Testing a $125 2-channel portable oscilloscope (Hantek 2C42 Review)

Рет қаралды 210,564

2 жыл бұрын

I recently reviewed and tested a $60 USB 2 channel oscilloscope. While it worked, it did leave something to be desired. This Hantek 2-channel portable scope is twice the price, is it actually twice as good?
--- Video Links
Budget scope reviews:
Hantek 6022BE Review: • How good can a new $60...
Hantek 2C42 Review: • Testing a $125 2-chann...
Hantek PSO2020 Review: • 3/12 C64 repair using ...
ZEEWEII DSO1511G review: • 4/12 C64 repair using ...
Purchase links:
- Hantek 2C42
amzn.to/3LoSYjC ($122 as of March 2022)
amzn.to/36VsBCB ($125 as of March 2022)
www.aliexpress.com/item/40006... ($109 + $16 shipping as of March 2022)
- OWON HDS242 (direct competitor)
amzn.to/3INGxvK ($136 as of March 2022)
amzn.to/3Div4Dr ($135 as of March 2022)
www.aliexpress.com/item/10050... ($101 + $19 shipping as of March 2022)
Adrian's Digital Basement Merch store:
my-store-c82bd2-2.creator-spr...
Adrian's Digital Basement ][ (Second Channel)
/ @adriansdigitalbasement2
Support the channel on Patreon:
/ adriansdigitalbasement
-- Tools
Deoxit D5:
amzn.to/2VvOKy1
store.caig.com/s.nl/it.A/id.16...
O-Ring Pick Set: (I use these to lift chips off boards)
amzn.to/3a9x54J
Elenco Electronics LP-560 Logic Probe:
amzn.to/2VrT5lW
Hakko FR301 Desoldering Iron:
amzn.to/2ye6xC0
Rigol DS1054Z Four Channel Oscilloscope:
www.rigolna.com/products/digi...
Head Worn Magnifying Goggles / Dual Lens Flip-In Head Magnifier:
amzn.to/3adRbuy
TL866II Plus Chip Tester and EPROM programmer: (The MiniPro)
amzn.to/2wG4tlP
www.aliexpress.com/item/33000...
TS100 Soldering Iron:
amzn.to/2K36dJ5
www.ebay.com/itm/TS100-65W-MI...
EEVBlog 121GW Multimeter:
www.eevblog.com/product/121gw/
DSLogic Basic Logic Analyzer:
amzn.to/2RDSDQw
www.ebay.com/itm/USB-Logic-DS...
Magnetic Screw Holder:
amzn.to/3b8LOhG
www.harborfreight.com/4-inch-...
Universal ZIP sockets: (clones, used on my ZIF-64 test machine)
www.ebay.com/itm/14-16-18-20-...
RetroTink 2X Upconverter: (to hook up something like a C64 to HDMI)
www.retrotink.com/
Plato (Clone) Side Cutters: (order five)
www.ebay.com/itm/1-2-5-10PCS-...
Heat Sinks:
www.aliexpress.com/item/32537...
Little squeezy bottles: (available elsewhere too)
amzn.to/3b8LOOI
--- Links
My GitHub repository:
github.com/misterblack1?tab=r...
Commodore Computer Club / Vancouver, WA - Portland, OR - PDX Commodore Users Group
www.commodorecomputerclub.com/
--- Instructional videos
My video on damage-free chip removal:
• How to remove chips wi...
--- Music
Intro music and other tracks by:
Nathan Divino
@itsnathandivino

Пікірлер: 395

@DarronBirgenheier 2 жыл бұрын

When I was a kid 40 years ago, and first getting interested in electronics, an oscilloscope seemed like a totally unobtainable tool for a casual hobbyist. It's pleasing to see that for so little money, a useful scope can now be bought new.

@adriansdigitalbasement 2 жыл бұрын

It's so true -- 20 years ago something like this for so little money was unimaginable!

@DarronBirgenheier 2 жыл бұрын

@@adriansdigitalbasement I can think of few better ways to introduce a beginner to electronics than to have them be able to SEE what a circuit is doing in real time. This takes some of the mystery out of electronics (or adds to it? It's rather astounding to contemplate the usually-invisible forces at play, acting at unimaginable speed, and with precision and repeatability unknown in the realm of physical machinery).

@crazyedo9979 2 жыл бұрын

You are so damn right.😉

@user-yr1uq1qe6y 2 жыл бұрын

I was lucky someone donated a vacuum tube based Tektronics to me 30 years ago. I didn’t realize how awesome it was until I saw the list price of the “solid state” ones back in 1988.

@crazyedo9979 2 жыл бұрын

@@user-yr1uq1qe6y I started with a barn find voltmeter from the 1930's and an ampmeter salvaged from an abandoned truck.😁

@OnHoldAt50 Жыл бұрын

As an electronics tech with seemingly your comfort level (and my owning the upgrade model of that with the AWG/waveform generator) feature- I completely appreciate the time you took to cover the abilities of the scope-meter. Your analysis went beyond just looking at a waveform, but taught some noobs about why it would be beneficial by your real world examples. Arguably one of the best of any scope reviews I've ever seen. * I would have liked to see you cover the DMM and capacitance meter features more thoroughly, but understand the complexity of a scope demanded that time. I really enjoy the large numerical readout with super high contrast (and easy to read green/blue). And it's super convenient to take a voltage reading, then switch back to scope mode without every having to reach for another meter. Thanks Adrian - subscribed. (PS, I learned something about a feature I didn't know until you showed it).

