Stage6 R/T Variator Installation || Piaggio Zip AC to LC
Рет қаралды 101,825
6 жыл бұрынWith this variator throttle response have been a lot quicker than the stock, especially when you ride with ~50kph and you open the throttle.
I have a mix of rollers 3x6.5g 3x8g to rev ~8200rpm
I think the fuel consumption have been raised.
Instagram Page: / binos_tuning
Αν θέλετε να αγοράσετε μια τάπα για τη μίζα, στείλτε μου μήνυμα στο λογαριασμό μου στο instagram @binos_tuning binos_tuning?ig...
ή κάντε κλικ στο link
www.ebay.com/itm/314870015674
• My First 3D Printed Pa...
If you want to buy a starter motor plug, message me on my instagram account @binos_tuning binos_tuning?ig...
or click this link
www.ebay.com/itm/314870015674
• My First 3D Printed Pa...
@jmcci2069 4 жыл бұрын
Excellent Job 👍👍
@oscarharrison9100 3 жыл бұрын
very useful video, thank you!
@trentroger9923 2 жыл бұрын
Instablaster...
@zoekaran 6 жыл бұрын
eutixos uparrxoun kai tetoioi youtubers kai ksefeugoume apo tin routina tou beauty kai tou katanalotismou! evge
@tarace9997 Жыл бұрын
C’est quoi la petite rondelle que tu a mis avant de remontée le vario ,j’en est aussi un avec mon multivart mais je pensais que c’était une bague de bride ?
@MrBerenguer67 2 жыл бұрын
Hi Thks for your excellent video whitch pressure the Waite spring on malossi kit thank you
@binostuning 2 жыл бұрын
This is not a mallossi kit
@MrBerenguer67 3 жыл бұрын
Thank you for your video whitch size rollers you put in also whitch speed you get thks
@binostuning 3 жыл бұрын
I'm using 5.8gr rollers for stage6 streetrace with primary gear kit for more speed. Revving to 11K rpm and top speed ~130kmh
@youtubenutzer6236 Жыл бұрын
Does the Malossi belt your using now goes up to the highest point of the rear pulley? Im searching for a belt that is longer like the original so I can use the full 134mm (Same like oversized kit) of the rear pulley diameter. My vario ist big enough for a longer belt but I don’t know the perfekt length
@binostuning Жыл бұрын
I don't know if it goes all the way up on the pulley, I haven't measured it. But if your looking for a longer belt, search at maxiscoot or get an oversized one that matches your preferred length.
@MrBerenguer67 3 жыл бұрын
Hi mate thks four your video i have a Piaggio Zip 50 2t when i drive and give a full throtle the speed cut down i cleaning the caburettor and i change the spark plag and still the same this happen to you thks
@binostuning 3 жыл бұрын
Thank you! Check your fuel lines that go to your carb, check the jets or look for air leaks at your intake or crackshaft seals.
@ants4193 7 ай бұрын
when you switched your belt from the standard piaggio one to the malossi one was there a big improvement? and is it okay to use this variator with the standard belt?
@binostuning 7 ай бұрын
I think I didn't see any improvement other than the better longevity. Yes it's ok to use the standard belt with this variator, unless you have the complete overange kit installed.
@rokpavlic2575 3 жыл бұрын
When im putting the variator in and then the pulley gets in a bit hard and when i try to electric start it .. it makes crunching noises and its not suiting so what do i do?
@binostuning 3 жыл бұрын
something is not fit properly or the teeth of the starter motor are worn
@kyledavies3101 6 жыл бұрын
Could you show us a video of the bike running?
@binostuning 6 жыл бұрын
Extract yes I will film a video today Tomorrow it will be on KZfaq
@yilberthgomez3438 3 жыл бұрын
@@binostuning g
@user-zm3uz7bg1d 2 жыл бұрын
Hi, what variator belt size did you use with this RT variator?
@binostuning 2 жыл бұрын
I was using the standard Piaggio belt but now I'm using a mallossi one, I don't remember the size.
@user-zm3uz7bg1d 2 жыл бұрын
@@binostuning thanks for help)
@scottgehlken2330 Жыл бұрын
where do i get these parts
@binostuning Жыл бұрын
maxiscoot.com
@jasonjod1ail 4 жыл бұрын
Hey ik this video is old but what main jet are you running
@binostuning 4 жыл бұрын
On 17.5mm dellorto I am using 78-82 main jet
@sunnybeachweddings7037 3 жыл бұрын
How many grams are your rollers?
@binostuning 3 жыл бұрын
With my current set up is around 5.5gr
@R_T_Remko 4 жыл бұрын
Why you put the bigspring upside down??? Its not good metal on letal in clutch.. ( sorry for bad english)
@binostuning 4 жыл бұрын
Yes this is true. Is wrong to put it this way. The correct way is the opposite but I don't have it in the video.
@R_T_Remko 4 жыл бұрын
@@binostuning you switched it I hope haha
@binostuning 4 жыл бұрын
@@R_T_Remko yes I did. Also the stock black spring fits better for my setup.
@R_T_Remko 4 жыл бұрын
@@binostuning what is your setup?
@binostuning 4 жыл бұрын
@@R_T_Remko Now I'm running stage6 Street race cylinder just with port matching, yasuni c16 pipe, stage6 R/T variator, stock belt, stage6 sport clutch, mallossi clutch bell, pwk 26, stage6 reeds valves and block, polini primary gears, electric water pump. Probably 10-12hp
@loca4159 3 жыл бұрын
How mutch gram rollers comes with it?
@binostuning 3 жыл бұрын
6 x 3.5 gr
@loca4159 3 жыл бұрын
Thanks :)
@gonijahja1506 2 жыл бұрын
Hello man i liked this video so much and im looking to do this to my piaggio nrg and i wanted to ask whats the speed before and after the kit ?
@binostuning 2 жыл бұрын
The top speed is the same, but changed the way it accelerates.
@rihardsindars3762 2 жыл бұрын
@@binostuning is the acceleration way faster?
@binostuning 2 жыл бұрын
@@rihardsindars3762 yes of course
@rihardsindars3762 2 жыл бұрын
@@binostuning thanks
@itc-0076 Жыл бұрын
So... the is no electrique starter ?
@matis_5828 2 жыл бұрын
Hi can you tell me what is the weight you put in your variator plz
@binostuning 2 жыл бұрын
They are 5.8gr
@matis_5828 2 жыл бұрын
@@binostuning set up ?
@binostuning 2 жыл бұрын
@@matis_5828 you can watch my latest videos
@hakont.4960 4 жыл бұрын
Dude, never tighten nuts with an impact driver, unless you actually limited it's torque somehow.
@binostuning 4 жыл бұрын
My impact have a torque choice.
@hakont.4960 4 жыл бұрын
@@binostuning Ah, should work well then.
@deurlii7920 3 жыл бұрын
Those bolts secure parts spinning upwards of 15000rpm, trust me you want those tight tight.
@0bDaily 3 жыл бұрын
You put the clutch spring back on the wrong way👀🥴
@binostuning 3 жыл бұрын
Yes I realised that soon after.
@0bDaily 3 жыл бұрын
@@binostuning no worries just thought I’d let you know pal 🤙👍
@mohammedkarim8349 3 жыл бұрын
How is That indicated
SupereFix
Рет қаралды 312 М.
Zandri Shop
Рет қаралды 109 М.
Samodel
Рет қаралды 467 М.
Scooter Street
Рет қаралды 89 М.
Roud Offthegun
Рет қаралды 1,3 МЛН