👉👉💰❤️😘 @MakeGold remove copper winding from a motor core. How to recycle motor. Scrap the Copper Out of an Electric Motor
Пікірлер: 332
@MakeGold4 жыл бұрын
how to remove copper from motor? I was wondering how to remove the copper from an motor. It is wound around the metal in several different places, and has a heavy papers inserted into each hole where the copper is looped/ The only way I have found is to take a screwdriver and pound each hole with a hammer to push the copper out. I was wondering if anyone had any suggestions. Trying to scrap several motors of there copper.
@AYESHAKITCHENRECIPE4 жыл бұрын
Hi give me your number i want to buy copper armature
@franktracy68714 жыл бұрын
That's too long your losing money taking that long check some of the other guys on utube the use hydraulic knife that cracks the motor shell and the motors insides makes for much easier for scraping the copper
@xorzful3 жыл бұрын
Use a cutter cut the metal in two sided opem and take out the copper😏
@johndowe70033 жыл бұрын
Pull the copper wire out with a winch. Heat up the case so that the glue melts and everything comes out easier
@farukmirza5392 жыл бұрын
mjmt
@tankstrikemouse72066 жыл бұрын
Proud man!!!working hard for he's money!!!And good video!)))
@rukus136 жыл бұрын
Working on the ground would get old very fast, I’d prefer a steel work bench. And could you split or cut the casting at the beginning of tear down?
@georgestyer21535 жыл бұрын
Many years ago, in another life, I served my apprenticship in a motor rewind shop. We used a 75 Volt transformer with a current capability of 400 Amp. This was used in a ventilated chamber to "cook" the windings. A current trip was used to switch off after the windings had burmed and an earth fault was established. 30 + motors a day were treated to this inferno and then passed the following day, after cooling and me removing the copper to the insulation shop then on to winding. In them days a 2 HP single phase motor cost 3.50 UKP to rewind..Ah memories !!!
@MakeGold4 жыл бұрын
Reuse is the most effective secret.
@user-tt5ly2yr7h2 жыл бұрын
@@MakeGold جين جان جون
@josenonato42836 жыл бұрын
Valeu amigo!(Brasil) 👍
@kevinchambers55436 жыл бұрын
Once you remove one end of the coils put it in a fire to burn the varnish off that holds it in place, wires will pull right out by hand on the small motors. Worked in a motor repair shop and that's how we did it but with a controlled temp oven so it wouldn't overheat and ruin the core.
@chick999366 жыл бұрын
but that would devalue the copper by burning it
@kevinchambers55436 жыл бұрын
chick99936 It'll be considered dirty copper anyway since it's coated in varnish, at least it is around here.
@jamesmcfadden87086 жыл бұрын
Scrap yards in Florida will not buy burnt copper, for over 10 years now!
@mikspapa6 жыл бұрын
EXACTLY! Cleaned electric motors for decades here in Missouri. To say this is the hard way is an understatement. Burning doesn't devalue anything. It's still either #2 or refinery #1, depending on where it's sold, and ANY scrap yard in Missouri would buy this in a heartbeat......
@ver646 жыл бұрын
The floor is the work bench for this guy....
@revolution513 жыл бұрын
1:00-Before you take hammer and key steel to knock off the fan end housing: After removing ALL bolts (including bearing cartridge bolts on fan end), take a 6"x6" (or 8"x8")X 4 foot long solid wood timber and hit the fan end of the shaft with one end of it. The weight/momentum of the timber behind the end will send the rotor and drive end housing flying depending on how much force you applied. May take a few bumps, but it will make the job much easier. With rotor and drive housing removed, you can easily remove the opposite drive end housing.
@teodoross86345 жыл бұрын
Nossa vc me ajudou muito eu não sabia como abrir a carcaça do meio,agora posso fazer um mancal inprovisado
@generatorblue6 жыл бұрын
If I had a hammer! I think that you could use a modified jack to do the pulling. You could also make a longer fork that is welded to a handlebar that you can rotate like an alligator to pull out the wires. That left harm must be getting tired after a while, which puts your right hand at risk of getting hit with the hammer. You did good on the first part of the video up to splitting up and removing the motor housing. Good video!
@elams18946 жыл бұрын
Nice to see a tidy workspace for once. The absolute surgical tidiness is more like an operating theatre rather than a workshop.
@taylorbrackeen74854 жыл бұрын
Where did you get those tools
@MrBudd539096 жыл бұрын
different to say the least. Where /How was that notched tool made ?
@Himithor6 жыл бұрын
who need pneumatic air tools when you've gotten good ole air tools.. lol
@nadenitza6 жыл бұрын
Now put it back together!
