Steel Hardening Techniques & How to Make a Square Hole for Lathe Chuck Thread

Рет қаралды 75,673

8 ай бұрын

#lathe #machining #creative
Steel Hardening Techniques & How to Make a Square Hole for Lathe Chuck Thread
I use this combination technique to make a square hole to use for the lathe chuck key.This square thread turning is for a 16 inch lathe chuck that broke due to too much force when clamping the workpiece And for this steel hardening technique, I use salt water as a cooling medium
Lathe
Lathe techniques
Creative idea
Making tools
Making gear
Create a double square thread
Welding
Thank you for visiting, don't forget to like and subscribe for support, thank you

Пікірлер: 35

@Wowmechanics1 7 ай бұрын

Mechanical Expertise Revealed

@raydavincci2912 4 ай бұрын

O material para ser temperado tem que ter pelo menos 0,45% de carbono, caso contrário terá que ser endurecido pelo processo de cimentação que pode ser com cianeto de potássio.

@ngoanvu1583 7 ай бұрын

Gia nhiệt kiểu này ko ổn...sau này giòn dễ bị gẫy sau nghuy hiểm khi cặp phôi gia công

@tornerongkamayvlog1009 7 ай бұрын

Chuck screw good job

@KULITEKNIK001 7 ай бұрын

Thank you

@user-tn6nz2vn1t 8 ай бұрын

keren euy

@howardosborne8647 7 ай бұрын

Good job👌 Is that a square thread form? That is a lot less expensive than buying a new screw from Pratt Burnerd

@sararavan 6 ай бұрын

Chuck spindle left hand threading you show right hand

@Jmastffp 7 ай бұрын

Your ingenuity is impressive. Excellent work sir

@KULITEKNIK001 7 ай бұрын

Thank you friend

@user-bt1cg1re5e 8 ай бұрын

Отлично 👍

@KULITEKNIK001 8 ай бұрын

Thanks

@bullboss7698 6 ай бұрын

They know how to get it done. Assembling the chuck in the dirt is hard to watch.

@ARIFINLATHE 8 ай бұрын

❤

@MartinArielPadilla 7 ай бұрын

muy bueno

@KULITEKNIK001 7 ай бұрын

Obrigado amigo

@yeagerxp 8 ай бұрын

Good job 👍👍👍Thank you for sharing. Be safe 🇨🇦

@KULITEKNIK001 8 ай бұрын

Thank you 👍

@danielsolaro952 7 ай бұрын

Hola, minuto 2:58, la pieza que estás construyendo aparece cubierta por una capa blanca, qué le hiciste? Cómo lo hiciste?

@KULITEKNIK001 7 ай бұрын

Aquí lo llamamos solución UYAH como medio endurecedor.

@rusticagenerica 8 ай бұрын

Pourquoi ne pas porter des gants?

@aztron 8 ай бұрын

Besi bagia ujung lobang kotak setelah dipanaskan di celupin ke bahan apa itu bang yg putih mengeras

@KULITEKNIK001 8 ай бұрын

Air garam bang

@aztron 8 ай бұрын

@@KULITEKNIK001 kok jadi keras kaya tepung cryspi

@bambangirawan6011 8 ай бұрын

Pakai bahan VCN ya mas terimakasih 🙏

@KULITEKNIK001 8 ай бұрын

Iya bang

@nadersayed3276 8 ай бұрын

What mean VCN ?

@KULITEKNIK001 8 ай бұрын

@@nadersayed3276 VCN is a high strength low alloy steel (HSLA steel) product produced by Bohler, which is equivalent to the European standard EN 25 or the German DIN 34cr. Meanwhile, there are differences

@nadersayed3276 8 ай бұрын

@@KULITEKNIK001 thanks

@mesincacahkaryacipta8408 8 ай бұрын

Besi as nya pake st berapa om?

@KULITEKNIK001 8 ай бұрын

Pakek vcn bagus,atau as roda truk

@mesincacahkaryacipta8408 8 ай бұрын

@@KULITEKNIK001 siap om

@user-fe4hz2vr9y 7 ай бұрын

Почему вы предпочитаете 4х кулачковые патроны, а не самоцентрирующие 3х кулачковыме ?как партию шлифованный заготовок зажать, или одну деталь перевернуть !, это же ад! Мне 4х кулачковый патрон ни разу не понадобился.

@jerrypeal653 7 ай бұрын

Didn’t look concentric

@howardosborne8647 7 ай бұрын

It must be concentric or the jaw wouldn't screw in like it did. I think it more likely it was set in the jaws a little bit skewed when he turned it around to clean it up with abrasive paper.