Tera Low 4:1 Transfer Case Install

Рет қаралды 190,715

8 жыл бұрын

In this video we will install a TeraFlex 4:1 Low Range kit into our NP231 Transfer case for the scorpion crawler. This kit makes your crawl ratio extremely low while still keeping the 1:1 ratio for everyday highway driving.
How to Install an SYE: • How To Install an SYE ...
How to Change an Input Shaft: • How-To Open a Transfer...
Grey RTV: amzn.to/2edMsku
Blue Loctite: amzn.to/2fJcXzq
Transmission Fluid: amzn.to/2et4QRC
Build Thread on:
NAXJA - bit.ly/1nAScEP
Pirate4X4 - bit.ly/1SUlE5O
Website: www.bleepinjeep.com
FaceBook: / bleepinjeep
This product is meant for entertainment purposes only. Your mileage may vary. Do not try this at home. Void where prohibited. Some assembly required. For off-road use only. Slippery when wet. Batteries not included. Do not use while operating a motor vehicle, heavy equipment, cherokee XJ, wrangler TJ, wrangler JK, or any Jeep vehicle, especially the newer Fiat ones. How-to videos may be too intense for some viewers and children under 30 years of age. Please remain seated until the 4x4 ride has come to a complete stop. Studies have shown viewing these videos causes increased cancer risks in laboratory test people. I am not a professional, I have no training, I'm not even particularly good at horse whispering. Don't believe everything that you know. Please keep your hands in the vehicle at all times. Do not tap on glass. Do not eat anything that has been on the floor for more than 3 days. Keep your hands to yourself. Not to be taken internally. Reproduction strictly prohibited. Driver does not carry cash. Objects in Bleepinjeep mirrors may be farther than they appear.

Пікірлер: 184

@gasolinedreams2691 3 жыл бұрын

This man did all of this without cussing or bleeding.

@jacobaaron978 8 жыл бұрын

I about lost it when you said "in my CASE" funniest thing I've heard all day

@mikehoffman3690 4 жыл бұрын

Your knowledge and explanations are wonderful.

@NickInTimeFilms 8 жыл бұрын

Found the same thing when I popped my case open for the SYE. That large snap ring was just floating around in there, but some of the pieces it held in had fallen off and stuck to the filter magnet. That was an interesting find first time around.

@thehellboy567 5 жыл бұрын

I just popped mine open for the sye too and found that same snap ring and a little rectangular sleeve of some sort

@Antiwafflesz 8 жыл бұрын

Nice vid. You are very good at making simple tasks look incredibly difficult though haha

@coldsteeloffroad 7 жыл бұрын

Matt & all who are watching: use a pipe wrench to hold the T-case yoke while torquing the nut...much easier than straps & vises, etc. Also, you don't have to guess when installing/clocking speed sensor...on the side of the sensor there will be a range for tooth count (e.g. 38-45 teeth, etc.). Count the Speedo gear teeth, then align with the slot on the hold-down piece (see Advanced Adapters' ATE install instructions).

@AOT-offroad 7 жыл бұрын

LOL as you were pouring it I was saying "wow I'm really surprised it's not coming out the vent."

@767dag 3 жыл бұрын

Your the paint guy on pbs of Jeeps , just awesome !

@xmo552 2 жыл бұрын

Bob Ross

@mattpiper87 7 жыл бұрын

Great video man, one thing I have found while torquing pinion nuts/yokes for crush sleeves is to use a long pipe wrench on the outer side of the yoke and a breaker bar on the nut and put the pipe wrench at your chest and pull the breaker bar/torque wrench toward you. Works good for 14 bolt gear swaps and would have made this super easy for you. Looking forward to a review of what you think of this setup, getting back into the jeep life and have been considering keeping it mild and doing this kit.

@jakestech28 7 жыл бұрын

Swapping in a Toyota RF1A Transfer Case would be a good idea too. Strong, light, gear driven, and most of all, modular.

@kenadams3951 4 жыл бұрын

nice to see the case apart and parts just to know it. thanks

@MaverickXeo 8 жыл бұрын

What I did for my yoke nuts was take the case and hold it down (like you did) but then take a huge pipe wrench, and use that to hold the yoke in place. It worked pretty well.