@rogerconrad85714 жыл бұрын
Wow!!!!! That's a lot of work.
@__austrianoldboy_9861 Жыл бұрын
Love to see recycling videos!
@northernpassed6 жыл бұрын
Amazing how many videos showed up how to scrap motors. After I made mine.
@trig67122 жыл бұрын
A Lot of Work before and after music was brilliant too. many thanks
@Tadek55 жыл бұрын
No tak piekna robota . Tylko, ze na maszynce zajmuje to jakieś 20-30 sekund a nie 12 minut.
@saviolopes85736 жыл бұрын
Very Good!!!!
@ibrahim_Kocak6 жыл бұрын
With a wise and angle grinder it takes less than 5 minutes
@bazoil0076 жыл бұрын
İbrahim Koçak This is Thailand they're still catching up 😉
@meioambientebr1024 жыл бұрын
Magnífico seus vídeos 🇧🇷
@higuinhovidaloka854 Жыл бұрын
Como é o. Nome desse motor
@uglyfrog72635 жыл бұрын
Great music and patience
@darrenarslanian66515 жыл бұрын
I did this job for 3 years and loved every minute. We would use a sledge hammer and power saw , once broken open power saw one side off and then burn them. The copper would then pull out by hand . It was a lot easier than a chisel.
@diwanshusharma1585 жыл бұрын
hello
@jamesmyles34995 жыл бұрын
That’s old school nice job.
@davidbean58076 жыл бұрын
Check out the hammer handle at 11.35. I guess he is prepared for any occasion.
@ArtisanTony6 жыл бұрын
Advice; turn the sound completely off :)
@2Truth4Liberty5 жыл бұрын
And set speed on 2x
@charlesdeconinck6715 жыл бұрын
ArtisanTony biinllolool
@unidesignmovelaria60045 жыл бұрын
Grande bosta !!!!
@TheDeathwalker864 жыл бұрын
Vietnam flashbacks.
@metalmicky4 жыл бұрын
The lads grafting for his bowl of rice. !
@playmaker300024 жыл бұрын
What metal is used in the core the copper is winding around?
@user-hv7ub6sv5v2 жыл бұрын
حديد
@user-ve2mm7gq6x5 жыл бұрын
Эх, жалко такие мощные двигатели я бы на твоём месте разобрал движок затем заменил подшипники и если статор сгорел от дал его на перемотку ил сам перемотал если есть такая возможность , а потом собрать движок и сделать на базе этого двигателя какой ни будь станок .
@TheShowgunofHarlem4 жыл бұрын
A $50 table and a $35 vice would pay for itself in no time.
@louisrichards37024 жыл бұрын
there was a rusty lifting eye bolt on the side of motor case,clean it up and its worth 5$..
@user-cp4is2ih7h4 жыл бұрын
모터에 바킹및고무가 부식되서 해체작업하내요 영상감사합니다!!!
@oneminutefarming95214 жыл бұрын
Lol I did this a few weeks ago out of interest , it was a bigger motor but basically it was 1 1/2 hrs work for 14 quids worth of copper and two busted knuckles !!!. Respect to these guys .
@cw90595 жыл бұрын
Well I suppose that works if you don't have electricity. Personally I prefer using the Press to push out the copper. I suppose you could adapt a log splitter to do the same thing.
@GM-mj6nm6 жыл бұрын
a couple on new bearings and the motor probably would have started again Bad ass
@tonyshifter5 жыл бұрын
It only took 7 years of college and $150,000.00 in student loans acquire this kind of talent.
@vicferrari93804 жыл бұрын
In curious if he hand hurts from hitting it with the hammer?
@alexgiertych51014 жыл бұрын
What’s that tool called at the end that got the copper out?
@Joeo-qk2du Жыл бұрын
If someone was doing this you should cut the end without the power wires and pull from the end that has the wires. I have found that is usually better🤠
@markproulx14725 жыл бұрын
Holy shit, what a bunch of work!
@junioralvessantana74695 жыл бұрын
Com soluções solvente saí mais fácil.
@masr19654 жыл бұрын
Do you sell copper at what price? and where are you located?
@beboploo6 жыл бұрын
was it worth it in that bowl about 2 quid tops
@ahmedbaig72796 жыл бұрын
How much copper is availabe and what is the price? The other worthy elements like bearingse will also be reused.
@adtube41866 жыл бұрын
comments are lame. this guy used no grinder or power tools, A wrench, hammer, and chisels. pretty impressive and the music ROCKS!
@ryanwilson16536 жыл бұрын
Sawzall would help alot. And by the way you spent a few hrs atleast just to turn your 1.25$ electric motor into a pile of copper wire worth 2$. Nicework slappy
@lewrich45 жыл бұрын
Where Did I put those wire snips
@jonstephens685 Жыл бұрын
Good information!
