to be alive.... this is a game changer. I'm going to copy this NOW ☝👍👍👍
@GarageFab Жыл бұрын
Yes! Please do. I’d love to see it if you’ve got an Instagram. @GarageFab Best of luck! Cheers
@gixrman Жыл бұрын
I needed this several yrs ago. I had a product that I was selling that required a radius on aluminum angel, I spent hours in my shop on the shrinker for each one. It got to the point that I truly hated it and stopped making it. Good job on this and the design.
@GarageFab Жыл бұрын
Yuck. I can picture it. 😩
@roberthowland4503 2 жыл бұрын
That was a great idea and will help a lot of fans thanks I really enjoyed watching
@GarageFab 2 жыл бұрын
Much appreciated, Robert! It’s definitely one of my favorite tools right now. Thank you! 🙏
@sincitysanta 3 жыл бұрын
Oh man, thanks for putting together this inspiring video. My shrinker/stretcher set has been in the box way too long.
@GarageFab 3 жыл бұрын
Haha!! Mine literally sat behind our couch for two years. Right where I put it after opening it for Christmas. Good luck, Brother! And thank you. 🙏
@smokeyray5017 2 жыл бұрын
OK Mr. Wizzard, pretty clever! I just bought a set of these and will be using your idea. You know I don't believe a lot of folks understand how much work and engineering it takes to build something like this. If you had to buy, it would be pricey. Thanks for the info. Keep up the good work!
@GarageFab 2 жыл бұрын
Very much appreciated, Ray! I wish I was savvy enough to cobble together an online store. I’d consider selling a kit for those that don’t want to tackle it for themselves. Good luck my friend! Lemme know how it works! 🍻
@steveveness3829 2 жыл бұрын
G'day from West Australia, 😉 One word fellow internal combustion engine propelled vehicle enthusiast . " Nice"🙂👍👍
@GarageFab 2 жыл бұрын
Haha!! Thank you, Steve. Very cool to hear these videos are making it that far. Cheers mate! 🙌
@jodydewey3516 2 жыл бұрын
using a router for sculpting like that - GENIUS!!!! It never even crossed my mind...and I have 3 of them....
@GarageFab 2 жыл бұрын
Thank you Jody! Lemme know how it works! It’s been a lifesaver for me so far. The table of the router keeps the edge of the cut straight up and down giving a machined appearance. 🙌
@henryverrydt4943 7 ай бұрын
Awesome, just found you and this is a great idea. Definitely following. My take on a tool stand is 1 post mounted to the floor, and removable tools mounted on the wall brackets.
@GarageFab 7 ай бұрын
You’re going to love the next video, Henry! 😆 Just wrapped up filming this evening. Thank you my friend. Happy to have you.
@stevehaulsforyou1286 Жыл бұрын
Dude amazing content. Can't wait till I'm doing this stuff also
@GarageFab Жыл бұрын
Thank you, Steve!
@andyb7754 Жыл бұрын
Loved the video!! I subscribed a couple weeks ago and I'm looking through your old videos. Thanks for your videos. Makes me want to build one of these shrinker/stretcher stands after I get to my summer home. Thank you again.
@GarageFab Жыл бұрын
My pleasure, Andy! Best of luck with the build!. You know where to find me if you’ve got questions. Cheers!
@aaronb554 2 жыл бұрын
Dude THANK YOU SO MUCH for this how-to! I'm out here pumping away on some 18 gauge flanges and I'm super thankful for the information and the parts list.
@GarageFab 2 жыл бұрын
My pleasure fellow Aaron! It’s been a lot more handy than I ever expected. Good luck my man!
@JoJo-js5ft 2 жыл бұрын
Make your money. Put the ads we'll still be here!
@GarageFab 2 жыл бұрын
That means a lot, Jo Jo! I appreciate you. 🙏
@waiting4aliens 2 жыл бұрын
Thank you very much for all the effort and thought you put into this video. Have a good holiday.