@samanthaganzhorn9755 7 жыл бұрын

where do you buy the bigger bolt and spring ?

@No1cares85 7 жыл бұрын

Hey Matt. Great video very detailed!

@bleepinjeep 7 жыл бұрын

thanks man!

@chrissgarage9510 8 жыл бұрын

LOL do an episode like Mr Rogers. Love the show man, keep up the grate work!

@MrMrsregor 4 жыл бұрын

kzfaq.info/get/bejne/n9Fpjcuqxp7Yknk.html

@DrHavok1 6 жыл бұрын

Holy hell this Tera flex kit is EXPENSIVE might as well go get an Atlas especially after also considering having done the sye kit too

@thehellboy567 5 жыл бұрын

but does the atlas 2 work with a yj? I was looking into it but couldn't figure out if it would work for a yj...

@codysett1 8 жыл бұрын

nibbler is called a roloc bristle disk. Be careful when using it around holes that may have things flowing threw them, the plastic dust could clog up the holes.

@ThomasXp 7 жыл бұрын

Great video

@kululv 2 жыл бұрын

great video!

@madmechanix4962 4 жыл бұрын

Haha love this video and love this mod!!

@MrRecklessRC 5 жыл бұрын

Old cheap Tech advice for everyone.... butter knife works really well for seperating gaskets ... the cheaper the knife the better (cause they will deform instead of gouging something expensive)... if you've ever looked in an old Techs tool box and seen a beat up butter knife just sitting there.... thats what its for ;)

@cliffcampbell8827 4 жыл бұрын

I used to have a copper blade with a bunch of electrical tape and a portion of a shop towel for the handle. I don't remember where I got it...or where it went, now I think about it. It wasn't an actual nife (TO HELL WITH THE SILENT "K" IN NIFE!) blade made out of copper, it was something like 1.5" X 6" X .1" copper rectangle shaped to desired dimensions via stone wheel and typical shop use.

@codymoncrief8478 4 жыл бұрын

If you don’t have snap ring pliers, a couple of flat blade screwdrivers, ranging from glasses to standard size, can be used to carefully phanagle snap rings.

@jeepzj2.0 2 жыл бұрын

in your disclaimer you forgot "do not drink transfer case fluid" lol great vid

@Bodeesafa 5 жыл бұрын

Still have mine. Rubicon, Dusy Ershim, Johnson valley, king of the Hammers etc. I guess I’m a lucky one.

@sailorflightattendantaroun9990 8 жыл бұрын

The Best vídeos XJ

@johnrastelli1724 6 жыл бұрын

Please can you do a video ,of the tcases with the NP241 which ones had the mass vibe dampner ,and tcase yokes types ,like flange style...vs classic ...rear tcase and round pinion flange also the rubi 241 driveshafts that all have the round flange ...tks ! Great videos !!!

@evgtorsen 8 жыл бұрын

to tight the yoke i just use a big pipe wrench to hold the yoke and them tight, so no stress in the internals parts with no oil in it.

@Dyllon591 5 жыл бұрын

Would you happen to know a part number for the pressed in berring mines bad and needs a new one I've got the sye kit and driveshaft

@consaka1 6 жыл бұрын

Most shops will just impact drive those big nuts on when you arent looking. They don't bother trying to torque them. The guys that do have a special tool that bolts to the face of the yoke to hold it.

@TehButterflyEffect 3 жыл бұрын

I just got done installing mine. I traded for it. It had a bad bearing that I replaced. Haven't completely finished up the swap yet so I haven't had a chance to test the low range. It won't go into 4 low right now, but I think that will change once I get it rolling.

@NeilWatson 8 жыл бұрын

I cut a piece of bed frame about three feet long, drilled two holes and bolted it to the thing to tighten it down

@glenndavis2762 8 жыл бұрын

+Neil Watson (Miatreya) good job drilling holes in bed frame - the worlds most hated steel (made from recycled railroad iron with high manganese content) - horrible stuff

@ricochetronm5385 7 жыл бұрын

I noticed you didn't fill the yoke spline with RTV like you did in your short shaft video ? did you learn something better? Great job on the how too,I really appreciate them.

@erikbaker174 7 жыл бұрын

I do what your do. What do you do with your old parts you replace? I have a box full of them.

