Snowmobile Top End Rebuild

Рет қаралды 46,145

4 жыл бұрын

Пікірлер: 47

@Tyaug 8 ай бұрын

Thanks for the video I don’t have my dad around sadly he passed away 5 months ago and he would show me what to do so I am going to fix up my skidoo tomorrow by my self

@TopoPilot 2 жыл бұрын

Thanks for being so helpful to the sledding community with your post. Says a lot about you as a mechanic. Best wishes.

@benrichardson8314 3 жыл бұрын

Going to rebuild my Indy 500 soon, this video helped me a crap ton! Thanks guys!

@tmmmm9341 2 жыл бұрын

Pro tip check ring gap in cylimder firts by running the ring threw the cylinder with a feeler gauge to make sure gap is within factory spec

@KCreations4You 2 жыл бұрын

I wish I could find a video on this.

@wadewacker7276 2 жыл бұрын

Wouldn’t mind seeing a video on how to drain/fill antifreeze from the engine before and after rebuild 🤔👍

@genuinbud3887 4 жыл бұрын

great video, thanks for posting!

@keving.4020 3 жыл бұрын

Dont forget when installing those circlips that the notch HAS to be at 12 or 6 position due to the inertia of the up and down stroke. Could pop out if not and result in catastrophic engine failure and damage.

@darksilencegaming7749 Жыл бұрын

Wait wdym 12 or 6

@grusminions7652 Жыл бұрын

@@darksilencegaming7749 think of a clock. 12 o’clock is straight up. 6 is straight down

@chaley9093 Жыл бұрын

circlips makes no difference on location. They have to be totally seated.

@ryanbenbow-zx2sd 9 ай бұрын

@@chaley9093you're right. But.the ristpin does. I rebuilt a 570 motor. It is running good. I Have everything On it is ready

@sethmabrey8290 2 жыл бұрын

I'm 16 and a rebuild is needed soon for my exciter 570 this helped give me an idea of what to do thanks

@johncollett4621 Жыл бұрын

great job guys.....u explained everything good....

@danofalltrades3567 Жыл бұрын

Thank you!

@wadewacker7276 2 жыл бұрын

Excellent video gentlemen👍

@kennethallison2168 2 жыл бұрын

not bad but i never run my tourqe right up to 20ft lbs first shot tourqe half way and then up to final tourqe spec. but nice job

@stynger007 6 ай бұрын

If you rotate the head to get the piston in is there a chance you are moving the piston ring to cancel the hole opening on the piston?

@trippmccoy2328 4 жыл бұрын

great video

@scottwidrick1835 6 ай бұрын

just what i needed Thanks

@francismcknight9750 3 жыл бұрын

yeah good job but i cant really repair the top until i have the engine the track the track rail or guide

@Pack_the_Ripper 3 жыл бұрын

Hey I am in the process of installing a 580 in this same chassis

@kckuc310 3 жыл бұрын

Excellent

@robwells5753 3 жыл бұрын

Good vid im glad you ain't painting the engine orange

@alaskacal9246 3 жыл бұрын

Thanks

@dilln3117 2 жыл бұрын

Thanks guys this video is awesome

@chaley9093 Жыл бұрын

"PIP Mark" for the top of the ring. It is usually a dot. Make SURE that the spiral circlip is all the way seated. Oh so the second cylinder has to be done properly?😂 The 1st one doesn't matter.

@KyMcFarlane 10 ай бұрын

Is It easier to rebuild the top end with the motor still in the sled? I’ve got a 2003 Firecat 500 and I’m trying to decide whether to pull the motor or not for top end rebuild

@danofalltrades3567 10 ай бұрын

It’s very possible in the sled and less wrenching.

@Steven-hi3pk Жыл бұрын

I have a 2009 arctic cat m6, what all should I replace when I rebuild the top end?

@danofalltrades3567 Жыл бұрын

Top end usually consists of piston, rings, circlips, pin and bearing.

@Steven-hi3pk Жыл бұрын

@@danofalltrades3567 ok, thanks

@Afflicted-vh9ox 3 жыл бұрын

Anyone know of i video of getting the piston off? I got one c clip from the piston still wont come off... 95 arctic cat 580 ext

@danofalltrades3567 3 жыл бұрын

Did the top end ever run hot? Wrist pin could be frozen in the piston?

@Afflicted-vh9ox 3 жыл бұрын

@@danofalltrades3567 Yeah I figured it out. I was being too careful about it.. I just heated the piston up with a torch and the wrist pin area then tapped it out with a socket extension with electric tape as kind of protection... anyway Piston changed old sled fired right up... adjusting the piston rings so the cylinder block would fit was a tough with out special tool or w/e haha just used a flat head and my fingers 🤣

@tinytim9453 2 жыл бұрын

I just brought home a free barn find, (basement find actually) the tag looks like it says 1999 but doesn't really look like a 99. It's a Jag 440 Deluxe and the engine is seized. Gonna try dumping some oil in the heads. What could the reasons be why it's seized? Moisture in the basement or? What does AFS on the hood mean?

@garr421 2 жыл бұрын

Could be from sitting or could have seized while riding. Could be why it was parked. Moisture could have gotten in if carbs were never drained or plugged. If the spark plugs were out, for sure moisture got in.

@salraso1389 2 жыл бұрын

What kind of piston was used for this install?

@danofalltrades3567 2 жыл бұрын

Don’t remember? The customer brought me all the parts

@danmartin4043 Жыл бұрын

Pro x

@RobertSpencer-zw1cl Жыл бұрын

on my f7 the marks on pistons face to the front of sled ?

@danofalltrades3567 Жыл бұрын

Most of the time the arrow on top of the piston point to the exhaust (most)

@danielsmith8283 2 жыл бұрын

Does it matter what ring goes on top and bottom?

@danofalltrades3567 2 жыл бұрын

Yes! Should be marked with a T or say top

@devinporter5002 2 жыл бұрын

There's gaskets in mine not o rings

@chadbreton4951 8 ай бұрын

You are advising people to use petroleum jelly on rubber O-rings! I suggest you do a little bit of research about that. You will find that it eats away at the rubber. Viewers, this is why you should thoroughly review the repair manual for your machine first and foremost before searching KZfaq because KZfaqrs are not necessarily experienced mechanics

@danofalltrades3567 8 ай бұрын

This is coming from a guy that has 1 subscriber and no videos. No one made you watch my video. By all means if you have a better technique, make a video and show people. Instead of beating someone down who is trying to help! (Btw this machine is still running.)