@GarageFab 2 жыл бұрын
You as well!! Be safe and thank you for the kind words. Cheers!
@pet1srg 2 жыл бұрын
Man I was thinking of a stand, your idea is awesome 👍👍👍 thanks man
@GarageFab 2 жыл бұрын
My pleasure, Scott! Best of luck!
@ogt92fromthe1step9 Жыл бұрын
So I just wanted to let you know I took this idea and ran with it. I have two separate air cylinders controlled by electric air solenoids into separate pedals. I'm extremely pleased with the results. And with the adjustable PSI in the way I built mine I have adjustable heim joints much like a tie rod. I built it in such a manner because the cylinders I had already were limited travel about 7in to be exact. So you could either screw-in or screw out the tie rod the adjust for thicker metal and I'm extremely pleased with the results. 👌 Thanks again for the inspiration. 🤟
@GarageFab Жыл бұрын
Yes! Do you have Instagram or another way of sending over some photos/video? I’d love to see what sounds like an incredible project. Very well done, my friend. 👏
@ogt92fromthe1step9 Жыл бұрын
@@GarageFab not really up on the gram to often but I'll see what I could do because like I said you gave me the inspiration for it and I really think you would appreciate it. I'll comment back here when I put it up. Mind you it's not as clean as yours but it does the job extremely well. It does have some bead rolled panels at the top of the table just for an extra touch lol but I really think some speed holes would really class it up a bit haha. What's your Instagram?
@GarageFab Жыл бұрын
@@ogt92fromthe1step9 Operation is all that matters! That and the pride of building it yourself. Haha! “Speed Holes” My Instagram is @GarageFab believe it or not. Cheers!
@ogt92fromthe1step9 Жыл бұрын
@@GarageFab noice I'll hit you up soon
@ogt92fromthe1step9 Жыл бұрын
@@GarageFab if you get a chance ya have to check out the 25ton press brake I've been helping setting up for my uncle. She's a big girl lol 8' tall 6' wide in about 4 ft deep when the package tray is installed. It's on my Instagram just getting it's standing up. I still have to build him another rotary phase converter to power it but I have a couple good ideas for some real nice beaded and louvered panels using this machine. Just thought you'd get a kick out of that.
@lloydrmc Жыл бұрын
Pneumatic is PERFECT! The cylinder will "give" before gouging the work piece. Plus it's probably faster than hydraulic.
@GarageFab Жыл бұрын
So far so good my man! I couldn’t be happier. I’ve had a few folks say that you wouldn’t be able to ‘feel’ the workpiece and make fine adjustments on the fly. I don’t know what they’re feeling. Maybe I’m numb, but I can’t feel the metal moving with a manual shrinker/stretcher. The consistent pressure with every application of the pneumatic system has made it incredibly easy to make perfect uniform curves!
@heidielliott3881 3 жыл бұрын
I am behind but I love how much you enjoy what you do! As always make me want to go out in the shop. Glad you are finally using the tools the wifey gets ya too!
@GarageFab 3 жыл бұрын
Hahaha! Me too! I think she was getting sad they were still sitting behind the couch.
@Deesrickchevrolet 3 жыл бұрын
Aaron, I've been a fabricator all my life my friend. From the Portland shipyard plate shop, building pre fab bridges and pre fab nuclear modules, my truck was my tinker toy. If I had any part of influencing you. I am truly flattered, but you have a gift my friend. This idea is totally thinking outside the box and I think it awesome, It's what fabricating is all about. Great stuff and you had me LMBO many times. You're inspiring me.
@GarageFab 3 жыл бұрын
Is there a blush emoji? 😳 Thank you, Brother. Glad to have you aboard. I think this is going to be an exciting ride.
@ItsAdam12 11 ай бұрын
You ManKandy genius! I never thought to use a hole saw guide to enlarge a hole!