@CrucesNomad1 4 жыл бұрын

Awesome

@abnsoulja1 8 жыл бұрын

I put the mode ring in backwards before. You get 2wd and neutral! I was so aggravated I had to pull it all back apart again.

@evilassaultweaponeer 8 жыл бұрын

Matt, next time you need to tighten any type of pinion nut get yourself a big pipe wrench and use it to hold the side of the yoke. For the t-case it's pretty easy. Rear pinion you'll need to do a few 50lb curls to warm up, but it still works great.

@bleepinjeep 8 жыл бұрын

Good idea, I should have done that when I had it strapped to the table... Sometimes the simplest things can be overlooked!

@jobrogie 8 жыл бұрын

I used a big ass pipe wrench to hold the yoke when I tightened the nut

@fourbypete 8 жыл бұрын

Excellent video, I would never do this, I'd probably buy a rubicon transfer case from the wreckers. Still good to see how it's done though.

@bobkuboske6494 Жыл бұрын

what year rubicon transfer case? I just bought a jeep with one of these in it and it's very loud. I can't even shift it into 4lo with the engine running.

@fourbypete Жыл бұрын

@@bobkuboske6494 Get the same year as your vehicle. Is yours a manual or Auto?

@bobkuboske6494 Жыл бұрын

@@fourbypete 98, automatic. I didn't think they made a rubicon til 05

@fourbypete Жыл бұрын

@@bobkuboske6494 Yeah, I'm not sure. Maybe just do a service on what you have or run a thicker oil. might quiet it down.

@SmudgyContent 4 жыл бұрын

Pipe wrench on the ear press flat on the table would hold it for yah.... similar situation to what i had to do...

@petemcl99 3 жыл бұрын

Great video for a very valuable mod. But it would help if we could download or copy a list of all the new parts that you installed so we could order them. With my luck I would forget to order some small part and have to stop work until it arrived.

@WillS-pl8wg 7 жыл бұрын

Hey matt/ whats your profession,do you do this for a living ? Just curious,and thanks for all the vids 👌

@okiedokie9034 4 жыл бұрын

What size yoke did you put on that np231 are they the ones that fit the full size axle U-joints

@alexanderperez1380 7 жыл бұрын

At 30:35 when you turn the yoke and it makes that clunk clunk sound is that normal? I get that sound out on the trail whenever I'm in 4wd and make any sudden stops, as it will rock back and forth and produce that sound. I've pinpointed the sound to exactly what you did by removing my front driveshaft and putting it in 4wd and rocking the front yoke like you just did. Just wondering as I don't want to destroy my transfer case. Its a 2004 Jeep Wrangler rubicon with a 5 speed.

@markkiger5219 2 жыл бұрын

Matt, I need some advice. I have a 4.0 L with a 5 speed and a 231 TC in my TJ. I am planning a trail build and I have a set of Dana 44s from a Rubicon that I will regear. This option would have been great for me but it has been discontinued. The only available options I can find are sourcing a Rubicon 241 (hard to find) or $4000 for an Atlas. The Rubicrawler is for autos only. Are you aware of something I am missing? Any suggestions would be greatly appreciated. I love your channel and all the good advice you provide.

@neilpetersen5287 8 жыл бұрын

I've seen and used snap ring pliers with knurling on the faces. More grip

@RyansGoslings 8 жыл бұрын

+neil petersen They're called lock rings.

@ferdinandvelez5378 8 жыл бұрын

Next time try using a pipe wrench to hold the yokes while you tighten the nut with your torque wrench. You wont struggle as much! I used this method when I rebuilt my np 242

@DanMcD80 7 жыл бұрын

now would have been a good time for the 2wd low shift fork

@GOD719 3 жыл бұрын

I have an off topic question. If you remove the 4wd fuse. Will it harm the transfer case in "2 lo"? For pulling on pavement?

@RyansGoslings 8 жыл бұрын

Heya Matt... those transfer cases don't have snap rings. They're called lock rings. I remember the first time i asked for lockring pliers at a auto store... they handed me a set of snap ring pliers!

@richlee2576 3 жыл бұрын

Teraflex discontinued the kit. Are there any other options available in the marketplace.

@mikehoffman3690 4 жыл бұрын

You should have sold the shirt as an authentic Matt RTV embossed special. 😜

@ARC928 4 жыл бұрын

Is there a way to do this upgrade with changing only the gears and not the whole T-case half?