@slowjit90927 ай бұрын
สุดยอดมากเลยครับ
@ThaDIY5 жыл бұрын
ได้เทคนิคใหม่ในการเอาลวดออกแล้วละครับ ขอบคุณครับ
@atarawenh7483 жыл бұрын
بخ بخين تلات بخات 😂
@patrickguillory75525 жыл бұрын
You have to be carful cleaning these electric motor. They are winding the newer electric motors with aluminum.
@ponyrang Жыл бұрын
Wow... !!! My best friend, Great Good... !!! I wish you every day of your development.
@heilmerkelheilmerkel15366 жыл бұрын
Danke für das Video ,und weiter so ...:-)
@user-tn6ry4ge9o5 жыл бұрын
Болгарка и костер в помощь!
@shaikhussain30304 жыл бұрын
How many kg copper does a 1Hp motor contain??
@martybrantley57895 жыл бұрын
Manual Laborrrrrr on this one. I’d be looking for a vice, table , saw or dynamite to get that copper easier. It must be worth something to spend all that time to get it out. Oh and we need some BTO for some better music.
@matthewkyle73706 жыл бұрын
stripping the copper is all fine, my question is, what is the music playing, i have to get a disk of their music ?\!?
@marksmith73654 жыл бұрын
"There's more than one way to skin a cat" as my Granddad would say, awesome video Archi-medes.
@gile8496 жыл бұрын
Noooo, i need that motor
@charlschalo34946 жыл бұрын
I rewind motors even the smallest one but I never feel the need to break the stator,
@joansumagang31176 жыл бұрын
this is the badiest thing to do , here in my place philippines , we rewind that thing , 100% all pure
@TheRustAdmin6 жыл бұрын
that title makes no sense whatsoever.
@hornetobiker6 жыл бұрын
List of possible search terms in wrong box.
@wally80755 жыл бұрын
This has no context but I love to play rust.
@jirihorak5943 жыл бұрын
Good hand job.
@worldsgonemad46002 жыл бұрын
They come apart easier if you boil it in acetone( a bit sketchy but i do it). Also cut other side and push each out with a punch. Takes way less time than dealing with that wound up rats nest.
@ask66075 жыл бұрын
2019????
@miguelmeloelectrico95356 жыл бұрын
Interesante pero mas orden en el trabajo
@richardburgess52156 жыл бұрын
Brought to you by the inbreeds of Deliverance
@carlosdent6 жыл бұрын
Hi, I think if you put some oil on the threads and rusty parts, the engine parts would open better
@ulfhenarpolymathmilitant62585 жыл бұрын
you're working way to hard for that copper..............holy crap !!!
@lucerlich52006 жыл бұрын
Duurd veel te lang thuis werden die motor huisen op een openvuur gezet en utgebrand dan was se draad wikkeling weg en konje de yzerschijfjes zo verzijderen en de draad was vrij
@sailingteslasailingterra43634 жыл бұрын
i think most motor can be fix . this one needet only cleaning from rost the rotor
@erma2476 жыл бұрын
How much of copper was it inside?
@jahsunfire5 жыл бұрын
I so need to make a tool like that. Respect!
@user-fw2en1bu9n5 жыл бұрын
Мы просто сжигали,после пластины сами отламывались.
@renanbcfr73345 жыл бұрын
Um novo tirando aluminio de um motor pirata
@davidmeale95725 жыл бұрын
Jig needed to hold it .
@alwaze10065 жыл бұрын
10:08 There is a face in the glue that's on the wire. I see it Everytime and it's messing with me. 💯
@alwaze10065 жыл бұрын
EVERYTIME!
@wally80754 жыл бұрын
Lol
@manfredpalla1616 жыл бұрын
Mit einer ordentlichen Maschine die eigens solche Motoren öffnet, hätte dieser Arbeiter keine 2 Minuten Arbeit..... Aber wo wird dieser Arbeiter her sein? Kambodscha, Thailand, jedenfalls Asien. 😀😎
@juaneduardobravosunega30266 жыл бұрын
Aqui en chile pais del cobre hay miles de personas que hacimos eso
@jaytiffin77506 жыл бұрын
Cool
@zairijokotolejokotole42306 жыл бұрын
Bermamfaat bos
@guiarunirj8215 жыл бұрын
Eu tiro na metade do tempo sem fazer força
@johngoldman58234 жыл бұрын
What kind of a motor is that ? It's full of copper wiring inside. Where can you buy these scap motors in large quantities ? Maybe 1000 metric tons.