@EPtechser 2 жыл бұрын

Great video Adrian. Try switching the trigger mode from "auto" to "normal". In auto mode, the trigger will be forced at a certain interval. In normal mode the trigger will only occur after the trigger condition, ex. falling edge. You can use "auto" trigger to search for a signal when you do not know exactly what to trigger on. Then you can determine a trigger condition and switch to "normal" triggering which should give you a more deterministic trigger.

@alidanish6303 10 ай бұрын

I have started building my own lab for electronics as hobbyist due to my background in EE, and boy I am hooked to your channel. It is been years I have touched DSO and machines but your videos Adrian has refreshed all that knowledge, Thank you for such an amazing content and hardwork. I can only wish for you that the content brings all the benefits you need. I can see the hardwork that you put high quality video. You have knack for pedagogical skills and I must commend you for that.

@MrPDawes Жыл бұрын

So glad to see an appraisal of these Scopes. Always considered them to be a bit too expensive to take a punt at one hoping it's any good. This one looks very attractive. I could use one with a signal generator for checking transfer character of analogue stages in the field. Thanks Adrian, for an excellent video.

@jameslewis2635 2 жыл бұрын

While this is by no means a pro level piece of kit, the fact that it has multi-meter functions as well as the oscilloscope function while remaining pretty affordable makes this sound like it is probably quite a nice little unit for a hobbyist or a student getting into electronics.

@bskull3232 2 жыл бұрын

Cheap things do work. In fact, my most used tool is a $179 Analog Discovery Gen 1 bought on sale. I think it is now $279 or so, but regardless, a very cheap 2-ch AWG, 2-ch DSO and 16-ch pattern generator or logic analyzer. Sometimes those cheap things are quite easy and handy to use, especially when all you need is functionality, not performance.

@appliedengineering4001 2 жыл бұрын

I would never use something like that in a lab. But for out in the field use. That would be an excellent scope to have.

@kitbuny 2 жыл бұрын

I've been looking to get into electronics myself and have been told by a few other friends that this would definitely fit the bill for someone like me with very basic knowledge who is still learning, with plenty of functionality to keep me going until I will inevitably need something more. I'm going all in on this but unfortunately don't have a lot of money right now so this is right within my price range.

@SonicBoone56 2 жыл бұрын

It's looks like an easy way to learn how scopes work tbh.

@OzRetrocomp 2 жыл бұрын

Agree. This looks like a great first scope for a student or casual user. The best bit is that even when/if the user buys themselves a bench scope, they'll still have a portable scope on hand for field use or as a spare should their main scope develop any problems.

@Alkatross Жыл бұрын

Thanks for the walkthrough of the 64. Nice to see what pulldown resistors actually look like on gpio pins. That's a great way to demo the scope also. Thanks!

@MatroxMillennium 2 жыл бұрын

I had been looking at these but wasn't sure if I wanted to actually pick one up. Appreciate the review!

@adamwheeldon 27 күн бұрын

Thank you Adrian for a very thorough and informative review - I purchased on your recommendation

@fredflintstone8048 2 жыл бұрын

Nice evaluation, thanks for sharing. I have an old battery operated portable Tektronix scope that I like for the same reason you've pointed out. It's always isolated from whatever you're connected to which makes it safer and more flexible in some applications. The portable Tektronix scope was far far more expensive and was sold back in a time when the dollar was more valuable than it is today and had fewer features than the hantek. Rigol is another manufacturer that's built one model on the assembly line and then sold it with different features for different prices where the only differences were in the firmware. It doesn't surprise me to see the function generator bnc connector there but basically not turned on. It also doesn't surprise me to see that they're using the center of the bnc connector as the output where you put the point on the scope probe to calibrate it. I have a number of Tektronic scopes and they're all the same in that they have a similar small round opening to put the point of the probe in to get the calibration square wave, never a loop for a hook lead. However they also have made models that provide a U shaped bar that you can use the press on hook lead on which is nicer (hands free).

@macdaniel6029 2 жыл бұрын

Thanks Adrian. I own this Oscilloscope for some time and now I understand it much better 🙂

@mndlessdrwer 2 жыл бұрын

The VHS-quality intro always hits that peak nostalgia part of my brain and primes me to have a good time with these videos.

@jarvishill1007 Жыл бұрын

Adrian, at 75 now, after Vietnam Naval Avionics Advanced Maintenance, nicked named, "Mr. Scope", very much appreciated this review with experience and passion for the subject. Without explanation, my $2,000.00 Textronix Scope is over 10% out of calibration & questionable to use from in house storage. Motivated by car problems, have a renewed interest in an automotive scope to see the CAN Network and have been looking for a portable scope. I feel it adequate for general waveform diagnosis, with experience to interpolate through inaccuracies for automotive diagnoses at a poor Navy Veteran's forced early retirement. (Trouble shooting my primary 20 year old car) while driving 2nd 26 year old car. The new digital scopes have so much expanded capabilities over the older analogue scopes, your coverage is so a appreciated! After much research & your KZfaq, I ordered the Hanmatek HO52 scope meter. (Hanmatek H052 scope/meter?), Oops? (?Hantek?) Oops? Adrian, thank you, from an old salty Navy Avionics AMD Technician!

