No video
Spicer 18 Jeep transfer case rebuild
Рет қаралды 5,881
Күн бұрынThis video is sponsored by Kaiser Willys Auto Supply
Use code REDEYEGARAGE10 to save 10% of your entire order from www.kaiserwill... they have tons of Willys and AMC parts!
If your jeep transfer case needs rebuilt or resealed, or you just want to see how things work you’re in the right place. Let’s dig in! The spicer 18 variant was used in all Willy 4x4’s from 1941-1972(early) before being replaced by the Dana 20. The spicer 18 transfer case is a cast iron 2-speed gear drive unit. The most common low range ratio is 2.46:1 (civilian) it has a offset rear output with passenger side drop. It is extremely robust/small/light…it can handle lots of power and it’s very easy to work on! Please feel free to ask questions! Thank you for watching!
Dissassembly: • Rebuild a Willys jeep ...
Parts used in this video:
Overhaul kit: www.kaiserwill...
Rear Flange: www.kaiserwill...
Front yoke: www.kaiserwill...
Yellow metal safe gear oil: www.kaiserwill...
⭐️ Service manual: www.kaiserwill...
#willysjeeps
@randallstewart8487 6 ай бұрын
Good video on the T-18,allready done my 48 2A Trans/Transfer Case,ready to go back in,getting all the parts together now for my T-90 D-18 for my 56 Kaiser Willys Truck!Thank You for taking the time to make and post this video,very help full to all!
@redeyecafegarage7484 6 ай бұрын
Thank you! 🙏
@TheToolmanTim 2 ай бұрын
Excellent video. You did a great job explaining the hows and whys of each step. I tuned in because after installing new seals I've had a couple problems with leaks. Your video gave me the answers I needed. Thanks so much! Subscribing now.
@redeyecafegarage7484 2 ай бұрын
Awesome, thank you! I’m glad it was helpful! 👍
@greywolfwalking6359 6 ай бұрын
Good "how- to" on this one..awesome job!! Thanks teach!! 🤙🧙♂️🐺👍
@redeyecafegarage7484 6 ай бұрын
Thank you hombre!
@KaiserWillysJeep 6 ай бұрын
Great video! Thanks for sharing!
@user-wz2ze3tl7x 3 ай бұрын
Awesome teaching video.
@redeyecafegarage7484 3 ай бұрын
Thank you!
@unpob 2 ай бұрын
Very helpful thank you
@ciscokidfab7595 5 ай бұрын
Very thorough. Thank you for taking the mystery out of the magic.
@user-br8un5xq7i 6 ай бұрын
That's a lot of experience of the yrs we love do do what we do take care dad be careful
@redeyecafegarage7484 6 ай бұрын
😃 You know it! 👍 thanks for watching!
@user-br8un5xq7i 6 ай бұрын
Thank you
@frederickdominguez4829 28 күн бұрын
Awesome clip. 32 ugga duggas I set mine up at too.
@tr4x4 5 ай бұрын
Shims, on the speedometer housing, I have a 1960's Brazilian service from Willys Overland, was setting with a filler gauge between the high gear and the main shaft...
@redeyecafegarage7484 5 ай бұрын
I have no idea what you’re talking about. lol… the procedure used in this video for setting output end play is the correct method.
@pierrehuard1341 6 ай бұрын
Good use of copper spray sealant 👍...Is rebuild minor kit from KW a Crown kit? Never seen that type of shaft before
@redeyecafegarage7484 6 ай бұрын
No, this is a kit they assemble themselves. They’ve been working hard to put together the best kit possible.
@pierrehuard1341 6 ай бұрын
Good to know they're trying to up their game 👍@@redeyecafegarage7484
@lonewolverinesurvivor6303 Ай бұрын
So of them uses cage bearings instead of needle bearings.
@redeyecafegarage7484 Ай бұрын
Roller bearings on the outputs. Needle bearing a on the intermediate shaft 👍
@lonewolverinesurvivor6303 Ай бұрын
My intermediate shaft is 3/4 inches and uses cage bearings with the intermediate gear.
@lonewolverinesurvivor6303 Ай бұрын
@@redeyecafegarage7484 you can use needle bearings but I like to use the the cage bearings instead.
Red Eye Cafe Garage
Рет қаралды 2,2 М.
Pine Hollow Auto Diagnostics
Рет қаралды 50 М.
Fabiosa Best Lifehacks
Рет қаралды 27 МЛН