Shallow Well Pump Replacement // Easy DIY // Harbor Freight Special // Drummond 1HP Combo

Рет қаралды 17,135

8 ай бұрын

The pump on the good ol well finally died. It was cheaper to go ahead and replace it with another like model versus buying just the pump itself. This is a very easy DIY project for those who have a well, but paid someone else to put it in. If your pump fails, follow this quick video to see how easy it is to remove a hose and replace it onto a new one. Save yourself a little money.

Пікірлер: 31

@russwoodward8251 Ай бұрын

Just bought one of these to pressurize my irrigation. I also have just the pump for extracting from the pond. Thanks. Really informative.

@squank252 Ай бұрын

I really enjoy mine. Fantastic little setup for a cheap price compared to others on the market. I use mine daily.

@19Bmiller 2 ай бұрын

You did very well explaining all the steps. Thanks

@squank252 2 ай бұрын

Thanks Bob! I forgot to show that there is a small circle cover on the side of the tank that pulls off. That is where you connect your air hose to pressurize the tank. I just fill it with water and it works. Been pulling strong to water my flowers, garden, filled my pool, fill my chicken water, and apple trees.

@compactinfinity 25 күн бұрын

You can also prime it from the top of the spigot. The plug is for people who have different setups in which you cant fill from the outlet.

@squank252 25 күн бұрын

Last two I setup here at this well, I filled from the spigot. It took a little more time but easier to me. Opened the spigot, or fill plug, fill it up until it starts to run back out, let it rip. Took about 5 seconds and it started sucking from the bottom perfectly.

@compactinfinity 25 күн бұрын

@@squank252 it is a good fn pump for sure.

@niceride 29 күн бұрын

Adding some data to videos about this pump and tank combo: I've measured with a fluke clamp meter the inrush/max as 40A 120Vac.

@squank252 28 күн бұрын

Thanks

@imaslowlerner 7 ай бұрын

The rear of the tank has a sharader valve fitting where you're supposed to pressurize with air up to 23#.

@squank252 7 ай бұрын

Good to know. Figured there had to be a better way to properly pressurize it!

@TiredOldMann 4 ай бұрын

I have the same as the New Pump . The black box on top has a start capacitator you can replace when it goes bad . $10 . The bladder inside my tank went bad at 2 years old . To avoid burning out the motor and start capacitator unplug the pump , open the water valve and add air to the back of the tank . Black round plastic thing on the back on the tank unscrews showing a tire air valve . The pressure gage should drop to 20 psi . Close water valve . add air to 40 psi .I have to add air every two days . I'm sure the bladder can be replaced but I'm too lazy to try it . Have fun ....

@squank252 4 ай бұрын

Yeah I agree. I could have probably taken this motor completely apart and replaced a bad bearing but for the cost I just assume to replace it. If I can get me a couple of years out of it then I’m happy. I put mine through plenty of good use.

@balamusadanso7074 4 ай бұрын

Amazing booster

@squank252 4 ай бұрын

Yep

@19Bmiller 2 ай бұрын

Thanks

@squank252 Ай бұрын

Welcome

@JoseRomero-rb5fv 3 ай бұрын

23psi on the air tank that you have to fill up with air

@squank252 3 ай бұрын

Yes. There’s a plug on the side. Have to unscrew the cover. I just fill it with water and it seems to work just fine.

@thepuma167 Ай бұрын

How deep is this thing pulling ?? And what’s on the bottom of the 1” pipe that’s in the well casing

@squank252 Ай бұрын

The actual hole is roughly 26’ deep from ground to tip of point. Is schedule 40 piping, the thicker pipe, inside couplings you can find in well sections of stores, and at the bottom is a slitted well point I got from Lowe’s.

@user-jg9rg5zz4e 5 ай бұрын

You may just need a new capacitor on the old pump

@squank252 5 ай бұрын

Not sure. It was given to me and to be honest I had no idea how old it was. It was fun to replace it.

@djemsmortimer 5 ай бұрын

Can you use flexibility pex instead of PVC?

@squank252 5 ай бұрын

Have to check the ratings I imagine. This is a schedule 40 piping for a higher pressure rating. It’s thicker walled compared to the regular pvc. Also I’m not sure if the sun would eat it up over time or if it’s UV resistant.

@msanc315 26 күн бұрын

Can it be hard wired instead of using the cord

@squank252 26 күн бұрын

I’m sure it could if you don’t mind cutting the plug off and splicing together or removing the short cord from the box on the pump, then hardwiring directly there. I left the plug and just used outdoor grade boxes to have the ability to plug other things out there. (Lights, tools, etc)

@rafaelsandoval7077 12 күн бұрын

I think is your pressure switch. That's bad on your old pump cuz it's just humming not getting enough ground

@squank252 11 күн бұрын

I’m not sure honestly. It functions off of water pressure. If it was defective and electrical I feel like it would have continued to pump water around to repressurize. My new one has done the same thing on the gauge. Lowes sells them pretty cheap. Nothing to them. Just unscrew and screw the new one in. Not really a switch. My new pump, works great and the gauge has done the same thing. Just a cheap gauge I think.

@joserefe5950 3 ай бұрын

Symptom like that means the us$5 capacitor is busted.

@squank252 3 ай бұрын

Could be. The original was given to me. I wasn’t sure what the wear was on it. It was loud and horrible sounding but it worked. Lasted a good while. I wanted a new one and found one on a good price. Plus it was fun and gave me something to do!