@benjaminvolesky1653 8 жыл бұрын

new t shirt idea: "Bleepinjeepers don't yoke around" with a nice lookin SYE for the graphic.

@samanthaganzhorn9755 7 жыл бұрын

what years has the bigger oem bolt ?

@FlamEffect 8 жыл бұрын

Whats your opinion on a 'Hack N Tap' SYE? my old jeep had one and I HATED it!!!! the guy I got it from did a crap job. the normal seal never worked cause it was all wrong. ahhhh

@juanmacias4854 7 ай бұрын

Not sure if you are monitoring this channel, but quick question: I installed a new CenterForce II clutch kit with flywheel, put everything back together and the transmission shifts but no rear tire engagement in 2 wheel drive. I put the Jeep into 4X4 and it works (all wheels turn) in all three 4X4 modes. I assume that something moved in the Transfer case, do you know how I can adjust it to have it engage the rear wheels in 2 wheel drive? Thanks.

@SkyBlueOffRoad 2 жыл бұрын

What was the LONG TERM with this bad boy? Just found a company that makes adapters for the 231J T-case that mates two of them for some doubler action and made me think of this video and wonder what ever became of it.

@zainenewcomb754 8 жыл бұрын

do you know any good ways to make body mounts

@zigz0911 7 жыл бұрын

You know those yokes have two large flat spots on them.......like for a large crescent wrench for example....

@Christophermedynski 6 жыл бұрын

Found a teraflex 4to 1 kit should I send it back???

@robcarruth4187 5 жыл бұрын

The Syncro Sleeve taper end should face the front of the t-case, yours is in backwards.

@billsanchez2665 7 жыл бұрын

Terra flex says there is timing marks on the planitary gears i noticed you werent to concerned with that??

@DustinGould 6 жыл бұрын

where is the bleepin jeep yoke tool ?

@cherrygarcia5514 3 жыл бұрын

Any update on this? Has it been holding up the abuse?

@jacobplace7144 4 жыл бұрын

Is there anything like this kit nowadays in 2020? I couldn’t seem to find it online

@stevecoffman6480 2 жыл бұрын

So now that it's no longer being sold. What's our options without paying for a Atlas or Rubi at over $2000?

@Mikeywil0003 8 жыл бұрын

Would this kit fit on my 2000 Durango? I know that the NP231 in the Durango is a little different, mainly the back half of the housing, the output shaft seems longer, and it doesn't have the speedometer gear on it. If those are the only differences, I don't see how this wouldn't work on a Dodge too.

@notatacoma7621 2 жыл бұрын

I was wondering the same thing about my Dakota

@NK-dl2nc 7 жыл бұрын

Why do you never lube stuff as you assemble it ? You have the ability to do all this work to your Jeep but yet you miss this crucial part of assembly.

@1114flibby 6 жыл бұрын

you should invest in some bearing tools and some seal drivers :)

@cliffcampbell8827 4 жыл бұрын

Why in the hell would ANYONE want a seal driving them around? Always barking, balancing a beach ball on their nose, smell like ocean (or low tide after a bowel movement)...wait, we aren't talking about the same thing are we?

@kidgokuxl 3 жыл бұрын

I think this was discontinued by Teraflex. Sounds like a good idea 💡. Probably didn't sell well during 08-16. A lot of companies went broke back then 😕

@okiedokie9034 4 жыл бұрын

What's the link to order the 4 to 1 transfer case

@brianwaters8408 8 жыл бұрын

Hi Matt. Nice work, quick question. Can't you accomplish a similar result by gearing your diffs deeper? I geared my XJ with 4.88 revolution gears, and run 35" tires. In 4-low it seems to crawl at a nice pace? Thanks for your input. Really enjoy your videos.

@bleepinjeep 8 жыл бұрын

+Brian Waters Yes but 5.13 is about the lowest you can go on the ring and pinion so what happens if you want to go even lower than that? Some people double up T-cases, some people buy an Atlas, or some people install the Tera 4:1 kit. In my crawler I will be running this 4:1 with 5:13''s and 40" tires.

