Set Garage Door Travel Max up and Down Liftmaster MyQ

Рет қаралды 308,489

4 жыл бұрын

this video covers a very important thing to check. Do you want to make sure that your garage doors not over closing and damaging your wall brackets.
Steps:
1. Hold rectangle button- Beep
2. HOLD down the up arrow until it reaches desired height.
3. Push rectangle button
4. Hold down arrow until it’s one inch before closing
5. Press up arrow once (door will automatically go up to set height).
6. Push down arrow once (door will automatically close to set close level).
IF your garage opener does NOT say wifi, try this add on that will allow you to make it work amzn.to/3HLEBDw
LIftmaster remotes amzn.to/3MnRJlJ
Disclaimer, I am an amazon affiliate, and may receive a commission for the link, but you pay the same price

Пікірлер: 146

@buenobye_ 7 ай бұрын

OMG this video saved me $130 service call! Took me a whole 5 min to fix! Thank you so much!!!

@alejandroponce2136 5 ай бұрын

The absolute best video on how to adjust your garage door on youtube!!! Thank you sir

@rmuffin 3 жыл бұрын

Omg... Such a great tutorial. I live how you didn't take forever to explain useless stuff.

@leocortesart3349 18 күн бұрын

That's slick, because I'm troublshooting my opener and when I saw that YELLOW COBRA! I have an 04 Mach1 lol

@dannyjohnsonsgarage 18 күн бұрын

That’s cool. I also have a 2003 Mach 1 and stories on them kzfaq.info/get/bejne/mZ97q6d_srrZloU.htmlsi=vCXd0rAOwlxmx_DA

@davekirkpatrick5724 10 ай бұрын

Thanks for the tip about stopping the downward travel just above the floor. Your video is the only one that I saw that mentioned that. One video said you can use both arrows to fine tune the stopping points.

@dhill3769 Жыл бұрын

Danny, it's rare for me to find instructions on exactly what I need to know. Your video was exactly what I needed to finish installing wiring on the ceiling for my new table saw. Great Job!

@kellycoffey4501 2 жыл бұрын

Thanks for the tip about stopping an inch above the ground. That solved my GDO issue!

@davidrodstein4383 11 ай бұрын

Excellent tip about stopping the downward travel about an inch before hitting the ground. That’s crucial to keeping stress off the mounting bracket. My mounting bracket busted because someone who said it wrong and I had to reinstall it. This pro tip really saved today! Thanks, Danny

@mrsincredibell 2 жыл бұрын

Thanks! Your video helped me fix my door travel without paying for a service visit! I appreciate it!

@onewayproductions5423 11 ай бұрын

Perfect instructions for what I needed, Danny. You were short and to the point. Totally loved my problem. Thanks again!

@rmac1325 2 жыл бұрын

Terrific video. Helped me fix garage door issues in less than 10 minutes and saved me a lot of $$ for a service call

@thewahakid1944 10 ай бұрын

Danny you saved me at least $167 for a call charge they wanted for a 5 minute fix that you showed us. Also helped with the down door stress on the mounting bracket as mentioned before me.😀

@onesource81 11 ай бұрын

Had the opposite problem where it only closed 1/4 way. Used the button setup accordingly and the garage door is back in order, thank you good sir!

@nycsh00ter 2 жыл бұрын

Short, accurate, and to the point. Excellent!

@Twiddle_TV 2 жыл бұрын

Thank you man!! The installer had my door SLAMMING shut so hard.

@jimsillence1354 Жыл бұрын

Thank you. This video was a help. My opener started behaving funny following a power outage. One thing I will add, if you have an opener with a battery backup like mine and you’re trying to completely reboot, the unit you will have to pull the battery. I was going through the same sequence as on your video, but not getting the same result. So I figured a reboot would be a good idea. I unplugged the unit, but then remembered that I had a battery back up. It wasn’t until I disconnected the battery and then plugged the unit back in. Then got it to behave the way it should while resetting it.

@kimberlymoore415 11 ай бұрын

Perfect explanation! Fixed my garage door issues in under a minute

@darriusfreeman156 Жыл бұрын

Thanks! I replaced my garage door seal and ran into this problem. This solution saved me money.

@RAZORTUCKERSHORTS 7 күн бұрын

I just had that issue when I adjusted my liftmaster 8165w garage door opener when it over close I fixed my self with out this video

@RAZORTUCKERSHORTS 7 күн бұрын

When you over shut garage door on 8165w it won't shut

@dougcoartney8189 Жыл бұрын

Perfect! Following your instructions solved my problem.

@fr0z3nshade Жыл бұрын

First video that came up. Straight to the point and I nailed it on my first attempt.

@rectorpineda9069 6 ай бұрын

Thank you for your video. I finally fixed my garage door. Excellent instructions and I learned a lot.

@TDot_SSB Жыл бұрын

Garage door got froze to the ground in the winter and messed up the calibration. This helped me fix it in 5 minutes. Thanks!