@cryzz0n 2 жыл бұрын

Love the video, luckily I found a gem of info for expanding the functionality of the 2C42 model that I have aswell (purchased mine in 2020 for $90 on aliexpress). I have modified mine in accordance with the changes that nickbel recommends to get the arbitrary waveform generator working, and better sensitivity in the probe op amp based amplifiers. All that they did to release cheaper models was to remove a few chips and the chip's strapping, all the firmwares are the same. First among my modifications was adding a DAC902E burr brown chip and strapping, and using salvaged smd tantalum, mlcc, and resistors to strap both the awg output op amp circuit and the AWG's DAC. Next was adding op amps, AD8009 to be exact. I replaced only one of the probe op amps with an AD8009 to compare performance of both amps- nickbel already did this in his videos. I filled the empty awg gen amp position according to what nickbel shows in his forums and videos, and have been happy with a working AWG. Also BAV99 SOT-23 diodes are necessary. I have pics of my modifications before and after alterations if your interested. Nickbel has a full forum and youtube(subtitles necessary) channel, he's a russian ee engineer with some useful information.

@patriziopolcri995 2 жыл бұрын

Very nice review Adrian! Cheers from Italy

@jimw.4812 Жыл бұрын

I saw a Tektronix scope at a trade fair. I was so impressed, I spent the next 25 years repairing them. Love this little scope! Awesome.

@barrymayson2492 2 жыл бұрын

Hi great video. I bought one of these with waveform generator. Must admit that I don't use that bit much. But it's was a great tool as I was away from my lab for many months due to COVID. So it worked well for me in a temp bench in my sister's spare room . I would definitely recommend one from my experience. Thanks for the video.

@azurehydra 2 жыл бұрын

Very good. Helpful review. Might pick one up

@MicrobyteAlan Жыл бұрын

Thanks, I was looking for a good inexpensive scope, mostly for troubleshooting SBC breadboard circuits and other things where seeing what’s going on is helpful. I just ordered one, should be here tomorrow. 👍👍

@TheElectronicDilettante Жыл бұрын

Thanks for the review. I was on the fence but now it’s in my Amazon cart. You should get Hantek to send you gear to review, you do it well. Thanks again! - Jason Burchell

@barrykery1175 2 жыл бұрын

Good review / demo. I have the Owon version of a hand held oscilloscope and they are really neat. I just love the idea where the manufactures include a VOM within the design. It makes for a great carry around trouble shooting tool. I've never owned a scope before but now that I have my hand held scope, I'll never be without it. They are great ! Barry, KU3X

@borayurt66 2 жыл бұрын

Great review, and good catch on the power off battery drain. Rule of thumb is; if a rechargeable device you just purchased new comes out of the box completely drained, there is a problem there.

@jclosed2516 2 жыл бұрын

Nice review. It's a good one to have around, that's for sure. I had my eye on this model, but also on the comparable Owon range. After much considerations I went for the Owon HDS242S. At €165 I got a 40MHz model with build-in function generator. The Hantek model you have was about the same price (€160), but (as you noticed) without that function generator (by the way - prices here in Europe are inflated by VAT and import costs). For me a handheld just covers my needs. Sure - I had way more expensive bench models in the past (I did run a consumer electronics repair and recycle shop a few years ago), but for my moderate needs nowadays such a hand held is more than enough. The build in function generator and (actually rather good) multi-meter functionality makes these hand held models a good all-rounder for repair jobs.

@GoGlennR Жыл бұрын

Great review! 👍 Thinking about buying one of these. 🙂

@Savan_Triveda Жыл бұрын

Very profound review. I start to like the Hantek.

@TheElectronicDilettante Жыл бұрын

I was just on Hanteks website and they offer pc software to view oscilloscope data from the handheld on the pc monitor. It’s pretty cool and looks better than the usb scope you demoed . Thanks again

@MattSiegel 2 жыл бұрын

great review!! and interesting C64 facts :)

@coptertim Жыл бұрын

I've had a 2D42 for 2 years and it's great. It won't replace my desktop scope but having a basic AWG, multimeter and scope, all in one, has been a big help for off bench projects.

@BoringCooking 2 жыл бұрын

I had been looking at these scopes, so thank you so much for your reviews. If you happen to do any more of these inexpensive scopes, could you look at the PicoScope 2204A? Thank you again for the effort you put into these great videos.

@tOSdude 2 жыл бұрын

Ah yes, perfectly timed. I just bought a cheapo oscilloscope yesterday. I'll see when it arrives whether I should go back and get something like this.

@placebomessiah 5 ай бұрын

I just ordered an Analog Discovery 3 by Digilent and this video was so educational, I'm feeling less intimidated by the terminology of this particular tech. There's a bunch of terms that are the same but different in the DSP realm, so it was nice to see the clarification.

@tohaason Жыл бұрын

This scope seems to be so much better than the previous one (on which I commented that I much prefer stand-alone units, and other things). This actually looks useful.

@jamesdarlack4898 Жыл бұрын

Wow. Another great review.. i just might buy one... OK, the challenge is,what is the next better low cost scope??? Keep up the good work, we all appreciate your efforts.

@jeffwormsley7425 2 жыл бұрын

Bought one for work a couple of months ago. So far so good, but I absolutely had to change the timeouts for turning the screen off. It was very annoying looking away to work on something and looking back and the scope had shut down.

@OzRetrocomp 2 жыл бұрын

I was seriously considering the Hantek 2C42 as my first portable oscilloscope a little while back, but funds were tight at the time so I went for a cheaper single channel scope (FNIRSI). It does the job but in hindsight I wish I'd waited a little longer and bought this Hantek instead. Thanks for the detailed review.