@charlesvilleneuve4052 8 жыл бұрын

Adding a 4:1 t-case also allows you to retain functional high range while having good crawling ability

@briana5444 8 жыл бұрын

Problem with deep gears in your diffs is you're constantly in said low range, with a 4:1 transfer case you can have that 1:1 when you want to cruise on the freeway or drive around town then you can gear down when you'd like to for crawling. Another option is a Klune underdrive although I'm not sure how the prices compare to the Teraflex kit.

@brianwaters8408 8 жыл бұрын

+Brian Athay. I see now. Thanks.

@briana5444 8 жыл бұрын

+Brian Waters anytime buddy boy

@davidtwa8492 4 жыл бұрын

So why is this kit no longer available

@charlesvilleneuve4052 8 жыл бұрын

If the t-case has never been apart or re-assembled properly, the black 10 mm 12 pt bolts will be where the pry points are. As far as I know their only purpose is to show where it is safe to pry

@bleepinjeep 8 жыл бұрын

+charles villeneuve good info thanks

@JohnSmith-qj4cf 3 жыл бұрын

Where do I buy all the parts from please

@ttwilightzzone 8 жыл бұрын

Do you know why they say not to spread the RTV sealant?

@nolanhickson6730 8 жыл бұрын

+ttwilightzzone I've heard a few things: to run a continuous bead, and let the pressure of the bolted piece do the spreading; to spread RTV on one side of the mating surfaces, to ensure that there is RTV across the entire gasket area; or to spread RTV on both sides of the gasket area, to ensure that there are no gaps in the seal, or air pockets that could rupture under pressure, shock, vibration, etc.As far as I'm concerned, I've tried all three, and haven't noticed much difference in any of them. The latter two I mentioned would need some extra care, since air pockets could occur if there was a major void of RTV, or an area where it was much thinner than other areas and the surrounding RTV didn't squish to fill that gap. I have noticed that the latter two do use more RTV, (at least compared to the solid bead method) which could be good or bad, depending on what you're working on.But I think it all comes down to principle more than practice. A clean gasket mating surface and evenly applied RTV (applied in any shape, form, or fashion) should do any job just fine.

@papa54321 8 жыл бұрын

So a 3:21 gear would mean the axle shaft turn 3 times and the wheels turns 21 times Matt?

@xxRamD3yruxx 8 жыл бұрын

+papa54321 A 3:21 Gear would equal to a 0.143:1 so every 1/7 of a turn the drive shaft turns once. a 3.21 gear would be every 3.21 turns the drive shaft (or wheel[s]) turns once. so yes, your right, but in a highly unconventional way of stating gear ratios :)

@Tanner731 5 жыл бұрын

hows this transfer case been holding up? theres one for sale on craigslist around me and I want to put it on my xj with an ax-15

@bleepinjeep 5 жыл бұрын

It broke ;(

@Tanner731 5 жыл бұрын

@@bleepinjeep thanks ill skip that then

@rustybrowneye 7 жыл бұрын

i like the shirt

@arizonacardinals6196 4 жыл бұрын

How much is this part cost?

@n5sdm Жыл бұрын

No longer available. I grenaded mine... over speed. However it was one of the prototypes. Lasted almost 15 years. The rubicon t case slowly killed the demand. Had to put in an atlas. (Not upset...just $$$ more than I wanted.)

@levi8875 6 жыл бұрын

So I installed one of these. 32 months later the Planetary gears blew up. After reading the jeep forums, this seems to be a common problem. Not sure when you made this video, but what are your thoughts on this now?

@bleepinjeep 6 жыл бұрын

+Bev mine blew up too, they discontinued them.

@levi8875 6 жыл бұрын

So other than an Atlas or finding a rubicon TC are there any other options out there? I have a 98 TJ.

@levi8875 6 жыл бұрын

If anyone is interested, I called Teraflex today. They are offering an upgrade program for anyone who had a tera low and had issues with it. Send them back the kit, (has to be less than 5 years old) and they will upgrade your TC to an Atlas for $1900. Still alot, but less than the $2500 it is retailing for. And you have to do something, who wants to go back to a stock 231?

@briana5444 8 жыл бұрын

Here's an NP231 question, my jeep when I have it in 4-lo it likes to pop out on the trail when it gets real nasty. Ideas on why it does that? If I have to rebuild it I'm tempted to do this Teraflex kit, then maybe in the future have a Klune underdrive in front of that... Ooooh

@bleepinjeep 8 жыл бұрын

Could just be the linkage...