@GarageFab 11 ай бұрын
Thank you Adam! If you haven’t seen it already, this video goes into greater detail and has a couple other tips. Hole Saw Tricks That Might Save the Day! kzfaq.info/get/bejne/rddhaZyor8mZaac.html
@michaelanderson3771 2 жыл бұрын
So glad I saw this and particularly the reuse of the router - such an awesome tool for fine control of the carbide bit on plate stock
@GarageFab 2 жыл бұрын
Thank you Michael! The carbide router has definitely improved the look of a lot of my projects.
@kurtludwig6962 7 ай бұрын
Fantastic tool idea
@GarageFab 7 ай бұрын
Thank you, Kurt! 🙏
@rodritz8384 Жыл бұрын
Don't have a shrinker stretcher but I did watch this all the way because I just like watching people build stuff. One question, couldn't you have made a small extension for the bottom to turn the cylinder 90 deg.? would have moved the pivot pin location down 1/2 to 3/4 inch.
@GarageFab Жыл бұрын
Yeah, definitely would’ve been an option. That never crossed my mind, and it probably would’ve been a lot faster than cutting the arched hole! 🤷♂️
@jakeevans56 3 жыл бұрын
Really really enjoy all your videos, can't wait for more to come out. Keep up the good work 😊
@GarageFab 3 жыл бұрын
Thank you, Jake. I can't wait to make more. 🍻
@kellyjones334 3 жыл бұрын
You should have a smile on your face when you first tried that. Great job and video.
@GarageFab 2 жыл бұрын
I'm still smiling!! Thank you, Kelly. Cheers!
@edparker1972 Жыл бұрын
The router tip is genuis!! Thank you
@GarageFab Жыл бұрын
Thank you, Ed! Sometimes it’s the little things.
@MH-rb7lp 2 жыл бұрын
Awesome build, I am going to do this to my shrinker/stretcher set.
@GarageFab 2 жыл бұрын
Sweet!! Lemme know how you like it! 🍻
@danreagoso3939 2 жыл бұрын
Very generous to put this on you tube Thanks!
@GarageFab 2 жыл бұрын
My pleasure, Dan! Hope you get some good use out of it.
@dirtywaterfab1695 Жыл бұрын
hey man, just found your channel today and i've spent hours watching. great stuff! i've learned quite a bit today, and i look forward to more great content. thanks!
@GarageFab Жыл бұрын
Thank you my friend!! You’re very much appreciated. 🙏
@joehobo00 8 ай бұрын
That totally looks legit, nice work! Also, thanks for the hole-saw tip, I'm sure I'll end up using that. Plenty of times I've had to make a hole larger, and I found that Bosch makes a handy bit that you can chuck 2 hole-saws onto.
@GarageFab 8 ай бұрын
Brilliant! I’ve had a few folks tell me I could use a hole saw to center a hole saw but I couldn’t figure out how to do it. Now I know! Thank you my friend. 🙏
@joehobo00 8 ай бұрын
BOSCH HE1 2-Piece Hole Enlarger Kit @@GarageFab
@jonelwood880 2 жыл бұрын
So I had my doubts at first. Mainly because the Air Cylinder is weakest on the retraction stroke due to the annular area of the piston and rod. Anyway it looks like it works. I too have had the same tool sitting on the shelf, I also have all the parts I need already so I will build one Great job. Looks good.
@GarageFab 2 жыл бұрын
Thank you, Jon! You are correct. The shaft takes up a lot of the volume making it a little less effective. So far I’ve been able to do anything I’ve needed to work under 80psi. I suppose you could build the whole thing upside-down to squeak a little extra power out of it! Good luck my friend!
@jimmyh7718 2 жыл бұрын
Just simply awesome! Thank you for sharing your ideas. You are keeping it real. Keep it up.
@GarageFab 2 жыл бұрын
Thank you, Jimmy! Imma keep going until I can’t go anymore! 🙌
@cotybrown1226 3 жыл бұрын
Great video. Congrats on the KZfaq milestone. Looking forward to what the future brings.
@GarageFab 3 жыл бұрын
Me toooo! Thank you! I'm going to start up the KZfaq community message board soon where I can ask subscribers which project should be next. Thank you!