@adriansdigitalbasement 2 жыл бұрын

I know those little single channel ones do work -- and I think they cost like $60 USD? I'd say they are similar to the $60 USB one I reviewed, but a lot worse and more cramped, so for that price bracket, the USB Hantek is the way to go. Two channels and a much easier to use UI ...... but this device really is pretty good, I'm definitely impressed.

@theshaggyfreak 2 жыл бұрын

I just picked up the Owon 70mhz handheld and I think it will work well for my basic needs. It’s a bit more expensive but seems to do the job and Auto is pretty quick too.

5 ай бұрын

amazing review, RIchard Dreyfuss.

@KissAnalog 2 жыл бұрын

Nice review!

@mike94560 2 жыл бұрын

I like mine. I can take it outside and have a usable scope with me in strange places.

@sonjas.606 2 жыл бұрын

uh got a hantek lab power supply in january, its fab! Now listening on your thoughts on the oscilloscope 👍 Lready love the illuminated display

@TechSponsorTV 8 ай бұрын

Thank you, you've noted some important aspects that can help me with designing a better cheap oscilloscope based on STM32H7!

@antonioastorino7488 Жыл бұрын

I'm impressed. Thank you for posting these videos. At 37:47, I think the connection to ground should be checked against the actual ground pin, not the connector shield - that is not always connected to the ground pin.

@TRONMAGNUM2099 2 жыл бұрын

I bought this scope a while back for my job. It works fine for my needs. I don't use it all that often, so I always forget the menu structure. Other than that, it was a pretty good purchase, and I am glad I bought it.

@nezbrun872 Жыл бұрын

That's the biggest problem with handheld scopes, the UI.

@darrenthompson3696 2 жыл бұрын

Hi Adrian, I have had couple of Hanteks in the last 2 years and have found calibration issues with them. The OWON is significantly better. The display is also much clearer on the OWON

@additudeobx 2 жыл бұрын

Great Vid, very informative, you sound like you're on your game and in your element... and... I'm not complaining, just noticing... but at 28:38 that component, is not an inductor. It's a PTH Resistor. Also, all of those components on that 64 board are ESD sensitive and you are not personally ESD protected. If you want to see the battery current draw while charging, power off the equipment first so you are not measuring equipment current draw as well as charging current. I was impressed with that handheld scope for the price. For the everyday tech doing signal chasing that scope carries a pretty big punch for the price. Strap a battery backpack on it as necessary, the scope operates while it charges and I'm sure it will last operational all day. Thanks for the show and tell.

@joaogoffredo 2 жыл бұрын

About USB connection in 37:18. It does not necessarily grounds the oscilloscope. It can have a DC-DC converter with first and second stages isolated each other. En the signal can use optoacoplators. I have an old Micronta Multimeter with RS232C, and it is isolated from the multimeter. It only works if some signals are supplied to power the RS232 multimeter output circuit. Update at 37:30: You told what I was thinking about isolation. Update at 37:50: You did the test I wanted to see. THANK YOU. I missed how to change the battery.

@gabrielleeliseo6062 2 жыл бұрын

Love the video. I think I’ll just save up for a nice new scope. Maybe I’ll luck out with a nice used one.

@rickeymh Жыл бұрын

in 1983 I purchased a used, non-working 100 MHz HP O'scope for $750. I was able to fix it with about 6 hours of troubleshooting and $18 service manual. That was an excellent deal back then.

@overlord5066 2 жыл бұрын

Great timing! I'm an automotive electrician and looking for a half decent scope for probing sensors/computer networks/etc. I think the only thing that may be an issue is the screen size/visibility off angle. Do you think the second one you linked with the bigger LCD would be a better choice? I don't need any real fancy features seeing as 9/10 its just for confirming a signal exists rather than what the signal is actually doing. I was actually looking at one of the hantek PC based scopes (hook it into the workshop PC) but seeing as these seem to do PC passthrough, best of both worlds (actually do they? or is the PC software just for displaying saved captures? Not live view?)

@Dave5281968 2 жыл бұрын

Excellent review. I like that your review is coming from a point of view from someone that is not accustomed to years of using very high end scopes. (Those that have used high end scopes for years pretty much always give every low cost scope a bad rating since their opinion of minimum quality is very skewed toward a $100,000 scope.) PS: You mentioned the logic level problem with mixing TTL and CMOS logic. The other huge issue is that when TTL receives the nearly rail-to-rail signal from CMOS there is very high current draw at the TTL input. Conversely, when CMOS receives a signal from TTL there is also very high current draw at the CMOS input. (This, of course, applies to devices using totem pole outputs being connected to totem-pole inputs.)

@Graham_Wideman 2 жыл бұрын

" when TTL receives the nearly rail-to-rail signal from CMOS there is very high current draw at the TTL input. " Not true, assuming both are powered by 5V, "Conversely, when CMOS receives a signal from TTL there is also very high current draw at the CMOS input." Also not true. The only way to get a high current at a CMOS input is if the driving signal exceeds the voltage of the input protection diodes, so more than 0.7V above the positive rail, or below the ground rail. "This, of course, applies to devices ... connected to totem-pole inputs.". There is no such thing as a totem-pole input.

@appliedengineering4001 2 жыл бұрын

So a TTL output driving a CMOS input can cause overcurrent. A CMOS input can be driven from rail to rail, were as a TTL output only drive 0.6 of a volt from the rails. A TTL can drive a CMOS just fine with room to spare.

