SH .28 P3 Nitro engine rebuild.

Рет қаралды 4,022

thebug 404

Жыл бұрын

Пікірлер: 97

@MikeGray-ct6hb 5 ай бұрын

Personally I'm more of an electric guy than nitro but I watch your videos solely for the crazy shit you say! Love it!

@thebug4046 5 ай бұрын

Haha thanks for stickin around! And yeah a lot of people lent the crass humor 😆💯🍻

@ofnaguycarlwatts8602 Жыл бұрын

Great video Buddy. Might be old and boring.But to your true supporter as I should say.We can't wait till the next video no matter what!! 👍 👍 👍

@thebug4046 Жыл бұрын

Hell yeah buddy! Speaking of which one you're going to start posting some more videos hopefully you're feeling better!

@Nitro-Aaron31 Жыл бұрын

Thank you for video bug and I love the humor! Now I know how to replace bearings man thank you again.

@thebug4046 Жыл бұрын

Your very welcome! Glad you had a Laugh and that it helped ya! 💯🤘🏻🍻

@hpiedsavageed7608 Жыл бұрын

Badass! Can't wait for more vids to come! Kbn!

@thebug4046 Жыл бұрын

A few more days until my new pipe comes in and I will start it up on camera for the 1st time stayed tuned!

@tylerteaka1026 Жыл бұрын

I love your videos! Way to let those snowflakes have it! I just stumbled across your channel and subscribed in like a min. Bonus that your a fellow Canadian. Cheers

@thebug4046 Жыл бұрын

Hey thank you very much for subscribing I really appreciate it and yeah unfortunately there's a lot of lame people out there these days! Haha what part of Canada you in?

@Southwest.rc.bashers Жыл бұрын

Nice work m8

@Southwest.rc.bashers Жыл бұрын

Cracks me up when you say about the environment so funny your a legend 😂😂😂😂

@OmarGreeneotraPedroVerde Жыл бұрын

I realize this is a bit childish, but first! Now, I shall watch intensely.

@thebug4046 Жыл бұрын

Hahaha 1st the worst 2nd the best! 🤣🤣

@joeosmulski5172 Жыл бұрын

Thanks great info.

@thebug4046 Жыл бұрын

Anything! 💯🍻🤘🏻

@thomasmattos1493 Жыл бұрын

Good trick to get those bearings out get it on hot plate like you cooked pancakes on said the block on end set it to 400° walk away go do something for 10 minutes or so come back in the bearings would be laying on the hot same goes for putting them in freeze the bearings lay the block on the hot plate they drop in and when everything comes temperature in nice and tight

@thebug4046 Жыл бұрын

Holy crap haha at least it worked!

@thomasmattos1493 Жыл бұрын

That's also how I get crankcase bearings and cylinder sleeves out of motorcycle engines

@thebug4046 Жыл бұрын

@@thomasmattos1493 yup! Same stuff just smaller

@cheri758 11 ай бұрын

There is pistons in your video now! 😂😂😂

@thebug4046 11 ай бұрын

Many lol

@mikeh.748 Жыл бұрын

Excellent video bug. I find your humor hilarious. The part about not discriminating and hating everyone equally reminds me of an ex coworker.😂 Use a screwdriver on all pull starters when removing them? They’re all alike as far as that goes ( beginning of video)? Feel free to throw all them little helpful hints out there you can.

@thebug4046 Жыл бұрын

Hey man it's just a good idea because sometimes they can come apart on you and it's kind of annoying when that happens especially if you're not really good with rewinding them it's just a safety precaution really

@wildedaveable Жыл бұрын

Man, ALL your videos are so helpful, I'm one of them old guys that's been in the Rc world since the early '80's. Just got into nitro and every question I have had you have answered in your videos. Love the humor too. I have a question for you. I recently acquired a Redcat Hurricane xtr with the SH 28, I found an abc sleeve and piston and a rear bearing, however I cannot seem to locate the front bearing - where can i find one please? Thanks You Rock.

