Stonesetting: Flush Setting 3 Ways

Stonesetting: Flush Setting 3 Ways - Part 2

Рет қаралды 11,415

Күн бұрын

In this video, I discuss creating a flush/rub-over setting using a setting bur. I cover how to burnish your setting, how to know when your stone it deep enough, and what burs to use. I also discuss troubleshooting and the use and care of the different burs used with this type of setting. This video is also the setup for Flush Setting 3 ways - Part 3, which covers flush/rub-over settings with the hart & ball burs. Please see Part 1 first as a lot of the basics like layout, measuring your stones, metal thickness, uses, etc. are covered.
Part One: • Stonesetting: Flush S...
Part Three: • Stonesetting: Flush S...
Flat Square Edges on Metal video: • Flat Square Edges on S...
Many of the tools and materials are the same in all of these videos. Check out Part One for a complete list! • Stonesetting: Flush S...
Ran out of room on part one's, video details page! So, posting this one here. This is great for a quick change handpieces and using larger bits:
Collett Adapter aka Twist drill adapter - Otto Frei: Part # 128.216.
Amazon: haven't tried them so, I don't know how they are. Here's a link: amzn.to/3KzpDSv.
My website: Metalsmithing from A to Z, Nancy.LT.Hamilton.com is LIVE and KICKIN'!
My store is open for business!!! NancyLTHamiltonShop.com
Pinterest: / nancylthamilton
Facebook: / nancylthamiltonjewelry
Instagram: @nancy.lt.hamilton
Thank you for watching! If you enjoyed this video, please consider "liking" and of course, subscribing. Don't forget to allow notifications or you'll never know when the next video will be out!
Quick links to video chapters
0:13 Introduction
0:56 The setting bur: layout and divoting
2:10 Drilling the first hole
3:03 Ideas for cleaning burs
3:28 Ball bur VS. a drill bit
3:58 Ball bur
4:15 The bud bur
5:27 The setting bur
8:28 Burnishing
12:35 Troubleshooting
15:16 That's it! Summary
This page may have an affiliate link or two (or 20! ha!).

Пікірлер: 34

@leighmcqueen1403 2 ай бұрын

Super informative Nancy. Clear, precise and encouraging. Thank you ✅

@koraytas5466 2 жыл бұрын

hello nancy. I'm Koray from Turkey. I turned 47 years old and I am a Jewelry Design Faculty Undergraduate student. There are not many in Turkey that make educational videos like you do. You guys are great. I've watched half of your videos so far and liked them. I do not know english. I am doing this text with google translator. I hope I don't get it wrong. I sincerely thank you from the bottom of my heart. bless your right. Right now, after my family, you are the person I love the most in the world. don't let your hands worry. stay with love and respect. May God give you a long and healthy life.

@NancyHamiltonJewelry 2 жыл бұрын

It all made sense to me! Thank you so much for taking the time to say such kind words!!!! Good luck with your schooling! Hepsi bana mantıklı geldi! Böyle güzel sözler söylemek için zaman ayırdığınız için çok teşekkür ederim!!!! Okul hayatında iyi şanslar!

@catzkeet4860 2 жыл бұрын

Thank you for this. Of all the settings I’ve done, flush setting was always my Waterloo. I had SO much trouble with it, and it was so frustrating with everyone and their poodle saying how “easy” it was to do. I finally managed to get a stone set and realised that my issue was sizing of my holes. All the info on sizing is very helpful cos I STILL have some issues at times

@NancyHamiltonJewelry 2 жыл бұрын

You are not alone! Thank you for writing!!!

@phoebegibbs2181 16 күн бұрын

Thanks so much!

@maryanncauchy2143 2 жыл бұрын

Very helpful-the pictures through the loop were good!

@NancyHamiltonJewelry 2 жыл бұрын

I'm glad it worked for you! Thanks for writing.

@Shukarr Жыл бұрын

Thank you Nancy 🙏

@allanthompson9695 Жыл бұрын

Really useful series for me.Thanks Nancy.

@sasheanones1456 2 жыл бұрын

Good guide!!!

@tlojewelrylove Жыл бұрын

Awesome, thank you so much! 👍😃

@superlace 2 жыл бұрын

This is a great guide. Thanks!

@NancyHamiltonJewelry 2 жыл бұрын

Thank you!

@annh3599 2 жыл бұрын

Thanks Nancy!

@wolfiesown Жыл бұрын

Very nice tutorial, and great to add a troubleshooting section! Thank you!

@Retrosigns1 Жыл бұрын

Thank you, very good videos.

@eanjewellery 2 жыл бұрын

Thanks Nancy 😊

@NancyHamiltonJewelry 2 жыл бұрын

Thank you!

@sylviaprudhomme5417 2 жыл бұрын

Excellent instruction

@NancyHamiltonJewelry 2 жыл бұрын

Thank you!

@pdelmercado 2 жыл бұрын

You look beautiful! That color of lipstick is very flattering on you. Thanks for the tutorial.

@NancyHamiltonJewelry 2 жыл бұрын

Oh thank you! Sometimes miracles occur! Haha

@adiem1653 Ай бұрын

Great videos cheers Nancy I am looking at adding some 1.5mm diamonds to a 1.1mm thickness gold ring i made (making it for the first time) I had a 3mm diamond but it is too deep and sticks out the bottom if the band. Therefore decided on the 1.5mm's as they wont protrude! I drilled a 1.0mm hole in some scrap silver the same thickness as the gold ring and used a 1.5mm setting burr as a test - I can gardly see it. How can i possibly flush set the diamonds as the burnisher is as wide as the hole near enough?

@flambojan_lab 4 ай бұрын

Excellent work, we subscribe your channel

@niradori5046 Жыл бұрын

🙏🙏🙏

@daniellepadgham5165 2 жыл бұрын

Thanks for all the tips and tricks. Maybe the text could be left on a little longer in future😍

@NancyHamiltonJewelry 2 жыл бұрын

I will do that! Thanks.

@JustME-ft4di Жыл бұрын

Thank you so much for your wonderful tutorials. So is it just the tiny metal lip that is holding the stone in place? I have some lively lapis stones that are cylindrical in shape. Flat top and bottom. I would like to put them in a bezel so they sit flush with the top of it. Any idea of the best way to go? I am tempted to cheat and use glue.