@briana5444 8 жыл бұрын

+BleepinJeep yeah could be... Previous owner did it with my SM420 and 4.6 stroker, both of those are shot now so I'm hoping the 231 is okay to keep, save me some dough in the future

@briana5444 8 жыл бұрын

+BleepinJeep you should check out those Klune underdrives. This Tera low kit runs around 1200 and the Klunes are 1400-1600, you can get another 2.72:1 or 4:1 ratios. Then you have the added benefit of having a variety of low ranges to go with, sorta like stacking transfer cases but it adds minimal length to your drivetrain. You could have 2.72:1, 4:1, or 10.88:1 gear ratios just in the transfer case. Multiply on the diffs, and transmission ratios and you could easily be around 150:1 in your lowest range. Epic stuff.

@bleepinjeep 8 жыл бұрын

+Brian Athay I checked the site and it says they no longer make them...

@briana5444 8 жыл бұрын

+BleepinJeep really?!? Dang.. That just ruined my day haha

@davidgould3412 3 жыл бұрын

Why is this still current on you tube , they don't even make that conversion anymore .

@martintaylor984 7 жыл бұрын

Great video, but why not just buy a rock-trac, or save just a bit more money and get an atlas? With that kit and the sye , bearings, maybe that detent you are damn near if not over the price for a base atlas.

@blueboy7256 8 жыл бұрын

So I got a cherokee a couple of months ago and I haven't been able to shift it into 4low. It goes into 4hi and neutral fine but it just won't go into 4low. Do you have any idea what the deal is?

@andrewskorupski7003 8 жыл бұрын

It is most likely the shift linkage that needs to be adjusted. Look it up it takes about 10 minutes to do.

@blueboy7256 8 жыл бұрын

I tried adjusting it but it didn't really help.

@Ghandisgarage 8 жыл бұрын

+Blue Boy then its probably those plastic pads he was talking about.

@bleepinjeep 8 жыл бұрын

+Blue Boy take the linkage off the case and see if you can shift it manually by hand. I have a video coming up that might help you with this.

@blueboy7256 8 жыл бұрын

Alright thanks I'll try that.

@benjaminvolesky1653 8 жыл бұрын

'in MY case'...lol I see what you did there. haha

@ThePete2432 8 жыл бұрын

would I just be better off to but a t-case from a rubicon

@CopeManMTNDEW 7 жыл бұрын

sean peterson I was thinking about that too. By the time you get done ordering all parts like the 4:1 kit, sye, and maybe a tera 2 low... you could get a used rubicon tcase out of a tj or jk for a lot cheaper than this 4:1 kit. If you can locate one lol. I can locate a few where im from for around 800 bucks. The tera low kit is like 1200 or something like that. By the time you get done building it.. your stuck with a rebuilt 231 tcase with only 4:1 low range. so its not really worth it in my opinion. Id rather save up for an atlas 4 speed and have more gearing options and independently control the front and rear axles. But thats just me... ill get there one day. The tera low kit would be worth it if it wasnt so costly. Plus it makes you reuse old bearing or have to buy new lol. I dont like that. If you pay that much for one... shouldnt it come with everything to rebuild it? I love how the scorpion crawler turned out... but its screaming for an atlas tcase.

@smackface6 7 жыл бұрын

i cant find the tera flex 4 to 1 anymore any ideas where i can find one

@bleepinjeep 7 жыл бұрын

+Leadfoot2112 they stopped making them.

@jayraley78 6 жыл бұрын

You will only find one in the trash. They were a great idea, but they could not get them to keep from coming apart. Though I'm sure somebody has one that has never given them a bit of trouble.

@my_name_is_chef4856 8 жыл бұрын

do you need to change gears in the axles at all?

@bleepinjeep 8 жыл бұрын

depends on what gear ratio you need. this case doesn't affect 2wd gearing.

@YouTubeDoxedMyRealName 8 жыл бұрын

What about 4 hi?

