Great video. One thing to note is the latest Marlin renamed BOARD_BIGTREE_SKR_V1_3 to BOARD_BTT_SKR_V1_3. That's what the error message said and after changing it, it works.

You saved my day too! I also had to remove the display because of alarm sounding

Original card worked AFTER I re-formatted it. It came up FAT, not FAT32. After a new card worked, I suspected something was different, and that's all I could see. Before reformatting the original to FAT32, it would never get to the "beep" after swapping the firmware and appearing as a drive. Now, beep! and looks great. Thank you for the tutorials.

You saved my day

thanks a lot from belgium you are the only one that gives good explanations on the net

Great Video Thank You For Sharing Worked Perfect For Me. I Was Having Max Bed Temp Error On Start Up and Couldn't Get The Sdcard To Read.

Thank you so much, great tutorial

Hello Edward, I am honestly a bit lost! I always use Ramps 1.4 but now I see more and more other boards floating above the surface. of course I am a stingy Dutchman! and wants the utmost for as little money as possible. maybe you can also tell a little more about the different plates and maybe something about price range. And yes of course I understand the more power the more expensive it becomes. Kind regards from the Rotterdam area! Rob.

Comment just to support your channel.Thank U!

Changing to a better quality card solved everything for me. The bundled card is rubbish.

Thank you!!

Super Video wie immer! Mach weiter so!

do I have to format in FAT32 32 kb clusters? apparently under 2gb you cant choose 32kb clusters, I personally cant and I was wondering if I need to

thanks

Great tutorial Thank You

Thank you so much!

I'm having the same issue as the other gentlemen had not so long ago. Everything else is going right except the bin file is not converting into the cur file. The jumper pins are correct to enable USB connection. Is it just a faulty board? Except for my lack of success, I commend you on your series of videos. Keep up the good work

Is it possible to flash mainboard from TFT screen. Say I have a SKR 1.4T with TFT 35 V2, Thanks.

Followed this to the letter and the SKR just buzzes non-stop now..... I noticed @5:45 that your platformio has more lines in it than the bugfix 2.0 download does too.... The download only has: src_dir = Marlin boards_dir = buildroot/share/PlatformIO/boards default_envs =

I know this is a old vid but I was wondering. Is there a way to upload firmware from the SD, TF, or USB port on the LCD screen instead of the one on the board itself? Like would a certain serial port assignment in the firmware allow this? It would make servicing the firmware much easier for those printers that have the boards enclosed to where you can not get to the ports without opening up the printer. I am currently waiting on some micro SD extenders I ordered to use to get around this issue as I use one on another printer but was curious if I could setup the printers to update firmware from my ports on the LCD screen. This thought came to mind as I am servicing my Kossel Mini and every time I want to update the firmware I have to take the print bed off.

Hi edward i cant find the files after i build the firmware i click on the navigation bar and nothing happen

Hi Edward. nice video. I have trouble with SKR Mini 1.1 When i insert the tf card, the board is loading, but not complete. Now the display just blank screen (previously installed marlin 2.0 is missing). What should i do? Is the board still can be used?

Hey Edward, running into some issues when compiling in Atom. It just gives a massive list of yellow errors then says build failed . Fresh install of atom with platform.io and a fresh download of marlin. Followed every single step exactly and not really sure why it's not working. Ever run into something like this?

Hello Edward, And another question? can you also connect an LCD 12864 to the SKR 1.3? could you show that in a video? friendly greetings from The Netherlands! Rob.

I really hope you can help me because so far no one can. When I place the firmware.bin file into my SD and load it into the SKR it never converts to the firmware.cur. My computer will no longer recognize the skr as a USB when I plug it in so I can’t power cycle via USB, I have to move the jumper to VOC and plug into my PSU and it still doesn’t convert to firmware.Cur. Any suggestions?

What example config should one use for the CR-10S4? The CR-10S one and mod up all sizes or the Cr-10S5 one and mod them down? (guessing the latter as I think the S4 and S5 have a different Y stepper motor than the smaller ones?)