@arwong222 Жыл бұрын

This info is still relevant in 2022! Thanks for the video!

@gerardohuerta6925 5 ай бұрын

Hell yes! Thank you man I was able to fix my garage door with this video! Saved me some $$$$$

@dennissmith1510 Жыл бұрын

Straight and to the point, thank you Sir!

@corsair419 Жыл бұрын

This was literally exactly what I needed, thank you!

@sheatg2630 2 жыл бұрын

Neat explanation for a layman to understand. Thank you Danny!

@BakouMOH Жыл бұрын

aw,,0 ,,

@Sonic-dk2wx Жыл бұрын

Great guide, really saved me in a pinch. Thanks!

@beastlybryan11 2 ай бұрын

This is exactly what I needed for mine. Thank you!! 🙏

@johngriffith1096 2 жыл бұрын

Thanks. Straight to the point.

@cuttycheeks 6 ай бұрын

Great instructions! Got mine adjusted after 3 attempts 😁

@edwardasher2110 10 ай бұрын

Thank You So Much For Posting This !!!!! Perfect Instructions !!

@raymondhughley3200 Жыл бұрын

Simple and to the point! This video really helped, great job.

@Nelly_AB 3 жыл бұрын

Thank you very much for posting this. It was exactly what I was looking for.

@dannyjohnsonsgarage 3 жыл бұрын

I’m glad you found the video!

@in1nae 3 жыл бұрын

Thank you!! our garage door is bowing, and I am hoping this will help solve the issue!

@prithviraj2k Ай бұрын

Thank you so much!!!! Worked perfectly

@ishconsult Жыл бұрын

Video was extremely helpful. I replaced the T bar seal on the bottom of the door and the door wouldn’t stay closed. I followed your video to the letter and bingo! It now works perfectly! Thank you very much.

@urheiness7 Жыл бұрын

I have a gap on the bottom of the door how do I fix this

@ishconsult Жыл бұрын

@@urheiness7 Sorry, but I'm not the guy you should be asking for advise on your gap at the bottom of the door; I'm just a guy that followed the instructions provided by the video. I suggest you either ask the video provider your question or look for a video that talks to 'gap at bottom of garage door'.

@03hVc01 5 ай бұрын

You're the hero we deserve!

@eyuelgessesewolderufael4602 2 ай бұрын

Omg - you saved my day man!! Thanks a lot for sharing.

@The-Reflex331 4 ай бұрын

Thanx for posting this!

@beckyjohnson1793 Жыл бұрын

Bro!! You’re a lifesaver!!! Thank you! Easy peasy!!!

@markfichera3527 7 ай бұрын

Thanks For the Easy Instructions man

@BozzleyOfficial 2 жыл бұрын

You’re a saint. Subscribed.

@ChitownRon 2 жыл бұрын

Great instructions worked out perfect.

@kvn6776 4 ай бұрын

Thank you very much for the video!😅

@aschroer Жыл бұрын

This also works for the side mounted opener. Thanks man

@MrBillCNW 4 жыл бұрын

Thank you for sharing the video it was very helpful, I appreciate it. Thank you

@marksandorf2072 4 ай бұрын

Super easy, thanks !

@ramsaybolton9099 10 ай бұрын

Thanks, worked perfectly.

@UmayNoMe 2 жыл бұрын

FYI folks.....great video in deed.... However if you go up and down to many times to set the limits the motor can get hot and protect itself and shut off. I learned the hard way to wait 30 min and try again after the repair man was out telling me nothing was wrong, but it was over heated lol.

@scottrayhons2537 6 ай бұрын

The 1/2 horsepower motor must be a Shetland pony instead of a Clydesdale horse.

@therealstevenou Жыл бұрын

You fixed my excessive force error. Thanks!

@SundaramV85 8 ай бұрын

Short and very useful video

@EnlightenedRealm 10 ай бұрын

Excellent man!!! Thanks for your help

@d.l.9517 Жыл бұрын

Nice tutorial and nicer Cobra 👍🏻

@troyaltyyy Жыл бұрын

this was perfect thank you!

@srairmand 8 ай бұрын

Thanks a bunch. I did that and it worked.

@TheChris1299100 Жыл бұрын

Thanks! This really helped!

@andrewwiener6798 6 ай бұрын

Great video!

@sertifiedmusic6466 7 ай бұрын

Thank you so freaking much!!

@TOWNCARBUBBA87 Жыл бұрын

Thanks brother very informative 👍

@kirkgreenman1386 Жыл бұрын

Nice and Quick, Thank you.

@SMTBCM Жыл бұрын

Thank you, very helpful.

@craigradebaugh4634 2 жыл бұрын

It worked. Thank you very much.

@user-yw1mf5cb3x 5 ай бұрын

Thank You so much for posting this. perfectly done sir, I owe you a beer !!!

@thurm101 Жыл бұрын

This is great. Because I let the down area nearly touch the bottom. But on the down it still goes a little bit. I will try this.