@EnsVibes 3 жыл бұрын
One of the best fab channels I've seen, keep the great work
@GarageFab 3 жыл бұрын
Thank you Luis! That means a lot. 🍻
@markrs2000 2 жыл бұрын
Just found your channel. brilliant absolutely brilliant. You explain stuff clearly, but also keep it interesting. Please keep going. I hope you make loads of money, good luck.
@GarageFab 2 жыл бұрын
So far I’m averaging $150 a month. So I guess you can say I’ve already hit the big time. 😉 I kid. I’m blessed to making even that much. Some people have none. Thank you for the kind words, Mark. You are appreciated. 🍻
@jeffmesser796 2 жыл бұрын
You are correct on both accounts I’m slow and old. But the brain of 5 yr old. Enjoying your projects!!
@GarageFab 2 жыл бұрын
Haha! Thank you my man!
@keyblazerslittlegarage3563 Жыл бұрын
Awesome Build, and exactly what I needed for my stand! I will be doing this build at some point in the future, and will credit you in my thread over on Garage Journal! Thanks, you ROCK!
@GarageFab Жыл бұрын
I’ll never argue with someone who wants to share Garage Fab with someone they think would benefit, but you don’t owe me any credit. Thank you my friend! I’d love to see it when you done!
@kustomacegarage5320 3 жыл бұрын
Thank you for no adds..... I will be making this!!!
@GarageFab 3 жыл бұрын
My pleasure. Good luck.
@whizwhisnant 3 жыл бұрын
Another outstanding video Aaron!!!
@GarageFab 3 жыл бұрын
Thanks man! I think I need to put out the worst video ever and see what you have to say about it. 😄
@tiammax Жыл бұрын
Nice job and Super convenient
@GarageFab Жыл бұрын
Thank you my friend! 🙏
@charlesstatkus 2 жыл бұрын
I show my appreciation by Subscribing to your channel. All I can say is WOW! Just getting into metal fab. Powder coating would be the extreme in perfection. Got my Shrinker/Stretcher with stand today (Amazon Sunday FedEx). Ordering the suggested parts for air assist! Thank you!
@GarageFab 2 жыл бұрын
Thank you Charles! It’s too soon to make any promises but I purchased a steel office cabinet a year ago with the intent to create a powder coat oven. It’s definitely happening but unsure when. I can’t wait to see the shrinker/stretcher! Cheers my friend! 🍻
@frediefarmer 2 жыл бұрын
Awesome build. Works great .👍🏽🇺🇸👍🏽
@GarageFab 2 жыл бұрын
Thank you, Fredie! 🍻
@lonnies3960 7 ай бұрын
Nice! I do have the Harbor Freight shrinker/stretcher on a foot operated stand that I bought used. Even with the foot pedal, it's awkward to operate. You pneumatic rig looks like the way to go. Cheers.
@GarageFab 7 ай бұрын
I’m super happy with it so far. The big problem for others seems to be the pneumatic cylinder I used isn’t available any more. You might have to locate an equivalent.
@Ghost-um2jw 3 жыл бұрын
Great content as always. Thanks!
@GarageFab 3 жыл бұрын
Thank you, my friend. 🙏
@OmarRamirez-xz7eo Жыл бұрын
I’m pressed with the quality of channel and videos . Cheers
@GarageFab Жыл бұрын
Thank you, Omar!
@murillofabworks 8 ай бұрын
This is actually a fantastic idea! Great job dude!
@chrisbenn8691 2 жыл бұрын
That's a brilliant set up. I have to swap my units on the bench and every time tell myself I've gotta stop doing this!. This is definitely something that I could put together. How about a follow up for a deep throat (sounds ominous) unit?
@GarageFab 2 жыл бұрын
Thank you, Chris! I’d love to have a deep throat stretcher though I honestly don’t know what I’d use it on. I just like to own cool tools! So it likely won’t be anytime soon, but I can definitely see a follow up coming in the future.
