So we have Big Clive cooking sausages with high voltage and Diode Gone Wild cooking high voltage modules in the oven. Perfect!

Engineers-meter,liter Diode gone wild-one samsung case

Beautiful water cup. Even plugs into the wall and can heat water directly.

We missed you a lot danyk :)

I admire you had patiency to slowly remove the resin. I definitely wouldn't have it.

Great job in taking the resin apart and back engineering the device internal workings.

1:30 nice water pot

Last time I tried to take apart some resin like this, baking it worked quite well, it became soft AND cracked in many places. I think it depends however. If there is a lot of unreacted chemicals in the resin from the manufacture, this probably works well. I didnt use a normal oven though, instead I used a 400W mercury vapor lamp with the UV protection envelope removed and a reflector. This was heating and irradiating the resin a lot with IR, visible light, lots of UV-B and a bit of UV-C. The wooden table also became black at the surface from all the heat. I always heated it, then peeled off some chunks that became soft, then re-heated and so on, until eventually the last bits were completely dry and hard again. But by that time almost everything was removed. The electronics were relatively undamaged and I was even able to read off some values and the markings on a PCB inside.

Just a quick safety tip: always put the sodium hydroxide in the water, and never the other way around. To understand why, try to visualize in slow motion the first drop of water that would touch the sodium hydroxide, it would be a microscopic quantity of water in contact with a big amount of sodium hydroxide, thus it would be highly concentrated and could react violently. The other way around, the first flake of lye in contact in water would be dissolved in a "massive" quantity of water. My dad decided one day to put the sodium hydroxide flakes directly in the drain and then pour boiling water on it, it made a geyser and his slippers still bear the traces of this experience.

Thank you very much I think you are the only one who can reverse engeniring almost everything Nice work

Great Circuit Diagrams as Allways..

Always Waiting For Your Videos.

This video reminded me in two weeks I'll start my 3rd year in ICT Systems engineering. It might not sound relevant, but we have studied on computer and on paper a lot of circuits similar to the ones you are showing. I'm eager to learn crazier stuff.

Great video, I especially like the explanation of the schematic.

1:28 Using a dissection victim as a water container :)

9.57mins, I wish my cats were that chilled when I'm working on something awkward, always wanting to help and get Right in the way

What a shocking story, I'm a bit stunned by it all.

I was thinking about DOT break fluid for cars. I've had pretty good results on softening all kinds of hardened rubber with it. Might be worth a try.

Sir, very good job

Great video

chant in front of a train station - "lacquer thinner is the winner" 🤣

Nice Vid! I hope your thumb is getting better!

Great to see a new video from you! Do you think you would be able to do a brief 'how it works' video about your memory oscilloscope that uses the TV for its display...it looked really interesting and now I can't find which of your videos I saw you using it!

Do you want to soften the resin or do you want to make it more brittle? I would think if you make it harder but also weaker, then you can easily just break it off with impact soft enough to leave the electronics intact.

You can mesure that résistance with an isolation tester or try to mesure à portion of it and deduce its value., it like the potentiometer found in old tv focus .

4:42 which chemical used in lacker thinner ?

came here to say hello ......being a core electronic engineer i like ur videos

Wondering what could dissolve the potting on some blob IC's. (acid excluded)

Maybe try building a mini-sandblaster such as one made by Nighthawkinlight to blast off the potting compound while being careful to not blast the components inside... :)

Nice video! 👍👍👍 When are the next videos about the Solid State Tesla Coil going to be? Anyway go on like this... Really appreciate 👍💯

8:32 The fire extinguisher seems to have some new features this month

perfect...videos

When a circuit is potted it's not reverse reengineering any more... it's archaeology.

You are the one that no one 🤟

You can try "Chloroform" for dissolve acrylic and resin plastics. Or HCl+Formic acid mixture.

Please, how do we determine the number of turns and the core area?

Wow i have the same lithium battery charger... Waiting for the video 😁😁

Please Can You Explain Why AC voltage Can't be Stored in a Battery.

Can you or someone explain the direction of conventional current flow in the auxiliary winding at 11:26 please. You said the voltage built up supplies even more current to the base of the transistor, via the diode and 24ohm resistor.....so is conventional current flowing from the bottom of the winding, to the top dot, towards the base, out the emitter, and down to the negative rail? It's just confusing because the polarity is marked the same as the primary winding, which made me assume it would be moving from the dot, to the bottom of the winding. Many thanks.

Chemistry with DiodeGoneWild

Ten out of ten for effort mate ;-)

5:33 you have to warm water bath the main container in order to reduce dissolving time .

Please danyk make some dangerous chargers teardown

1:35 you shouldn't mix sodium hydroxide with warm water. The reaction is exothermic and it produces heat when mixed with water. The warning lable says so too.

Drain cleaner would react with aluminum, zinc, magnesium, or silicon...

Please explain AK-1Tufting machine DC motor control

have you thought of doing a timelapse of you drawing schematics?

1:28 a phone charger? Really?

Cat: from where this guy gets horrible smelly stuff.

Req electric flay

I am using a small torch or an halogen lamp to remove about 2 mm each treatment and in 2 hours I am readdy

I waited for this lol 😁

It is the popular tester called avr tester you can find more info on mikrocontroller.net

Using a screwdriver instead of a spoon and usb charger cover instead of a glass thats diode gone wild

Is anyone who can say me what type of transistor is it?

Why no videos coming from this channel??? 😣😣

u speak so nice,it sound like u r singing

Can you please suggest some good books to study all this

Let's put a like of it in it.

12:30 How can current goes from negative then returns to negative?

hmm, what? no counting the coil windings?

You would get circuits without resin on aliexpress

i think your cat was about the worst method of dissection.. the oven seem to be the least destructive!! Loved that video...

1:29 best water pot ever

Hi bro

use acetone to melt plastic

😍

1:28 - Kdybys ji zapojil do zásuvky, tak by se ti krásně ohřála voda 🙂

25sec=50View Niceee 😁

13:48 it's a sparkgap

Man please make a DIY transistor using atmega328p I am really in need of it . FAN FROM INDIA

1:28 poor orico charger :D

USING A CHARGER AS A BOTTLE

Just plug your Samsung water cup in to get hot water :-)

You should just borrow Kreosans Xray machine.... :)

Powerfix from kaufland

موسع بالك

Informative, but also comical....

𝑮𝒐𝒐𝒅 𝒐𝒏𝒆. 𝑰𝒕 𝒊𝒔 𝒊𝒏𝒅𝒆𝒆𝒅 𝒘𝒐𝒓𝒕𝒉 𝒕𝒉𝒆 𝒑𝒂𝒕𝒊𝒆𝒏𝒄𝒆.

интересно а в чешских аптеках есть димексид? )

you poisonous yours self with chimical

SoDiUm HyDrOxiiiiiiiiiide

Deutschland :-)

I want to sub this guy but his accent is 💀 💀💀 idk guys should I sub him ?

you are not good at chemical 🤷🏻‍♂️

First

Audio killed me

Tell me you really dont talk like that in real life right?

Please try to just don't speaking English , it's very better to writing every thing and be quaiet !! I am sure every one know why .