@eizenkrein 2 ай бұрын

This is exactly what I’m looking for.

@gwmgbwi 3 жыл бұрын

Yep, that did it. Thank you!

@22joshuaryan 2 жыл бұрын

Dudeeeeee thanks so much !!!!!! Life saver !!

@TheTreeTuner 8 сағат бұрын

Most excellent! Thank you.

@pratapbob1 Жыл бұрын

Thanks for the video. I had an issue where the trolley was jammed up against the safety bolt on the rail close to opener unit. Had to remove the chain altogether to release the tension between jammed area and sprocket, and tried this adjustment. It did not register the up down limits properly. Found from this video and the liftmaster manual, that the trolley should be taken closer to the door and attached to the arm so that the calibration should always begin when door is closed. Setting the limits from door in closed position worked great

@tizlaney Жыл бұрын

This exact same thing happened to me - however, I am able to set the upper and lower limits - but on the test run (final 2 steps) it travels up and stops at the open limit (opens) and then on traveling down (closed) it goes about 1/3 of the way and stops - giving me an audible alert of 5 beeps. I have verified that there is nothing binding, in the path of the door closing - and everything appears to be adjusted EXACTLY as my other garage door (10 feet away). Any advice?

@ejreyes3442 3 ай бұрын

Thank you very much.

@Firebird400 2 жыл бұрын

Thanks man . Nice cobra btw !

@orsonwhite8830 Жыл бұрын

Thanks so much!!

@johngriffith1096 2 жыл бұрын

Thanks. Great vid. U the man.

@champnessjack1154 Жыл бұрын

Perfect, thank you.

@brianb.4535 Жыл бұрын

Awesome just fixed a garage door gap!

@cg3399 5 ай бұрын

Completely lost concentration when i saw your Terminator 🤤😩🙌

@DixieGolfSTG 2 жыл бұрын

Very helpful. Thank you!

@dannyjohnsonsgarage 2 жыл бұрын

Oh, hey Aaron 👋🏼

@ryan4carvids 3 ай бұрын

Bro THANK YOU😂. MONTHS of agony!

@robertvigil9396 10 ай бұрын

Thanks!

@Marinetuck220 2 жыл бұрын

Perfect thanks. Can't rely on apt maintenance to do anything right.

@johnschottler1424 2 жыл бұрын

Dude thank you. I was soooo annoyed. My garage was only closing like two feet lol.

@caroleb3098 Жыл бұрын

Thank you...

@TheIlldill 7 ай бұрын

The cobra! 🔥

@Raul69 Жыл бұрын

Thanks 👍👍👍

@randomrazr Жыл бұрын

if i just wanted to adjust the down position. can o just do that or do i need to do both?

@ohioridgerunner7497 8 ай бұрын

Having issue with my door and no luck locating owners manual ,8 year old liftmaster your video fixed me up saved a service call probably in the 90 to 120 dollar range .thanks again

@pearsonchuck 10 ай бұрын

thanks so much.. You save me a lot of frustration and maybe even a marriage

@thomasplower367 8 ай бұрын

Glad I found this. Had the exact same problem.

@gradientgamer5480 Жыл бұрын

i like the 2 step system. 1st step: program limits 2nd step: program force

@Michagan_outdoorsman_James 4 жыл бұрын

hey man wanted to tell you guys to have a safe and happy thanksgiving. in case you dont post another vid before then

@dannyjohnsonsgarage 4 жыл бұрын

Thanks! You too 🙌🏼

@alvaro1728 2 жыл бұрын

What if I only need to adjust how far up it goes? It's already going down fine so I don't want to mess with that. Thanks!

@mustafael-amin9163 4 ай бұрын

I have a chamberlain and I think I need a travel module a/o logic board replacement.I’ve done the troubleshooting codes but to no avail.Any suggestions?

@dmfgthehog9058 8 ай бұрын

When I try to do the travel adjustments the light doesn't beep or flash to initiate the adjustment..help

@orlandot3944 Жыл бұрын

No waste of time, perfectly explained. Some top g shit.

@matt_arco 10 ай бұрын

for some reason after i set the limits on mine i press up to test how far i set it to go up and it will only go halfway up, i tried like 5 or 10 times and cant get it to work correctly after i set it, im not sure why, any tips would be appreciated

@JPerez-ld6nb 7 ай бұрын

Thanks for the video. It helped me 100%. I just bought this home the previous owners didn’t give me the code for the pin pad. I wanted to reprogram it and also reprogram the 2 controllers. It has a second attached garage. That one doesn’t have a pin pad but I only have 1 controller for that one. I don’t know if they lost the other one, if it only comes with 1 control or if they took the other control. That’s why I want to reprogram everything. Do you have a video on how to do that?

@dannyjohnsonsgarage 7 ай бұрын

I have a few programming ones. I think the only one that talks about erasing old ones is for the car kzfaq.info/sun/PLIjr-uSYDZi5xpo7t07I8aY2FnZcPEq_W&si=plVSeWITV7cpU5gd