Very well explained first time i have come across such a simple explanation.

Excellent presentation on how to use both types of loaders. It helped me quickly get the STM32F103C functional using the Arduino IDE. Thank you and thank you again. Respectfully, Steve

Just one word help me to go with Bluepill without errors is "Most of the BluePill comes with 128kb Flash"...! Very helpful!

Thank you so much for this tutorial!!! I had been trying to get this to work for ages then I watched this video and I was done within minutes.

Great job Saravanan, thanks! Trying to get my bluepill going in August 2019, I wondered which of the links I researched had the most current info. This one turned to work quite well. I'm using ST-LINK, so I started in that part of the video, but I also needed to go to the serial portion on how to add the board to the board manager in the Arduino IDE. The URL gets truncated on my system for some reason but I was able to copy it from the video. The other thing I had to do was get the driver, which worked fine per instructions. One slight glitch was that it didn't show up in my Device Manager. But I went ahead and after all was done, it does show. So apparently it became visible after the IDE started using it. I guess. After those two downloads and then following the step-by-step in the video for wiring connections and IDE options I was good to go. Note that the "blink" sketch in Examples is Read Only to you have to move it to your sketchbook to add the #define line. I've never been so pleased to see an LED blinking on and off at a 1 second rate. -- Nick

Thank you for sharing your time and effort!!!

Nicely done, sir. Easy to follow and your blog is so detailed and well explained. Thank you.

Thank you so much! Exactly what I needed to get started.

Thank you so much sir for this video...helped me a lot...looking forward to see more of these videos

thank u very much - this tutorial is simple and helpful

THANKU SIR THANKU SO MUCH

Good video, but the ST-LINK wire connection was explained incorrectly. Please correct the video. I hope people who watch this video also check and use the ST-LINK connection.

Hello sir! I need your help i am getting an error. Sir please help me🙏🏻🙏🏻

Very nice job 😊

Great job

Nicely explained, I am kind designing my own pcb. I have same doubt. If I use the STLINK method then I don't have to Expose the BOOT pin with jumper arrangement is that correct. However via UART Pins I have to expose the BOOT and RESET Pin both

I have downloaded STM32 Cube IDE and bought USB to TTL. How can I upload program using it ?

Very informative and useful

Thanks a lot, I had problems with connecting STLINK

Great explaination 👌🏻

Tank you for this lesson, good work works good :-)

Excelentes Sus Videos , muchas Gracias !!!!!!

Hi, I am getting the following message, any suggestions? 'C:\Users\Mike's' is not recognized as an internal or external command, operable program or batch file. Failed uploading: uploading error: exit status 1

for my example my arduino compiler doesnt write in read like in minute 09:00 and so my PC13 doesn't blink what can the problem be? btw it says transfer complited even tho my cart isn't connected

Nice work helped a lot Thank You : - ))

can you make tutorial sending/receive data via bluetooth using stm32

Why do I have to unplug the ST LINK Device whenever update the program? (STM32F103CB + KEILV5 + ST LINK V2)

Great tutorial

Çok Teşekkür ederim. Thank you so much. :D

Sir I am trying to program STM8S103 Board, but not succeed, I followed many tutorial but no solution, can you Please guide me, It will be very helpful for me because I am trying to solve this problem from 1 month

Sir mujhe gsm module, arduino uno nd relay module Se light vagrh control krna h iske liye code bna dijiye sir plz

are you have any example for tft 8 bit with plue pill and thank you

Thanks for uploading

Hi , I have Arduino Nano Stm32. Which has already program in it. I want to copy program from Arduino board.

sir can u show how to use internal rtc using arduino ide

Please make a video on STM32 Cube IDE

Wirtual port installed 3 times not successful in window 7 32 bit single user. Any help, please!!

I have the Blue Pill card. It has an MCU STM32F103C8T6. The problem is that the jumper for the BOOT 0 when it is at high (1) the led pc13 always lameps ! It does not enter programming mode. And I can't program the card via FTDI. I tried with ST LINK V2 and it works with the reset pin cable (RST). Because not having boot 0 working I can't keep it reset. The problem I program with the ST LINK module I can not use serials. I'm initialing Serial 1 (Serial.begin(115200)) but when I use the print statement it doesn't appear if I connect an FTDI module. ST LINK to program FTDI to display the serial but does not work. Is there a way to activate the BOOT 0 jumper in such a way that when the set to one (HIGH) he after the reset remains in programming mode ?

Thank You for help! :D

good presentation

Thanks you vert much 🤗

I found problem with stlink "arm-none-eabi-g++: error: CreateProcess: No such file or directory exit status 1 Error compiling for board Generic STM32F103C series. " I don't know what happen and how fix it?

hi sir how can import hex file from stm32f103c8t6 microcontroller

Thank you!

If we use keil version is that possible

At the IDE Arduino I can't see the PORT, and I don't have the "Ports (COM & LPT)" option at the Device Manager, thanks

Why do you say chose 128k flash in the video but use the 64k option? And how do you remove the program from the stm32?

sir i have a question..........any code for serial usart receiver interrupt

Your video is really informative although the video quality is very poor. please try to upload contents with better video quality in the near future

Thank you

Sir, I'm following instruction on the video, I get Done uploading status, but my PC13 Led not blinking I got orange mssg STM32 flash 0,4 Failed to init device. STM32flash, google code.com/ using parser : raw BINARY Interface serial_w32 : 115200 8E1 any sulotion for my led blinking, sir? Thank You

Thanks

'pc13' was not declared in this scope, this message on compile

thanks

Sir, can the st-link be used to get the Serial logs on the console while running the program.

Sir in my pc windows 10 home this error coming how to solve that (stm32flash 0.4 /=\: No such file or directory Intel HEX ERROR: System Error stm32flash.googlecode.com/)

Thanks for demo. Still unclear about stm-32, debugging. Can I only use this for program upload? Is there no way to get a com-port output, or use this with visual studio to monitor variables and pins?

Failed to init device. stm32flash 0.4 stm32flash.googlecode.com/ Using Parser : Raw BINARY Interface serial_w32: 115200 8E1