@brianskor364 Жыл бұрын
just came across this channel and its rad. Love the work you do and how well you explain everything. keep killing it and looking forward to going through all the videos. 👍
@GarageFab Жыл бұрын
Thank you, Brian! Glad you found me. Hope you enjoy the rest! See you in the next. 👊
@uppers7703 3 жыл бұрын
Top notch as always brother 🤙🏾🤙🏾🤙🏾
@GarageFab 3 жыл бұрын
Thank you, Sir. 🙏
@suraaaji 2 жыл бұрын
This is what I'm looming for!
@GarageFab 2 жыл бұрын
Excellent! I hope it helps you as much as it’s helped me. 🙏
@aurktman1106 Жыл бұрын
Well, now I have to build this for my shrinker/stretcher set. Gee... thanks... :-)
@GarageFab Жыл бұрын
Yes!! I’m honored to have contributed to your To Do list. I can’t wait to see it! And also sorry. 😞
@jameslangford4748 Жыл бұрын
Always great tips. Thank you !
@GarageFab Жыл бұрын
My pleasure, James! You gonna make one?!
@chrispool6742 9 ай бұрын
Brilliant idea
@GarageFab 9 ай бұрын
Thank you, Chris! 🙏
@johngarloff 2 жыл бұрын
Well done! Thanks for the tutorial.
@GarageFab 2 жыл бұрын
My pleasure, John! Thank you! 🙏
@frankm8533 2 жыл бұрын
Always impressed with ur skills ive binged watch all ur vids in 3 days I think. You make it look easy take it from a old minitrucker who drank more beer then he did learn metal fab the right way. Ur skill is top notch to me brotha
@GarageFab 2 жыл бұрын
Haha! Thank you bruh. I owe you my KZfaq paycheck this month. (If I get one) That was my reason for leaving the truck club. When I joined it was trucks and alcohol. Then it transformed into Alcohol and trucks. And at some point… Alcohol. 🤦🏻♂️ Thank you Frank. You truly are appreciated.
@frankm8533 2 жыл бұрын
@@GarageFab 2 buddies & I started a club late 90s till later 2000s beer was cool at first but I was traveling far to other shows with other big clubs I'd be the only one from my club and none of them would ever go they would say they couldn't afford it but they had plenty of money for weed and beer. After years of that we all broke up. I still see them all but I'm the only one that's still into the scene.
@GarageFab 2 жыл бұрын
Word. It’s for the better. I made a few really good friends in the club that I still see and when we get together we talk about… trucks. It’s a win. Not to mention I met my soul mate while at a club party. No complaints. I still occasionally ponder creating another club that revolves around all the awesome that I once experienced. Like going to a buddies garage to hang, drink a beer and help get his truck ready for the next show. Maybe this channel will bring like minded folks together. 🤔
@frankm8533 2 жыл бұрын
@@GarageFab hmm that sounds like a good idea 💡
@RobertsVintageGardenTractors 2 жыл бұрын
I have that same set of mac carbide de-burring bits and I really like them.
@GarageFab 2 жыл бұрын
I’m very pleased… With the tools. My Mac guy vanished so I can warranty one of my broken bits! 😩
@RobertsVintageGardenTractors 2 жыл бұрын
@@GarageFab, The mac guy usually only stops at the shop I work at every once and a while. I got some drill bits from him too and they’ve been pretty good so far. I wonder if you could warranty the bit online on their website.
@GarageFab 2 жыл бұрын
It’s worth a shot!
@TomofAllTrades 11 ай бұрын
Great video with really good info and production quality too 👍
@GarageFab 11 ай бұрын
Glad you enjoyed it! Thank you, Tom!