@thebug4046 Жыл бұрын

Hey thank you very much for the kind words I really appreciate it and that is a 607-2RS front bearing order one for nitro engines AVID or Acer bearings will have it eBay usually 🍻💥👌🏻🤘🏻

@wildedaveable 11 ай бұрын

@@thebug4046 Thank You! You Rock! I have been telling all my buddies to watch your videos because there just are not any other RC videos that compare to yours man, you are The Master! Thanks Again 👍

@thebug4046 11 ай бұрын

@@wildedaveable thanks brotha I appreciate it very much! I am also admin in the Nitro RC enthusiasts group on Facebook if you guys wanna check it out. I try to keep my videos as real and to the point as possible. So many other channels that are 90% nonsense then barley touch on the subject usually with poor advice. 🍻💯🤘🏻

@supremecapone Жыл бұрын

I’m sooo offended hahah how can anyone be offended great video man!! Enjoyed it

@thebug4046 Жыл бұрын

Hey thanks for watchin! 🤣👌🏻🍻🤘🏻💯

@th3duke1 Жыл бұрын

New subscriber from the Ottawa/Gatineau area - love your videos. I'm curious, do you have a preferred place that you buy your engine parts from (in Canada)?

@thebug4046 Жыл бұрын

Thanks for the sub! And I'm over in the Vancouver area. And sadly not. Most of them just sell Traxxas so I gotta buy a lot of my parts from the US or over seas unfortunately

@hunterdurst4571 Жыл бұрын

What’s your opinion on a SH.12 building another Traxxas Nitro Sport and want to change some things up a little with motors. Another great video as always!

@thebug4046 Жыл бұрын

If you can make the adoption it's a good engine they perform quite well and they're pretty cheap for parts too!

@josephwatkins2335 Жыл бұрын

Pistons are Pistons!

@josephwatkins2335 Жыл бұрын

I like to cook mine in the oven.

@thebug4046 Жыл бұрын

Electricity is expensive and I didn't feel like waiting that long lol

@Thedudeabides803 Жыл бұрын

Have you ever pinched a sleeve? I have three I didn’t throw away and I have been meaning to try it. One guy used a small band clamp, heated the crap out of it and quenched it. Seems like a hell of a trick.

@thebug4046 Жыл бұрын

If sometimes you can buy pinching tools on eBay but You have to make a sleeve ring so you will get it round and pinched in the right spot otherwise the piston will never go all the way into the cylinder again. It's something I'm gonna do some experimenting with at a later date

@charvelgaming2975 Жыл бұрын

Fantastic video. Let me first I love the humor 100%. I had a nitro engine sitting too long due to a move. Took it apart and got some measurements to replace a few internal parts. Can you recommend a good supplier in US for bearings, piston rod and sleeves? New sub by the way.

@thebug4046 Жыл бұрын

Hey thank you very much for the subscription I really appreciate it and could you be a little bit more specific on what engine it is exactly you're dealing with because sometimes a lot of these things cross over but I need to know of the make and model! And Raw negative humor is my thing haha 👌🏻🤣🍻

@charvelgaming2975 Жыл бұрын

@thebug4046 Thanks for the response. I'm working on a Fusion X engine. I can't tell which variant it is there's no other visible markings to identify it. Rctech page has a long thread showing various models. I'm looking to replace bearings and piston/sleeve. Hope that helps

@thebug4046 Жыл бұрын

@@charvelgaming2975 I haven't heard of that model before but what I can suggest is going on Facebook and looking for the Nitro RC enthusiast group I am an admin in there post up your photo and I'm sure one of us can figure it out! See you there!

@charvelgaming2975 Жыл бұрын

@thebug4046 Awesome I'll do that right away. Thanks for the help amigo

@charvelgaming2975 Жыл бұрын

@@thebug4046 I requested to join the page look for Mark C. I was able to remove the bearings. I just need to buy them and get the engine squeaky clean for the rebuild

@revtech2917 Жыл бұрын

Hey man. Have you ever heard of buku? If you have what’s your opinion on their products? I have their clutch and it’s amazing but I was wondering what you think of those crank case caps they sell? They’re supposed to help prevent air leaks from the front bearing. I seen on Google that people are worried the grease could get sucked into the bearing and make things worse. (Btw I have ceramic bearings all round in my unbroken-in 3.3.)

@thebug4046 Жыл бұрын

Honestly in my 23 years and the hobby have never had any other products so I can't really comment too much on that you're not to ask in the Nitro RC enthusiast group on Facebook.

@cassianomartin2699 Жыл бұрын

What's the deal with the paper towel lol, someone said it's going to scratch piston sleeves? 🤣

@thebug4046 Жыл бұрын

Some a** clown that says that if you use paper towel on any kind of engine parts they will instantly self destruct the guy was retarded probably a locked of Earth as well...