@Graham_Wideman 2 жыл бұрын

@@appliedengineering4001 "a TTL output driving a CMOS input can cause overcurrent" -- no it cannot, assuming CMOS is running on 5V same as TTL. If you disagree, please tell us where in the CMOS chip that current goes. "A CMOS input can be driven from rail to rail, were as a TTL output only drive 0.6 of a volt from the rails." First off, a TTL output is asymmetrical, with typical output 2.4V for high (with very little pull-up current capability), and usually more like 3.5 to 4V for no load (which is what a CMOS input looks like). Whether or not the CMOS input correctly responds to the TTL output depends on which CMOS family it is. Some have explicitly TTL-compatible inputs (such as 74HCTxx series), and others do not, for example having 1/3 and 2/3 thresholds (which may still be fine, especially with a pull-up resistor on the TTL output). " A TTL can drive a CMOS just fine with room to spare." You just claimed that the output swing of TTL is less than the range of the CMOS input, and though you got the values wrong, the idea is correct. If the TTL swing is less than CMOS, where it the "room to spare". Perhaps you mean that the TTL output swing is at least large enough to cover the thresholds of the CMOS input. That may or may not be true, depending on CMOS family, as I noted.

@TrimeshSZ 2 жыл бұрын

@@Graham_Wideman Across the power lines. Take a look at the datasheet for a typical TTL chip and you will see that VoH(min) is typically specified at something like 2.7V,. while ViH(min) for a CMOS part is typically something like 3.5V - so an (in-spec) TTL part can drive a CMOS input with a signal that's outside of it's drive spec. Since CMOS chips (naturally) have complimentary input structures this sort of "above ViL(max) but below ViH(min)" can cause both FETs to be partially turned on and this is turn can cause excessive power dissipation. Sure, most of the time it works fine because the actual output voltage of the TTL part is above the linear region of the CMOS part, but checking the datasheets clearly shows this cannot be assumed. Note that connecting 3.3V CMOS logic with 5V TTL does give sufficient margin in both directions - which is precisely why that 3.3V supply voltage for CMOS was decided on in the first place.

@Graham_Wideman 2 жыл бұрын

@@TrimeshSZ " Across the power lines." Ie: current through the two complimentary transistors both being partially on. Yes, I agree, and I noted as much, suggesting, for example a pull-up resistor to ensure fulfilling logic level requirements when interfacing TTL to a non-T CMOS family. However, that does not speak to the comments I was responding to, which claimed excessive current into or out of the CMOS input itself. I concur that the datasheet specs oblige treating the possibility of an ambiguous voltage from the TTL output, even if in practice it may not be an issue.

@goranekstrom708 2 жыл бұрын

If you still get a signal when shorting the probe to it's ground lead doesn't necessarily mean you have a bad ground lead, the loop from the probe tip to the ground clip works like an electromagnetic pickup, creating a makeshift EMC probe.

@stefanweilhartner4415 2 жыл бұрын

i have the hantek 6254bc usb scope it has 1GSamples shared with up to 4 channels. for about 250$. i was really impressed!

@IvnSoft 2 жыл бұрын

Thanks for the review. I wanted one of these handhelds, but there are so many brands/versions that it is just impossible to decide just on the info (which usually is scarce and badly translated). I just ordered the OWON, just for the bigger screen, and to check how different it might be.

@hansschneider4574 2 жыл бұрын

Nice review! I think 13:10 is rather a sampling or memory depth problem than a trigger problem. 😉

@AfterHoursEngineering 2 жыл бұрын

I have the early model and it works excellent.

@raymiller5738 2 жыл бұрын

Thanks for the video, had one of these for a while, I needed to replace ALL the PCB banana sockets on the DMM as all my standard fluke banana jacks would not fit! I ended up disassembling some panel mount banana sockets and replacing all and now zero problems. I do not understand why Hantek would change the banana socket standard, very poor form and should be fixed. Otherwise, the Hantek is a very good value machine.

@thehearth8773 2 жыл бұрын

I've often wished for an oscilloscope with isolated channels. Tektronix used to make one, but I don't know if they still do; Rohde & Schwarz makes one too, but it's too low bandwidth for my purposes. I don't know why there aren't more scopes that have that; the channel-to-channel isolation especially would be really useful for the types of measurements I do routinely. I get that it costs a bit to add, but surely more companies could at least offer such a scope, even if it cost more than their non-isolated ones. This portable scope won't work for my needs (I need a bandwidth on the order of 1 GHz, preferably a bit more, and I wouldn't trust this thing at 500 V regardless), but it would be nice to see isolated channels on other scopes, I suppose is what I'm saying.

@horusfalcon 2 жыл бұрын

Interesting product. I do wish someone here in the US made a similar product. This leaves the Fluke scopemeters I've used in the past behind for about a tenth of the price.

@stevethepocket 2 жыл бұрын

Even if they did, it would just be outsourced to China anyway and probably be the same quality. Might even just be the exact same product with just enough cosmetic changes to fool someone who doesn't get one of each. Oh, and it'd cost more in spite of all that.

@horusfalcon 2 жыл бұрын

@@stevethepocket Yup. You've pretty much summed it up.

@thethinkerer Жыл бұрын

I love seeing the water heater in the background, it really kinda proves the "Basement" aspect. I hope nobody out there has a fake water heater in the background of a Hollywood studio, cashing in on the whole basement aesthetic.