@wally80754 жыл бұрын
All motors have copper inside. At least the ones people sell for scrap
@johngoldman58234 жыл бұрын
@@wally8075 Can you give me their phone number please?
@wally80754 жыл бұрын
Who’s phone number?
@johngoldman58234 жыл бұрын
@@wally8075 Electric motors with copper inside, seller's number, if you have it.
@wally80754 жыл бұрын
They don’t sell them for scrap, they work for people who find the motors and dismantle them. There is no phone number.
@panutuhkanen97266 жыл бұрын
Check the hammers handle and it's figure in 3:23. Hammer for ladies!
@atarawenh7483 жыл бұрын
💃
@ThePoliedrico4 ай бұрын
Posso farti una domanda? Mi hanno consegnato uno statore per moto le cui spire non sono uniformemente ricoperte con la resina. Dovendo andare in bagno d' olio, ho chiesto lumi e mi hanno detto che posso appolicare la comune resina che si adopera per riparare carene in plastica e barche.... corro rischi che se non adatta si squaglia all' interno del motore o che non consenta la corretta dispersione temica... o altro? Grazie molte se potrai/vorrai rispondermi!
@MakeGold2 ай бұрын
Sulla base delle informazioni fornite, l'uso di una resina comunemente utilizzata per riparare carene in plastica e barche potrebbe non essere la soluzione migliore per ricoprire le spire dello statore per motori. Ci sono alcuni rischi potenziali da considerare: 1. Resistenza al calore: Le resine per riparazioni generiche potrebbero non essere progettate per resistere alle temperature elevate raggiunte all'interno di un motore in funzione. C'è il rischio che la resina si ammorbidisca o addirittura si sciolga, compromettendo l'isolamento delle spire. 2. Conduttività termica: Le resine specifiche per avvolgimenti di motori sono formulate per avere buone proprietà di conduzione del calore, consentendo una corretta dispersione termica. Una resina non adatta potrebbe portare a un surriscaldamento anomalo. 3. Adesione e integrità meccanica: Alcune resine generiche potrebbero non aderire bene al rame delle spire o contrarsi eccessivamente durante l'indurimento, causando problemi di integrità strutturale. La soluzione migliore sarebbe utilizzare resine specifiche per avvolgimenti di motori elettrici, appositamente progettate per resistere al calore, condurre il calore in modo efficiente e mantenere l'integrità meccanica necessaria. Queste resine sono formulate chimicamente per soddisfare i requisiti dei motori elettrici. Se si utilizza una resina non adatta, si corre il rischio di guasti prematuri del motore a causa dello scioglimento o del degrado della resina, con conseguenti problemi di isolamento, surriscaldamento e danni meccanici. Ti suggerirei di consultare un rivenditore specializzato in materiali per la riparazione di motori elettrici per ottenere il prodotto più adatto per lo scopo. Potrebbe costare di più, ma garantirà prestazioni e sicurezza ottimali per il tuo motore.
@user-nc9qn4bd3x5 жыл бұрын
Y字型的工具那裡有的買
@juaneduardobravosunega30266 жыл бұрын
Yo haciendo esa pega gane mucho dinero espega pesada chile
@stalincoba88086 жыл бұрын
Ecologic RECIKLE LIKE
@MultiChaga6 жыл бұрын
good music
@ankitmaheshwari67902 жыл бұрын
What is the percentage of copper nice sorting
@southflo40095 жыл бұрын
i thought that was an octopus or something
@alwaze10065 жыл бұрын
F'n HILARIOUS 💯 . Got me!
@CiuciuThe5 жыл бұрын
na miniaturce wyglądało jak potwór, zawodłem się
@marknemecek19685 жыл бұрын
Hear the language in the background that a country where we send our scrap to be recycled that's why no work bench or power tools I believe
@uhmb66556 жыл бұрын
prehistoric work
@pappawheely6 жыл бұрын
it feels good...........
@AbuKompor996 жыл бұрын
its brokhen....
@zajebisty716 жыл бұрын
05.20 wrzuć to w ognisko cały rdzeń się rozleci bez wysiłku
@user-ir4rh8nb6s5 жыл бұрын
แกะแข่งกันป่าว
@Lesnz20094 жыл бұрын
Initially, I thought you were living in the USA due to the music but I see this is not the case and it is interesting how the low-tech approach works
@stopthephilosophicalzombie90174 жыл бұрын
Les Gee What’s the high tech approach?
@Lesnz20094 жыл бұрын
I was impressed with how the person managed to get so much copper out just using manual tools. A Hight Tech approach would be along the lines of an automated process done by a machine or industrial robots to do the work. In developing countries, people have to adapt. Perhaps it is something we in so-called developed countries should seriously think about rather than shipping our rubbish and recyclables offshore.