@cassianomartin2699 Жыл бұрын

@@thebug4046 hahaha 🤣

@jimmygeorge4268 Жыл бұрын

JUST a curious question…will a heat gun have the same effect heating a block to remove bearings or do you need direct flame ,,like the butane flame you use? I have both. Thanks….

@thebug4046 Жыл бұрын

Yup! Sure will

@robertfarnham3652 Жыл бұрын

I use purple power cleaner to you and to clean my nitro engines in my parents it works fine it works great it does not hurt and get some nice and shiny and maybe so don't be so rude

@thebug4046 Жыл бұрын

I'm not being rude in my video I'm just stating that some people don't know how to use certain products and will destroy their parts and come back and complain about it.

@KineRC 4 ай бұрын

heh.. just googled a engine i had , and guess whos video popped up ..bug! , nice ... what part # is the piston kit for this? is it still available? mine actually runs but i was wondering if parts were available

@thebug4046 4 ай бұрын

Hey man thanks for watchin! And order the piston and sleeve kit pin and rod for the Dynamite big red. It's an upgrade for the 28P3 engine. No modifications required. amain hobby should have everything you need. The SH 28P3 is basically the exact same as the dynamite big red. Different look and Different ports that's it.

@hunterdurst4571 Жыл бұрын

As for the bearings did you factory SH Bearings and are they good? or another brand, heard in another one of your videos that Fast Eddy bearings quality is going down hill. What brand bearings would you recommend. Thanks!!!

@thebug4046 Жыл бұрын

I used a ceramic rearbearing in a steel front NTN front and Acer rear. And yeah I don't run Fast Eddie anymore unless there's something like wheel bearings I do not put them in engines I've had too many failures and seen too many come apart they are very soft cheap stainless steel bearings which do not put up with the extreme heat and rpm of these engines

@hunterdurst4571 Жыл бұрын

@@thebug4046 I definitely will have to change mine out then I don’t want any catastrophic failures to happen, thanks for getting back to me, I appreciate it. Killer content as always just got done binge watching your videos haha

@thebug4046 Жыл бұрын

@@hunterdurst4571 NTN bearings are awesome AVID is really good to lots of em out there just do a little research before buying to make sure you get top notch! Glad the videos help ya! 🍻🤘🏻💯

@dancj10 7 ай бұрын

What engine mount you using for the .28? Been trying to find a engine mount for a .21 sh off road competition engine.... putting it on my tmaxx 3.3

@thebug4046 7 ай бұрын

This engine is for my HPI savage X 4.6 there is no big block tmaxx stuff available anymore. And it was expensive to do it because nothing fits since everything has to be upgraded in order to made it work. The best thing to do is return that engine and just buy an OS 21TM it is designed for Traxxas cars and trucks. Just be sure it says for Tmaxx! Because the revo engine is different! The tmaxx engine is plug and play no modifications or special parts required and it's an os so it's already better quality

@dancj10 7 ай бұрын

@thebug4046 I thought so, but I'll just upgrade my 1/8 Buggy then. Swap my newer engine in that instead. I guess nothing was all lost lol. I did just buy the OS 21TM for the tmaxx for sure. Just wanted a something a little better than those 3.3 traxxas makes that are kinda crap. 320 bucks later, but hey nothing is all lost. All still win for me anyways since I was gonna upgrade my 1/8 Buggy that has the 3.0 kyosho. Thanks again for the reply!!

@thebug4046 7 ай бұрын

@@dancj10 you will like the 21tm they run awesome much better then the 3.3 and they last a really long time! Just take your time on the break in the os is a tight engine and takes more than then 6 tanks Traxxas says to use. Preheat is a must!

@ollination 7 ай бұрын

Where do you happen to get your replacement parts from for example HPI nitro star 3.0 parts?

@thebug4046 7 ай бұрын

EBay

@ShadowOppsRC Жыл бұрын

I did a abc upgrade to an sh18 but it needed rebuilt. Might have been me but I did not film it. Burn out on making content.

@thebug4046 Жыл бұрын

The 18 with the ABC upgrade is a really great runner and yeah I agree coming up with content can be difficult there's nothing worse than forcing it. it's like trying to force a fart it can be shit. 🤣

@ShadowOppsRC Жыл бұрын

@@thebug4046 lol and the corrisponding code brown moment from forcing!

