Rebuilding Briggs and Stratton Starter Motor
Рет қаралды 6,268
Күн бұрынIn this video, I'll show how to rebuild a starter motor for a Briggs and Stratton, opposed twin engine. Thanks for watching and be sure to subscribe!
@Z14kt12timandjes1 2 жыл бұрын
Nice work. I work at Briggs & Stratton (27 years now) and this past week I was on a team that disassembled and changed the gear on thousands of these starters.
@stuzman52 2 жыл бұрын
I did have a small chip on one of the teeth for the gear. Thanks Timothy for dropping in and sharing a comment, and be sure to have a great day!
@TheGibby3340 2 жыл бұрын
Nice work. Good for another 20 years 👍
@stuzman52 2 жыл бұрын
Thank you Ian and that's what I'm hoping for 😊 Have a great weekend!
@octaviansorescu7427 2 жыл бұрын
Good job! The best engineer! More video Mr Stuzman!!!!
@stuzman52 2 жыл бұрын
Thank you very much and have a great day!
@rs1971camaro 2 жыл бұрын
With all the upgrades you should be set for awhile! I have an old Murray from the mid 90's that I keep in shape. I like the older units as they don't have as much plastic parts.
@stuzman52 2 жыл бұрын
I agree and hoping to get quite a few more years out of the mower. Have a great weekend!
@SalientDebate Жыл бұрын
Took me 7 minutes to figure out why you sounded so familiar. You have the same accent and tone as Woody Harrelson. Thanks for the detailed breakdown.
@stuzman52 Жыл бұрын
Never heard that I sounded like Woody Harrelson. Now if only I had his amount of money! Thanks for the comment and have a great day!
@user-or6xd2ik1v 4 ай бұрын
Is there sopose to be continuity from the mounting bracket and the power terminal on any starter motor?
@SalientDebate 4 ай бұрын
KZfaq isn't the right placer for support, but no continuity unless your solenoid is engaged. It you measure from the starter's motor terminal to the starter casing or the engine block you should get just a few ohms of resistance. Either Zero or no reading would mean a failure in the armature. @@user-or6xd2ik1v
@paulfoldes3873 2 жыл бұрын
your video are excellent way back your schematics which you rewrite like pro engineer thanks
@stuzman52 2 жыл бұрын
Thank you Paul for the comment and hoping you have a great weekend!
@michaelbradford4444 4 ай бұрын
I needed to know how to remove the clip and I don't have the tools so this was of no use for me.
@stuzman52 4 ай бұрын
Like I showed with a description embedded in the video, you could always use a small screwdriver to remove the clip.
@fieldsofomagh 2 жыл бұрын
Parts still available.?
@stuzman52 2 жыл бұрын
Yes, they are still available.
Real Man Skills
Рет қаралды 2,6 М.
Micks Mowers The Mower Man
Рет қаралды 162 М.
L&M Small Engine Repair
Рет қаралды 2,7 М.
Jeff's Little Engine Service
Рет қаралды 37 М.
John Salt
Рет қаралды 327 М.
fnaguitarplayer9
Рет қаралды 42 М.
Ivan Ivanov
Рет қаралды 1,1 МЛН