Thank you 🙂

Thanks very much for your support

Cheers im glad you liked it 😊 spread the word 😀

Thank you very much 🙂

Thanks Jay 😊

🤣 Batman was a millionaire do I'm not 🤣🤣

Thanks 🙂

Thank you very much

Thank you

Thank you

Thank you very much and welcome to the channel 🙂

Thanks very much for your support

Thank you very much

Thank you 🙂

Thank you and welcome to the channel 🙂

Thanks

Thank you very much 🙂

Thank you 🙂

Thank you very much 😊

Thanks, it's very simple and works a treat 🙂

Thanks very much for your support

Thanks 🙂

Thank you very much

Thank you very much 🙂

Thanks very much for your support

Thank you very much 😊. It not easy starting on here

Thanks and welcome to the channel 🙂

Thank you

Thank you very much 😊

Thanks very much John 😀

Thank you, I plan on upgrading that jig in the future and will video it

Thanks very much for your support

Thank you very much 🙂

Do u have plans to make these?

Thanks Keith 🙂

Thanks David 🙂 I totally agree 👍

Thank you very much 🙂

@ I’ve just subscribed Tommy so now I’m going to be binge watching your videos 👍🏻 please keep it up these are great

@@gdmonks1959 thanks Gary and welcome to the channel

Thank you

Thank you very much for your support. This was my first ever youtube video I think they are getting better everytime 🙂

@ you're right, they are beter! 👍 Saw already a few more.

Thanks Paul, sadly I didn't video setting up the system but I will try to cover it at some stage as part of the workshop tour series

Thanks very much for your support

Hi Kieran and welcome to the channel. The short answer is yes I have considered holding classes or 1on1 tuition but unfortunately the figures just don't add up with insurance etc.

Thank you hopefully it wont take me 32 years to get the editing tight lol

@ God no, its easy ! Just remember, the first frame after the action finishes is when you cut. If you keep it moving at a good pace you'll keep your viewers. Good luck and keep it coming

Thank you very much 🙂

Hi, it's a Robland Z320 panel saw I wouldn't call it compact but it is a fantastic machine. I have a quick overview video about it on my channel

@ Great thanks 👍🏻

Thank you for your support and feedback. I'm still getting used to speaking to a camera and trying to get the right angles its kinda trial and error at the moment. The sound definitely does have an echo as its a pretty big workshop I hope when finances allow to upgrade to a wireless microphone which will hopefully address this issue 🙂

@ No worries, it's a big step to go from working to working and filming. You do not display any of the usual "first time video" jitters and such that most people do, you seem more than less comfortable in front of the lens, and that is HUGE. Angles/lighting/audio, that all comes with time. As far as the looking up goes - I assume that your camera is a good meter + away from you, at least based on the field of view etc, just try looking at the bottom of the camera as opposed tot he center of the lens - of course, you can't drop your gaze too far or it will look like you are looking at someone or something behind the camera. Do a test shot - pic say 3 points, the 1 you are using now, as you are clearly looking at the same eye-contact target each time, and then 2 more marginally lower, one below the other. - then start recording and run through your intro 3x once at each focal point .. when you review the footage it should be obvious which one looks best, or at least where you should then look for #4. It's like taking a selfie - I can never quite get them right. Honestly, that was the only technical sort of issue that struck me, and the echo as you noted, equipment will do a bunch for you, using the mic on the cameras makes it hard to clip out certain effects of the space. All in good time Sir, all in good time.... don't go driving yourself bonkers over it, focus on your content and you'll do fine as a channel

Hi, it's a robland z320 I have a video giving an overview of the saw

Hi Wayne, yes you could use 1/2" mdf but you will have less support for the pvc pipe so the pipe may need to be glued in place. Any 1/4" stable material can be used for the gate (mdf,hardboard,ply or even plexiglass) I have never had any issues with wood glue affecting mdf. Hope this helps

@ Thank you very much. Off I go to get some 1/2" plywood. Thanks for the quick reply. :)

I used 4" pvc ventilation pipe fits perfectly inside the 4" sewer pipe and flexible pipe fits over it perfectly too.

@ Well, lucky you.. The Sewer pipe we have here in the US is called Sewer Drain and Vent. I can't find anything but galvanized air duct that is a 4" OD.. Our Sewer pipe is: (Sewer Pipe ID:4.05" / OD:4.22") So, I would be looking for a 4" OD pipe to go "into" the Sewer Pipe, and again, the 4" OD for the Flex Hose to go over.. Strange. I would think there would be the same products in both Countries.. Like 3/4 and 18mm plywood, etc.. Maybe I am missing something, but, all of the charts I could find on Sched 20/40/80 are all based on the ID on the Pipe size.. Something is different if you can slide something inside of the Sewer Pipe and then on the other end slide the Flex Dust hose "Also an ID Product" over that.. Hmm.. Thank you though.. Still scratching my head... Ha..

@@MarkThomas123 that's unfortunate that you can't get 4"OD pipe over there so you are probably right I was lucky. One suggestion I can make is to make a kerf cut in your sewer pipe to allow it to reduce in size to 4" od and then glue the cut back together. It might sound a bit of a hassle but will get you sorted.

@ Yea. Weird. The only OD plastic/PVC pipe that is measured OD is a Central Vacuum hose 2" only OD.. You guys have a JIS K6741 and DIN 8062 Standard that gives you the 4" OD pipe. I found some 4" Hose Joining adapters that are tapered on both sides and have a thick body between. They look like they will heat and stretch on the one end, enough to fit into the Sewer Pipe.. If not, some wraps of Duct Tape will work. I wish we would all get on the same system... I am slowly adding metric measuring tools to my shop. Nuts/bolts/machine screws, drill bits, taps/dies.. Ha... Wish I would have done this years ago.. Another small fortune in expenses.. But, man is the metric system easy.. Ha.Ha.. Thanks for the video.. BTW.. This is a short blast gate that solves the self cleaning etc.. kzfaq.info/get/bejne/idF5ebObr7W1fok.html

Thank you 😊