@thebug4046 Жыл бұрын

@@ShadowOppsRC hahaha! That's awesome

@irony4057 Жыл бұрын

Bit of an odd question... and I would prefer to ask people who really spend time with nitro motors to get opinions from... I have a Cen Genesis 7.7 motor finally gave out and while i will replace the piston and sleeve at some point, at the moment I have all kinds of nitro motors but little funds to order replacement parts. I was going to ask if you or anyone else watching could give an honest opinion... I have 3 motors I have been thinking of using as temp replacements to enjoy the truck again. I have an Axial .32RR, a Losi 454, and an Ofna .32. Do you think any of these will have the.... clout? to push a truck that big?

@thebug4046 Жыл бұрын

I'm not sure exactly what you're dealing with here so the best thing to do would be share pictures and videos in the Nitro RC enthusiast group on Facebook I'm an admin in there answer the 3 questions I will see you there that's the easiest way to get help. 🍻🤘🏻

@irony4057 Жыл бұрын

@@thebug4046 I'm actually probably a part of it I'll see what I can drum up for most effective pics

@thebug4046 Жыл бұрын

@@irony4057 My apologies I wish I could help you more I know what super annoying when you can't find what you're looking for.

@irony4057 Жыл бұрын

@@thebug4046 yeah but truth be told the way I'm looking at it is there isn't really a 100% correct answer. It's something that is open to opinion as much as experience. The Cen is a brute of a truck in size and weight and because of that the motor had to follow suite.. and when moving away from stock its a mix bag, same say it should have come with a completely different setup some back the stock as it's tried and true.

@ShadowOppsRC Жыл бұрын

I am in the process of rebuilding a big red and have a few questions about things. Could email you off youtube?

@thebug4046 Жыл бұрын

What's up? And hit me up on fartbook I'm an admin in nitro rc enthusiasts group. You will see a lot of the same videos and posts as here. The big red is very easy to re&re it's the same process as the p3 same bearing crank etc.

@ShadowOppsRC Жыл бұрын

@@thebug4046 Most of the parts are not available for big red right now so doing a sh 28 pro hybrid but cannot find anything about what shims and rod and wrist pin. Got a good used block case and cooling head with crab and not internals or button head. Have most but running into a wall about the shims.

@chriskopecky995 Жыл бұрын

What bearing sizes for front and rear ?

@thebug4046 Жыл бұрын

Hang on

@thebug4046 Жыл бұрын

13x24x6 and the front is a 607-2RS I believe

@chriskopecky995 Жыл бұрын

@@thebug4046 Dynamite BigRed.28 bearings would fit to ?

@thebug4046 Жыл бұрын

@@chriskopecky995 same block crank and all that yup they will fit. Basically they are the same engine aside from color and port work

@Thunder_Road_81780 Жыл бұрын

What the hell is a piston lol 😂👊🛠️💪

@thebug4046 Жыл бұрын

No idea but apparently I didn't show any pistons in my videos 🤷🏻‍♂️🤣

@mohammadalsharif5409 Жыл бұрын

Please can I use it for a plane

@thebug4046 Жыл бұрын

An SH 28?

@mohammadalsharif5409 Жыл бұрын

@@thebug4046 yes SH28

@thebug4046 Жыл бұрын

@@mohammadalsharif5409 it's not for airplanes buy an airplane engine

@josemanrique9860 Жыл бұрын

Hey I have a motor with broken cranckshaft can I send it to you so you can fix it...not expecting freebies

@thebug4046 Жыл бұрын

Hey man what engine do you have? I can walk you through it. Shipping back and forth might be more than you will want to spend depending on where you live. Check out the Nitro RC enthusiasts group on Facebook. I'm the admin the the dark sunglasses. Be sure to answer the 3 questions posed up a picture and I will see if I can get you sorted out 👊🏻🍻

@josemanrique9860 Жыл бұрын

@@thebug4046 that's the thing I got a hobao hyper SS cage 1/8 but motor I dont think is original the heat sink say jl but motor doesn't say anything I think is a ofna ( discontinued)

@josemanrique9860 Жыл бұрын

I actually I been posting on your page

@thebug4046 Жыл бұрын

@@josemanrique9860 New engines are relatively cheap you can pick up a Mac .28 for like 140 bucks there was a lot of engines marked ofna but were made by other manufacturers. And I haven't seen anything regarding it yet. But I will keep an eye out for the post

@josemanrique9860 Жыл бұрын

@@thebug4046 I'm posting on ur page now and yes I got a dynamite .28