@shaunsomma2387 7 жыл бұрын

Adam949 no because the 4-1 is for low range

@robert-bg9pf 6 жыл бұрын

Any time you see something with 1 or 2 fasteners that are completely different than the rest and put in a specific spot that is a FACTORY thing, manufacturers do that on purpose. It's just like putting your locking lug nut across from your valve stem. That specific fastener is put in that spot to act as a sort of "tattle tail" like those Warranty stickers that show show "VOID" if you peel them off. And putting the locking nut straight across from the valve stem acts as a tattle tail for times when you are paying for work on your vehicle that requires the wheels coming off, and if none of the 4 locking lugs are moved, you caught the scamming shop read handed. So in the case of the transfer case, if that tattle tail bolt is swapped for a regular 6 point or gets put in a different spot, that gets used by the dealer to deny warranty repair claims.

@YouTubeDoxedMyRealName 8 жыл бұрын

can't you just drop the transmission into 2nd gear the get a better crawling ratio and that way you can play on the rocks and in the sand?

@jakestech28 7 жыл бұрын

Adam949 Lube is for sloppy anal only

@JS-nk4re 2 жыл бұрын

Why don't they make this product anymore ?

@motherlovinsnuffstar 6 жыл бұрын

I wouldn't mind building one but all the forums say go with an atlas because of the failure rate of the teralow. Anybody have any experience to the contrary???

@bleepinjeep 6 жыл бұрын

They don’t make them anymore

@Christophermedynski 6 жыл бұрын

Well I found a new one from Quadratech.....should I send it back???

@crautoguy8384 6 жыл бұрын

I know the Jeep guys hate Toyota's has been stock there 2.88 to 1 you can get 47 crawler gears and 5 to 1 Crawler gears And gear driven no chain Or planetary cheaper Than a Atlas some Bodyneeds to make an adapter Plus you can run Duels Crazy low rip the spokes Out of mag wheels And teeth out of 44s

@choking0smurf 7 жыл бұрын

Is this case half any good? It has a lot of bad reviews. But that could have been from misuse or bad installation?

@bleepinjeep 7 жыл бұрын

The jeep is just now coming out of the garage, ask me again in 6 months.

@shaunsomma2387 7 жыл бұрын

BleepinJeep 5 months to go lol

@timplessinger3670 7 жыл бұрын

Shaun Somma I'm going to guess bad, because newest video says it went out in him.

@frantinoro 7 жыл бұрын

time's up, how is it lol

@thehellboy567 5 жыл бұрын

@@bleepinjeep so how is it?

@dezertdestroyer7782 3 жыл бұрын

Do they even make this kit anymore I think I want it??

@paytongaines9236 3 жыл бұрын

Nope the kit we discontinued because it would burn up really easily if you do anything more than crawling

@hockeygeek21 8 жыл бұрын

Why dex/merc and not atf +4?

@henrydillard6217 8 жыл бұрын

because dex/merc 3 is what is best for the aw4 transmission so he probably had it on hand. my xj had fresh atf+4 in the trans when I got it, didn't shift right and slipped some, put dex/merc in it and it fixed it, BTW advance auto and the like tell you to put atf+4 in them but there wrong oe spec is dex/merc.

@snowismas 6 жыл бұрын

Next time you clean something with the air grinder step away from the open bearing.

@tooshort3515 7 жыл бұрын

would like to buy this case kit... but i noticed in another video that you said it kinda shit the bed. also another guy on KZfaq said his planetary blew up after 32 months of owning it... can you do a video reviewing your setup and how its working out for you? @bleepinjeep

@bleepinjeep 7 жыл бұрын

+Coltan Vollrath they discontinued them already...

@tooshort3515 7 жыл бұрын

BleepinJeep oh alright. thanks!

@nissan300ztt 6 жыл бұрын

Do yoy still have normal ratio?

@bleepinjeep 6 жыл бұрын

Yes

@nissan300ztt 6 жыл бұрын

BleepinJeep i wanna do this mod. But my jeep is old and probably not worth doing it.

@nissan300ztt 6 жыл бұрын

BleepinJeep Are you canadian? Because you sound so much like Red Green its scary.

@QuantumMind88 7 жыл бұрын

Ok, I'm confused here. You took out all the parts from old half case and put them in the new case, but how does that allow you to have a new lower gear ratio? I'm sure I'm missing something. Nonetheless, excellent video!!

@jakestech28 7 жыл бұрын

Paul Moore The planetary gear set is different.