@nilz23 2 жыл бұрын

I like these reviews and tests of cheap test equipment. Looks like they are getting better and better while the price stays the same. That thing boots up faster than either one of my Tektronix digital scopes. Also that screen can't be that bad, the ones Tektronix at least used to use on its cheap scopes are absolute garbage.

@nilz23 2 жыл бұрын

The funny thing is my old green crt one with a floppy drive boots up faster than my newer one with an lcd screen and this thing is faster than either. I guess the lcd one is easier to carry around though.

@Renville80 2 жыл бұрын

Definitely going to be considering this model. I have a piece of equipment that I want to analyze further but it unfortunately has a ‘hot chassis’ design (meaning there is 120V on the circuit ground even when turned off). I wonder if one is able to make screen shots of waveforms on this?

@amurtigress_mobile365 2 жыл бұрын

Maybe you would want to get an isolation transformer. That you can use either on a hot chassis device OR on an oscilloscope, to interrupt the ground reference...

@agranero6 2 жыл бұрын

The function generator output is there because oscilloscope makers usually make just a model and differentiate them by firmware only. There are cases of oscilloscopes max frequency limited by software and people discovered how to transform them in the more expensive model just changing the firmware.

@Dukefazon 2 жыл бұрын

6:20 - thd model number is on the front, on top of the screen next to the Hantek name (8:20).

@mhavock 2 жыл бұрын

Hey, great video. I was hoping you could also test the 2 channel (at same time) for performance and usability. Maybe for another video. Quick joke: Why did the submarine captain tell the first mate to bring 2 scopes to the bridge? He wanted make a pair o scopes. LOL

@imranahmad2733 2 жыл бұрын

The hantek oscilloscope is ok for vehicle and audio but linearity is not the best, plus the signals can alias, their LCR meter is pretty good, some of the cheap LCD o-scopes like the DSO112A are better because they have 5mV/div, ideal for checking passive sensors and noise, I also use a fluke, Tektronix and agilent but they're not ideal as a first scope due to cost, but the cheap scopes are great for beginners, and as you advance and reach the limits of the equipment you upgrade. There is one other thing with the hantek portable gear, they seem to drain the battery down when switched off, so a fully charged battery will be drained in about 6 weeks, I modified mine to have a hard switch with a diode connected across it so I can completely switch it off and still allows it to charge, it's ready no matter how long it's stored away for when I need it.

@eman59461 2 жыл бұрын

Love all your videos. Great work. I like the owon better . The Owon came out later than this. This is better in a few ways. One of them is the bandwidth The other is computer software. The Owon has a faster refresh rate and takes more power. If i didn't buy my Hantek 2D72 i would have gotten the higher end Owon. Owon came out with a newer model late last year. It is similar to the Owon HDS272 but its 100Mhz.

@OzRetrocomp 2 жыл бұрын

One thing with Hantek is that they're upfront about the capabilities of their gear. When Hantek say it's a 40MHz scope, it's a 40MHz scope. Not sure if I'd trust the specs on an Owon. This comes from a dude that bought a "100MHz" FNIRSI knowing full well it was only good for 30MHz or so but not caring because even 30MHz is more than enough for my use case and the price was right.

@maxagent86 Жыл бұрын

Which version of this would you recommend for automotive work, if any? Thanks for the video.

@ihatesmartphones 9 ай бұрын

I got the high end one. The 2D72. That one came with two scope probes. The AWG works well. If you connect the scope to your computer. You can make your own waveform and it generates it very well. If you can get the Firmware for the 2D72. You probably could load it into yours. It’s cheaper for them to make one scope and then just load different firmware.

@bingosunnoon9341 Жыл бұрын

When I started working for Tektronix, I was suprised that I had to build my own test equipment, including a scope. Luckily, there was an old timer who walked me through it.

@justiszachary Жыл бұрын

I have this exact model and the screen is always randomly dimming. Did you ever find a way to get rid of that. Excellent video by the way very helpful.

@MatthewHolevinski 2 жыл бұрын

The portability of that little scope would be great for automotive uses.

@jonatas464 2 жыл бұрын

I have that 2D72. Main diference between C and D, that D have a functino generation. It's very helpful.

@blueharley2 Жыл бұрын

thanks for helping me not waste my money

@UTRG-UnderTheRain 2 жыл бұрын

I just ordered one of these with the function gen about a week ago just have when I go to customers locations it's decent.

@demofilm 2 жыл бұрын

nice portalble meter, would love to see the internals.

@koborivers Жыл бұрын

I have this scope and the charging circuitry went out after a few months - Still using it by pulling the cells out and throwing them in a lithium charger. Other than that, it's worked pretty well.

@LeeMcc_KI5YPR Жыл бұрын

Keep the Ground lead as short as you can. At those frequencies, it won't bite you too bad, but best practices should be learned early. Also, if designing a board, add Ground points on the board, to make it easier to solder in a pin to attach the scope ground.

@TheElectronicDilettante Жыл бұрын

I’m sure you’re aware of a video that compares the Hantek and Owon hand scopes. If not, you should check it out. Published by Kerry Wong, it definitely depicts the Owon as the superior hand scope of the two. Thanks again for your review of the Hantek.

@SteveJones172pilot 2 жыл бұрын

I got one of these for Christmas, and am excited to have it, but haven't used it much yet. This video was helpful.. A couple comments. 1: Careful you dont lose that extra long USB-C cable.. That jack is so far recessed in there, I'm not sure you could get another cable in there easily. And second, doesn't this have software to use a PC as a controller/display device? I haven't done it, but I thought I read that.

