Standing Seam Metal Roofing: How To Install Transition Trim

Standing Seam Metal Roofing: How To Install Transition Trim - High To Low

Рет қаралды 18,167

Күн бұрын

Discover how to install transition trim on a standing seam metal roof. Step by step standing seam metal roofing installation instructions that explain all of the steps. After you watch this video you will be able to install transition flashing like a pro.
00:00 How to install transition trim on a standing seam metal roof
00:59 How to layout transition flashing on a standing seam metal roof installation
02:00 How to install z bar for transition trim
04:18 Mastic tape installation for standing seam roofing
06:00 How to fasten z closure for transition flashing
07:23 Silicone and mastic tape installation at zee closures
09:01 How to fasten transition flashing for standing seam roofing
10:10 Joggle cleat installation at the transition of a metal roof
If you already have not purchased your standing seam metal roof, give us a chance to bid your job. Save 15% to 50% with our manufacturer direct pricing and great customer service. Inexpensive delivery anywhere within the United States.
Visit Our WEBSITE
bit.ly/wsmr-website
Standing Seam Metal Roofing Installation Video Series
www.westernstatesmetalroofing...
Transition Trim Detail - High To Low
www.westernstatesmetalroofing...
How To Install Transition Trim For A Standing Seam Metal Roof
1. Take the transition trim and set it on top of the high of the panels NOTE: Make sure it flushes out and stays on the same plane as your lower pitch.
2. Mark the actual high of the standing seam panels so you know where to place your mastic tape.
3. Install Z trim, mastic tape, and silicone sealant
4. Fasten the transition flashing with pancake head screws
FOLLOW US ON SOCIAL MEDIA:
FACEBOOK: bit.ly/facebook-wsmr
INSTAGRAM: bit.ly/instagram-wsmr
TWITTER: bit.ly/twitter-wsmr
LINKEDIN: bit.ly/linkinin-wsmr
HOUZZ: bit.ly/houzz-wsmr
PINTEREST: bit.ly/pinterest-wsmr
KZfaq: bit.ly/youtube-wsmr
Visit our LEARNING CENTER
bit.ly/learning-center-wsmr

Пікірлер: 10

@walterdavis3638 7 ай бұрын

I love the idea of a learning channel, however, in this video, the young man has skipped over some of the very important details, ie: the z trim fitting is skipped, explanation of the purpose of each step, close up shots of the individual components, removing the tape properly from the mastic, making sure your fasteners are perpendicular to the surface, etc. A seasoned installer would have a lot to say while watching this demo. There is a great shortage of good content in metal roofing vedios and I hope to follow more of your offerings. Thank you for putting this out there.

@Rob-lv7wo 2 жыл бұрын

Any chance you have a video of metal to shingle roof transition? I plan on putting a covered deck roof but its going to be a 3 12 pitch so going to use metal on it. The house is shingled with a 12 12 pitch and all the videos are metal to metal transition.

@osueathenscountyag 2 жыл бұрын

Is there a rule f thumb on how long the upper panel will actually need to be from the pitch break to the the ridge in order to order the correct length panels or are these just going to have to be ordered long and cut to length?

@Bayouboy5617 2 жыл бұрын

Do you have a video on how to properly nail the shingles overlapping the transition metal? Thanks

@WesternStatesMetalRoofing 2 жыл бұрын

I do not. Thank you for commenting.

@Bayouboy5617 2 жыл бұрын

@@WesternStatesMetalRoofing no problem love the video's.

@davidchristensen1219 11 ай бұрын

Question for all the experts: I have a pitch elevation transition to install where the transition doesn't span the width of the side of the roof. To make matters worse, the upper corners of the lower transition meet a hip ridge, so the ridge cap will actually overlap those corners of the transition. The building has a 4 sided hip roof (no gables) and the transition is for the front porch, where the front porch does not extend the full length of the main roof and it attaches ~2ft up the roof. So I'm trying to figure out how to transition from porch roof to main roof (those upper corners of porch) and how to plan for the hip ridge caps to be continuous.

@barrykozak3536 9 ай бұрын

I'm kinda in the same boat as you. trying to figure out how I'm properly going to get this done.

@arayahomes4308 Жыл бұрын

Great video! The install on that roof barrier is absolute CRAP, look at the wrinkles and folds in that. For such a high end channel showing great installation advice, I don't know why you'd have a barrier install like that in your demo mockup. Terrible.

@daniellewis984 Жыл бұрын

Your Z-trim stage both looks terrible and is. It functions as a dam, and if water gets in there it will be trapped there, creating a pool. You actually want water to be able to slip out underneath the Z-trim onto the roof, not being waterproof, but being bug-proof. It's actually worse than simply guiding the water down into the house if it gets there by folding the sheet ends up to form the Z similar to what's done at the bottom of sheet, and assume that the transition trim fulfills the role of redirecting everything out and over.