Dear Edward, i setup marlin and installed on the board as you explain on videos. I am experiencing the issue that it wont connet to pronterface via USB. I configured line 105 on configuration.h as -1 but it still dont work. Motors, hotend, thermistors, display, everything is working but i cant connet the board to the PC via USB. Do you have some tips to help me? thaks.

Thanks for this.. But is the same.. Nothing.. Switch with a new microSD format install the .cur file and nothing.. The board only worked the first time.. After update the firmware... But.. I used the marlin 2.0.x from the github of bigtreetech and not of marlin.. I download now from marlin and now the card appears... Not yet configured but now shows... Maybe the marlin of bigtreetech from github is with some problem?

I love your videos. They have been very helpful, but i’m having an issue. I’ve compiled new firmware with some changes in config.h and trying it load them on the board. First issue was the pc wouldn’t recognize the sd card. Was this just a bad card that came with the board that i’ve read so much about? Anyway, i bought a new card, copied the new bin file to the card, and off course the board didn’t update to the new bin file. I found this video and have followed it to a T and the board still will not update. Maybe i’m missing something but i don’t know what. It’s as if it boots to what is already on the board and never looks at the tf drive. Any suggestions?

Hi, first, you do a amazing job here I think you help a loooot of people with your videos. But maybe you can help me I cant find any solution on internet. I have a SKR 1.3 which worked perfectly the first day, And today it stop to work without i made any change... I cant access it via USB, when i upload manually the firmware on a microSD card as you shown here the board dont install the new firmware, it stay in the micro SD card... Do you know this issue ? I know you are not the bigtreetech support but maybe have you an idea ! Have a nice day and keep up your fabulous work.

what is platform io on atom?

Great video! I was able to get firmwar.cur on SD card after booting the SKR. I've tried 2 computers (1 laptop, 1 desktop). Both can see the SD card, but, Pronterface won't connect using either computer. Also tried (2) skr v1.3 boards, 1 installed on printer, the other just out of the box. SD cards are the ones that shipped with thr SKR's. Any suggestions?

I followed your tutorial on how to load this via usb and thought I did it. When I unplugged the usb and plugged it back in to check if the .bin file was gone, windows no longer recognized the usb device and pronterface couldn't connect. Now I'm trying to load the firmware this way and when I click compile I get this error message: 'platformio' is not recognized as an internal or external command, operable program or batch file. Unable to execute: platformio Make sure cmd:'platformio' and cwd:'C:\Users\Brian\Desktop\BIGTREETECH-SKR-V1.3-master\firmware\Marlin-bugfix-2.0.x' exists and have correct access permissions. Binaries are found in these folders: C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\WINDOWS\System32\WindowsPowerShell\v1.0\;C:\WINDOWS\System32\OpenSSH\;C:\Program Files (x86)\Intel\Intel(R ) Management Engine Components\DAL;C:\Program Files\Intel\Intel(R) Management Engine Components\DAL;C:\Program Files\LLVM\bin;C:\Program Files\Git\cmd;C:\Users\Brian\AppData\Local\Microsoft\WindowsApps; C:\Users\Brian\AppData\Local\atom\bin;C:\Users\Brian\AppData\Local\Microsoft\WindowsApps;;C:\Users\Brian\AppData\Local\Programs\Microsoft VS Code\bin Have any ideas?

Hi, Your videos are the best out there! I'm new to upgrading... have an ender 4. Got the skr v1.4 turbo, tmc2209, bltouch and tft35... and not having much luck upgrading. I've followed your other videos on the 1.4 and turbo, but couldn't get Y or X right. And now the usb is not recognized. Not sure what happened, but my search brought me to this video. Atom won't install right on my computer, so can I use Vscode instead of Atom to follow along with video? Thanks

I followed all the steps and cant get it to work I still see 2 files when I plug in the board not just the .cur file can anyone help me please

Hi, I followed along the whole vid, but at the very end, the two files remained. It compiled successfully, went right in every way (followed other videos and tutorials also), but i got the same result with all of them. The two files remained, or the bin did not convert to .cur. How is that possible? What could I do now? TIA

Some one can help me? I cant upload the firmware even when i use this method, I think I have problems with the bootloader...

.cur for current ... ? not cusor ;)

Sorry Ed. I wasworking between 2 google accts. See my latest reply under Linda F.