@wbfaulk 2 жыл бұрын

I got an OWON HDS272S portable scope a few months ago. It is *very* similar to this one. The button layout is a little different, but the graphics are identical.

@maebeans 2 жыл бұрын

i have the same scope but 40mhz. tho they may be quite similar to the hantek scopes i'm pretty sure that the hardware is different. the owon has a few annoying little bugs: 1) when you auto capture it often leaves the second channel active, even tho it's not currently in use, so you have to go switch channels before any of the vertical/horizontal/trigger controls work. 2) the multimeter cap tester is so so slow. slower still than you imagine.

@wbfaulk 2 жыл бұрын

@@maebeans Yeah, the multimeter is almost uselessly slow. I went to see if there was a firmware update after watching this video, but no.

@kpanic23 2 жыл бұрын

Hey Adrian! Can you please check continuity between the ground clip and the USB power ground pin? It's quite possible that the outer shell of the USB connector and the ground pin aren't tied together. I don't want anyone to have a mishap when probing a CRT with the scope connected to the charging lead.

@jean-lucpicard8186 2 жыл бұрын

That’s kind-of a redundant test, since whatever you plug it into is going to have the two tied together anyways, but I’ll go grab mine and check. Edit: I'm back with the results. At least on my 2D72 with the factory included USB cable, the outer shell of the USB connector and the USB ground are tied together, while the BNC shells remain isolated from both at all times. I think this'll be the same with all USB cables too, because the shell of the type-c end is also tied to the shell of the type-a end, just like any other cable will be.

@aetch77 2 жыл бұрын

You are correct about the shell being separate from the pins. The usb ground *pin* is tied to the BNC ground. I did some testing on my 2D42. The supplied usb cable is not shielded, the shells of the usb plugs are not connected. When you plug in a shielded usb cable the shell does provide continuity.

@kpanic23 2 жыл бұрын

@@aetch77 Thanks! So definitely no ground isolation while USB is connected. This is important news! You might get away by using an unearthed charger like the one it comes with, but if you exceed the voltage rating of the internal class Y filtering capacitor you might still blow up the charger. Not to mention the leakage current through that cap.

@jean-lucpicard8186 2 жыл бұрын

@@aetch77 Huh, that’s odd, because I just tested my cable and meter again, and on mine the shells of both ends are connected together and to the USB ground pin, but BNC ground is floating relative to USB ground at all times. I wonder if that’s a hidden feature that either upgrading from 2Cxx to 2Dxx or 2x42 to 2x72 gets you?

@0xc0ffea 2 жыл бұрын

Put the model number in the video title so people can find it ! .. YT is the first place I look for reviews of stuff like this

@annieworroll4373 8 ай бұрын

I wonder if it has the full hardware for the AWG, or just the bits that show on the outside? I've got a 2C72 on the way. Basically this thing with more bandwidth. The waveform generation tempted me but I didn't see quite enough of a need for that to justify the extra cost. Hopefully I don't regret that decision.

@smunaut 2 жыл бұрын

Watchout that what you tested with USB is only the shield. In a good design the shield isn't directly tied to ground, it's ac-coupled + high value resistor in parallel. What you really needed to connect to is the GND pin of the usb connector (but it's not easily accessible with a multimeter probe ...)

@Gruntos 2 жыл бұрын

I have the 2d72. Amazing bit of kit Forgot to mention, the multi meter is sloooow to register as it goes through every range. The signal gen is great Lastly. You can use the software to read it, probably the same as you use for the other cheepo junk. (if you have the devils spawn sorry I mean Microsoft ). Be careful if you upgrade it to new firmware lots of bricked devices. I upgraded mine but had to install a vm on my Mac. Works a little faster now. Thanks for the tip on BWLimit

@williamsquires3070 2 жыл бұрын

The reason the func-gen output is there is to save cost; this way they only design one board, have one BOM, and one process for the pick-and-place machine. They just program them at the end based on how many units of each part # (SKU) they expect to sell. And, I’ll bet, even that is automated. This way, if they expect to sell 70 of every 100 as the low-end model, they just hit a button, and the automation programs every 7 units with the base configuration, and the next 3 with the high-end (func-gen) configuration. After that, they get boxed and shipped! Then they use feedback from the inventory-keeping end to adjust the percentage of each SKU. At, least, that’s what I’d do!

@LP6_yt 2 жыл бұрын

Perhaps a firmware upgrade would unlock these 'hidden' features.

@oldestgamer 2 жыл бұрын

This looks like the typical "toy" scopes I had been seeing when looking for an inexpensive but usable portable scopes for our bioengineering students to use at home for the electronics labs during covid. Virtually every one of them were just crap, until we found the Fnirsi-1013D 2-channel tablet scope. The Fnirsi, at around $130, is a VERY usable scope, with two channel display, touch screen at around 7" and usable up to around 20 MHz, although they claim 100 MHz. Come with two probes and the battery has good run time and yet there is plenty of room for a larger and longer lasting battery. I was so impressed that I, along with another professor, bought one to use in our home labs. THIS is what you should do a review on, it would smoke that Hantek. The Fnirsi scope is also sold under a variety of names, but are all the same, basically a 7" tablet, touch-screen scope. People, check it out and stay away from these tiny screen "toy" scopes if you want to do real work, those rinky-dink scopes are a waste of time and money.