@shannonortega4677 Жыл бұрын
I would love to see the layout of your shop. I also build cars and motorcycles from my home. Shop space just cost to much right now. I'm always looking for new space saving ideas. BTW no idea why this is under my wife's name. Lol. Tim, Liquid Cycle Designs
@GarageFab Жыл бұрын
I feel you! I’d love to expand as well. One day! I imagine we’re getting close to needing to do a shop tour. There’s some things I need to organize and I want to include that in a video, but I suppose I should include what it looks like this very moment since that’s what it has looked like since the beginning. Shrug. Maybe I’ll do a before and after video. 🤔 Maybe at 50k?
@beatlebug9622 Жыл бұрын
A hi and a wonderful new year for all from Greece! Keep doing what you do! I like your work.......
@GarageFab Жыл бұрын
Happy new year to you back! Always appreciated my friend. 🙏
@derekpaton2775 2 жыл бұрын
great info, well presented. thank you
@GarageFab 2 жыл бұрын
Thank you, Derek! You are appreciated.
@Verticalpedalgarage 2 жыл бұрын
Bro this is genius!!! I’m loving the router idea to!!!!
@GarageFab 2 жыл бұрын
Thank you Sir! 🙏
@BrennanHoyt Жыл бұрын
I thought you where going to use a "Watts-Link" design to pull both shrinker and stretcher arms at the same time. That'd be cool and highly over complicated lol. Of course you'd have to clock/offset the two tools slightly to allow the two pull down arms to pass each other or add more separation front to back. The Watts-Link center would be connected to the cylinder shaft and a link that would go each tool. The Watts-Link's "parallel" links would hold the "propeller" and cylinder shaft from favoring and swinging toward the tool currently under load. A side benefit is the air line slots wouldn't be needed either. In the end, life is short and time is precious, so your way is better. It would be cool though.
@GarageFab Жыл бұрын
It absolutely would be cool! And unnecessarily complicated is my signature! If it’s not complex it’s not interesting. Who cares about practicality!
@tw3378 2 жыл бұрын
Another cool build.
@GarageFab 2 жыл бұрын
Mucho thank you!
@jaisonbadillo5139 3 жыл бұрын
Great work!
@GarageFab 3 жыл бұрын
Thank you, Jaison! 🙌🍻
@FrEHV 3 жыл бұрын
Came here for the perfect Miter Cuts video. Stayed and subscribed because of the other great content and the concept of this channel. Greetings from Holland!
@GarageFab 3 жыл бұрын
Hartelijk bedankt. Glad to have you. 🍻
@keithlanning7381 Жыл бұрын
You are doing awesome job.i hope you get another way to fund you but as good as your videos are i think you are worth a add or 2 thank you for sharing your gifts
@GarageFab Жыл бұрын
Thank you, my friend!
@cn8484 2 жыл бұрын
Awesome idea I'm going to build 1 for my shrinker stretcher keep up the good videos
@GarageFab 2 жыл бұрын
Nice! I’d love to see it when you’re done. Good luck and thank you! 🍻
@cn8484 2 жыл бұрын
@@GarageFab will deff send over pictures thanks again dude 👍
@Johntasticful Жыл бұрын
Sweet! So much great jnfo and fab’n.
@GarageFab Жыл бұрын
Happy to be of service John! Thank you 🙏
@petascalecomputing Жыл бұрын
Thank You!
@GarageFab Жыл бұрын
Thank you for watching, my friend! 🍻
@kjm4ryanna 3 жыл бұрын
Your videos are so awesome it just makes me want to get off my butt and go out and do stuff
@GarageFab 3 жыл бұрын
Yes! Do it! Stop watching dumb videos and go weld something!
@dannysteele4013 Жыл бұрын
Great idea thanks for sharing..
@GarageFab Жыл бұрын
My pleasure, Danny. Thank you for watching!
@kurtludwig4783 2 жыл бұрын
Awesome links for all cool stuff you use
@GarageFab 2 жыл бұрын
Appreciated! Hope they help.
@DinasGarage 3 жыл бұрын
Awesome video Arron! Yes I would be interested in the metal set! Man your videos are so cool! Congratulations on the milestone! #keepminitruckinalive
@GarageFab 3 жыл бұрын
Thank you, Brother! I'm working on my website and setting up a store. I'll let you know if I ever get it up and running.
