Testing 5 Off the Shelf Home Depot Recessed LED Light Fixtures

Рет қаралды 30,000

2 жыл бұрын

Light Fixture # 5 was First Place Winner
Light Fixture # 1 was Second Place Winner
Light Fixture # 3 was Third Place Winner
Light Fixture # 1 Link
www.homedepot.com/p/Commercia...
Light Fixture # 2 Link
www.homedepot.com/p/Halo-HLB-...
Light Fixture # 3 Link
www.homedepot.com/p/Commercia...
Light Fixture # 4 Link
www.homedepot.com/p/Commercia...
Light Fixture # 5 Link (WINNER)
www.homedepot.com/p/Halo-8-in...

Пікірлер: 27

@Crooklynmike Жыл бұрын

Hi Ken, Amazing video. Thanks for your effort in putting this together! This takes the guess work out of purchasing these different products!

@bergdaniel6998 Жыл бұрын

I have found that the WAGO wire connectors are superior to wire nuts, in many ways.

@gund89123 6 ай бұрын

Great research, was really helpful. I am in the process of installing recess lights, I am in research phase.

@jerzeedivr 11 ай бұрын

6"-8" Look like 1970's. I only install 4" for myself! Retired Sparky!

@rickhoffman7656 11 ай бұрын

Thank you so much, awesome video

@lakshminakirikanti507 Жыл бұрын

Amazing video and excellent details

@growman88-hz3de Жыл бұрын

Hi Ken, Nice video. One of the things that I have been considering in the room that I am adding lights to, is leaving enough room between the fixture and wall to not have to deal with the glare. I wonder how that might change lumen readings as well. I hadn’t thought about that until I saw your video. Thanks for sharing!

@jpjp3873 Жыл бұрын

That’s some jacked up drywall!😂

@tjcuillier7024 Ай бұрын

Testing was great, provided good information. Unfortunately, I'm looking for kitchen lighting and was hoping to see how the lighting hit on a countertop. I had also been leaning towards 4" for a more modern look. Maybe I'm wrong on that, not sure.

@KenTraining Ай бұрын

I think you should pick either 4" or 6" and just provide more lights to prevent shadow lines and you will not have to run them 100 full bright to prevent blinding. choose the light with different light colors and dimmable and you will be good.

@90thHeavyBG Жыл бұрын

Recently put in Halo 6” canless ultra thin. Did not like the glare off the edge. Changed to Halo 6” direct mount baffle trim and …. Lot less edge glare and looks classier. Easy switch between the two, using the hand tighten connector.

@agapolanskachung3866 4 ай бұрын

Thank you for your informative video! Great information. I have a new construction house with already installed retrofit LED recessed light similar to your light # 1 going into a can. I bought replacement lights that are sagging. Thinking about putting in those wafer lights instead. Can a wafer light go into a can?

@KenTraining 4 ай бұрын

they have LED lights that are can installation model.

@IndependantMind168 Жыл бұрын

I think my laundry room could use that 8" and the 6" would work better in numbers for my kitchen and front room. Nice review of these models. Do the backs of these have to be open air? Ie. You can't cover them with the insulation. I have a single story and the roof and trusses are the ceiling above the main living space. I'm concerned about heat loss. I'd image so, just figured I'd ask. I didnt know about that IC rating until this video. First time home owner and I'm gonna need to replace fluorescent ballast's in the near future. I keep joking that the lighting here reminds me of a Bingo hall.

@KenTraining Жыл бұрын

as long as your installed product say "IC rated", you can have insulation in direct contact and still meet code.

@robertglover8819 Жыл бұрын

It’s tough discerning quality of led fixtures. I’ve noticed also that some flickered on video taken in slow motion on the IPhone. That can reveal a potential issue for folks who suffer from migraines or need to do a lot of reading when lit by a flickering led. No one wants eye fatigue. I found Kichler brand has no flicker on slow motion video. I’ve tried the one shown here with the baffle and it had perceptible flicker. Thanks for testing these lights. 👍🏻

@Search4TruthReality 7 ай бұрын

Heads up on recording any LED device: 1) All LED devices supplied with AC power flicker at a frequency not discernable to the human eye. 2) Be it old CRT displays, CRT television sets, or LEDs soldered to a circuit board, flicker becomes more evident on video recordings when the camera's recording frame rate (such as 24 frames per second) is not synchronized with (or, generally speaking, evenly divisible by) the device's flicker rate, which is usually the same as the AC power frequency (60 Hz in USA, 50Hz overseas). Trivia: for those of us who used CRT computer monitors (think in days of IBM 286 XT Personal Computers, etc.), we would have to increase the monitor's refresh frequency to avoid eye strain and headaches.

@latinhorse75 Жыл бұрын

How did you power the switch, please? I want to test some out before I install them.

@KenTraining Жыл бұрын

very simple, I used an extension cord and cut off one end and hard wired to switch and lights.

@oddopops1327 Жыл бұрын

👍👍😊😊

@KefirTView Жыл бұрын

What's your take on those MUCH cheaper eBay wafer recess lights? Conduct a test with those. All the cheap brands against each other and where they may be prone to fail

@KenTraining Жыл бұрын

I will see what I can do. I totally hear you because they put in at such a low price, you want to move forward with them. I will try them on my next project. On a worst case scenario, I loss a couple hundred bucks.

@KefirTView Жыл бұрын

@@KenTraining I will share with you that there's a specific cheap eBay sold wafer lights I purchased (6 pcs) that ALL went to crap, i.e. flickering, strobing or entirely not working. I opened them up and saw that they're all using super cheap capacitors that have all failed.

@KenTraining Жыл бұрын

@@KefirTView you get what you pay for...