@Quickened1 2 жыл бұрын

Except, the cheapest I see them on Ebay is $170... :(

@oldestgamer 2 жыл бұрын

@@Quickened1 got them from aliexpress

@nickdaniels5892 2 жыл бұрын

We get right to it. That's what we do. Dont mess with the order 😁

@rimmersbryggeri Жыл бұрын

I think the clip leads are for the signal gen. that might also be the difference betwen c and d.

@ericvenneker 2 жыл бұрын

Thanks for the great review! And if this was reviewed by either Dave Jones or big Clive it is either hot garbage or the best thing ever since sliced bread!

@konstantinjirecek970 Жыл бұрын

There is 1kHz square calibration signal for oscilloscope probes on third connector even on models that do not contain signal generator.

@francoismontigny5987 2 жыл бұрын

Normally you can also use this device with a PC, for long capture data. I did on my Hanteck 2D92. With the software It has a possibility to save data, but need the score to read it out. It cannot be read alone directly on PC.

@Colaholiker 2 жыл бұрын

Grounding via USB can be an issue going the other way as well. When I put together my small microcontroller projects, I often connect them to my PC using a USB to UART cable that also supplies power to the board. So far, so good... until one day I wanted to measure a signal with my mains powered scope. Touching the board and the ground clip of the scope at the same time when I tried to connect the scope to the powered board gave me a small shock. It took a while for me to find out what happened. The outlet that the scope was powered from was one that I installed myself, it had proper grounding. The one that powered the PC was an outlet that was already there... and (breaking several electrical codes) was not grounded at all. So everything on the PC that should be connected to earth/ground was actually floating on a level defined by the input filter caps. The scope then gave the bridge to ground.. ouch. @Adrian Another nice tool for your retro repairs could be a small logic analyzer. For the speed you encounter there, one of the inexpensive "LA-1010" models may be something work looking into. I am using mine a lot, this thing was money well spent.

@jean-lucpicard8186 2 жыл бұрын

He already has a logic analyzer, he just doesn't use it much anymore because it's not as entertaining to watch.

@Colaholiker 2 жыл бұрын

@@jean-lucpicard8186 Oh, I didn't know that Adrian's digital Basement is also watched on the bridge of the Enterprise... ;-) Jokes aside, I don't recall ever seeing him use a logic analyzer beyond his single logic beepy probe. But I may have just forgotten about that.

@jean-lucpicard8186 2 жыл бұрын

@@Colaholiker Yes indeed, he is a particular favorite with Lieutenant LeForge and Commander Data. They are fascinated with and impressed by the fact that someone from such an already ancient time as 2022 would be preserving technology that was already so old and outdated even then. :) Jokes aside, I don’t remember seeing it much either, I think he quickly realized that it wasn’t very much fun to watch compared to stuff on the oscilloscope. And yes, I was counting the “single logic beepy probe” as his logic analyzer, my apologies if that isn’t the proper name for that tool.

@Colaholiker 2 жыл бұрын

@@jean-lucpicard8186 No need to apologize when talking about technology from long gone times and not getting the terminology 100% straight, Captain! :o) At least during my time, we used to call those "logic probes", while logic analyzers were monitoring several channels at once, for example to analyze the data bus and see what bytes are going through there.

@jean-lucpicard8186 2 жыл бұрын

@@Colaholiker Interesting, I’ll have to see about getting one of those replicated as a gift for their work. They are currently trying to figure out how to procure one of these “Commodore 64” computers, and that tool might prove useful for diagnostic work. The biggest issue at the moment is procuring one that DOESN’T work so they can enjoy the troubleshooting process, as the initial thought of “just replicate one” would produce a fully working specimen, and remove some of the enjoyment.

@imqqmi Жыл бұрын

34:00 it could also be the tri state function, when the cpu and all other devices are in high z mode, the voltage just wanders a bit.

@diydsolar Жыл бұрын

Hi, thanks a lot for the video. Is this oscilloscope valid to see the wave form of a 230VAC grid or inverter signal? If not, could I use a 230/48 transformer and the 10x? Does the transforme "smooth/disturb/...." the signal? Do you have any video about how to see this signal to chekc modified, pure sine, armonics, .... Thanks

@tiporari 2 жыл бұрын

I like the scope.

@johnkrakovsky7311 Жыл бұрын

I only use the Hantek for the Function Generator. So far, this is the cheapest battery-operated function generator that doesn't require a computer that I can find. The main problems I see for this unit is you always need to run the O'scope self-calibration before measurement & if you leave it sitting for a month, the battery will be dead. For cheap O'scopes & Arb Generators, I prefer Siglent.

@dananorth895 Жыл бұрын

If it has the hardware present for the function gen. I wonder if there's a hack like in computer bios's were you tweak/set all the goodies on the board. I kinda doubt an interior resistor/lead etc.

@wiedapp Жыл бұрын

These things, are excellent for field techs. OWON has a similar one. I want to see the tech guy/girl lugging around his expensive HP bench top oscilloscope for field use. Some things you can't get to the workbench for troubleshooting.

@ropersonline 2 жыл бұрын

Since I'm not sure I caught that in the video: Can this $125 scope also, as an alternative to using its little screen, be connected to a laptop just like the $60 Hantek? (You did show the software briefly, but I'm not sure which scope that was.)

@aetch77 2 жыл бұрын

Short answer is yes but I wouldn't. Just like the Hantek supplied software for the $60 model, it's horrendous. Also, I don't believe 3rd party software exists for the 2xx2 range (I would love it for my 2D42).