@horaciotello8017 2 жыл бұрын
I need to build this tool👏🏻👏🏻👏🏻👏🏻
@GarageFab 2 жыл бұрын
You do! Let me know how it goes. 👊
@deborahnblaineaucoin 3 жыл бұрын
Way too go. I love it. I have the same ones and wanted to build something just like yours. ThanKs
@GarageFab 3 жыл бұрын
Yes! My pleasure and good luck!
@seanalexander9531 2 жыл бұрын
I've just found your channel. Very slick! I'm definitely looking forward to more videos :)
@GarageFab 2 жыл бұрын
Thank you, Sean! More in the works and enough projects planned to last for years. Glad to have you!
@josephkandrot1045 2 жыл бұрын
Love it!
@GarageFab 2 жыл бұрын
Thank you, Joseph! 🙏
@Johntasticful 3 жыл бұрын
Great video! Thanks
@GarageFab 3 жыл бұрын
Thank YOU! 🍻
@woowocgwhwrehvcb Жыл бұрын
Cool project.
@GarageFab Жыл бұрын
Thank you Scott. You gonna make one?! 🙌
@cannednolan8194 Жыл бұрын
Found your channel a couple of days ago. Got my sub. I’m going to have to build something similar. But I have a small English wheel, small pneumatic hammer, and some princess auto shrinker and stretcher that also need the cases made. I’m going to want them all on the same stand. Later want to build a bead roller for it. Use the pneumatic to spin the roller. Ive got big dreams. Lol
@GarageFab Жыл бұрын
That sounds amazing! I hope to see updates as this little fab island develops. Happy to have you my man.
@UnconventionalMetal 2 жыл бұрын
Thanks for awesome router tip!
@GarageFab 2 жыл бұрын
My pleasure! 🙌
@indyz12 Жыл бұрын
You sir, have a new subscriber
@GarageFab Жыл бұрын
Thank you, my friend! 🙏 Glad to have you. I’ll see you in the next one!
@made_by_chris 2 жыл бұрын
Great video man.
@GarageFab 2 жыл бұрын
Thank you Chris! Gonna build one? 🙌
@123suzukisamurai Жыл бұрын
Excellent. Love yr channel. Just discovered it
@GarageFab Жыл бұрын
Thank you! Glad you found us. Happy to have you!
@DieselRamcharger 2 жыл бұрын
you can get spring extend or spring retract cylinders as well. the spring is internal. only need air to move it in one direction..... :)
@GarageFab 2 жыл бұрын
Interesting. I’d like to see one of those. Do they work quickly?
@markmcintosh3255 2 ай бұрын
Brilliant!!
@LoenInk Жыл бұрын
Fantastico!!
@GarageFab Жыл бұрын
Thank you my friend! 🙏
@patrickmoreng387 Жыл бұрын
Thank you bro
@GarageFab Жыл бұрын
My pleasure, Patrick. Thank you for watching!
@kevstylemedia5115 3 жыл бұрын
Good stuff keep it up
@GarageFab 3 жыл бұрын
Thank you! 🍻
@michaelwdavis 3 жыл бұрын
Superb!
@GarageFab 3 жыл бұрын
Thank you, Michael! 🍻
@rdspeedfab 3 жыл бұрын
Just found your channel. Really enjoying it. Subbed 🍻
@GarageFab 3 жыл бұрын
Thank you, Rob. Glad to have you! 🙌
@toddenglert4815 2 жыл бұрын
First video for me but I dig video and will be watching for upcoming videos good content
@GarageFab 2 жыл бұрын
Thank you, Todd! There will be so much more! Have a great week! 🍻
Dharni
Рет қаралды 151 МЛН
Metal Shaper Tom
Рет қаралды 134 М.
Garage Fab
Рет қаралды 164 М.
agro_fermer116
Рет қаралды 1,8 МЛН
Wrap Ohio
Рет қаралды 26 МЛН