TESTING THE JET JON BOAT

No video

TESTING THE JET JON BOAT - We Drag Raced

Рет қаралды 116,437

4 жыл бұрын

HOW TO VIDEO LINKS:
How to Gap Piston Rings - • How to Gap Piston Ring...
How to Check PTV Clearance - • How to Check PTV Clear...
How to Measure Bearing Clearance - • Measuring Bearing Clea...
How to Measure Pushrod Length - • How to Measure LS Push...
--------------------------------------------
WHERE I WORK:
www.smedingperformance.com
@smedingperformance
--------------------------------------------
MOTOVLOG EQUIPMENT:
GoPro: amzn.to/3HUKn7U
Media Mod: amzn.to/3xhxJLk
Mic: amzn.to/3E44Fe7
Volume Control: amzn.to/3DWqnRe
--------------------------------------------
GENERAL FILMING EQUIPMENT:
Camera: amzn.to/3Ymtw4V
Accessory Kit: amzn.to/3DZRY43
Wireless Mic: amzn.to/3IgM0hA
Lavalier Mic: amzn.to/3HUN4Gy
Micro SD Card: amzn.to/3JZTLd6
--------------------------------------------
DISCLAIMERS:
All videos are filmed in Mexico with trained professionals, unless stated otherwise.
All content posted under this domain has no affiliation with its poster and any relation to the rider portrayed in any way which it includes. The rider is not limited to his or her likeness, location, or personal identity.

Пікірлер: 45

@explorster 3 жыл бұрын

Another awesome video Kevin.

@ripptydevibes2581 4 жыл бұрын

Awesome man!! I just got done my 16' seado 787 110hp if your interested in any build vids theyre up!

@garrettsmith6237 4 жыл бұрын

Sweet build! I love canyon lake too 👍🏻

@jamessladek4794 3 жыл бұрын

Love it boys !! Minty as all hell

@purehonda23 3 жыл бұрын

Exactly why I'm building mine with an arcticcat THUNDERCAT 900 TRIPPLE direct drive to a chopper prop.. Guarentee a 30 horse outboard isn't beating me 😂

@sharonbraselton3135 3 ай бұрын

Master chef herd it 3 jet 3. Bunk beds inncabin

@jasonhodgws5266 4 жыл бұрын

I had the same idea but in the bow slighty foward a midsship. With an out board aswell. Jet drive For striking net so i can just run it over and have no problem.

@russrogers3106 10 ай бұрын

I have that same little Yamaha... Great motors!

@kellstat Жыл бұрын

7.3 90's Bronco! That sounds like a winning swap! Nice build.

@caesar1295 Жыл бұрын

Is that the OJ Simpson bronco?😂😂

@CncObsession 4 жыл бұрын

Any problem actually registering it? I want one for Lake Whitney

@ujtchanel3157 3 жыл бұрын

Good job very fast

@ARno15 4 жыл бұрын

How is an outboard smokin u?

@Samisasleep1420 2 жыл бұрын

Haha that my welding rig 👌

@chrisklassen3217 2 жыл бұрын

Is there a link to the video of building the boat?

@TBassFactory 4 жыл бұрын

I have made that same run up canyon so many times in my 15 ft 900 zxi jet Jon. Looks like you guys built yours just like mine for the most part, looks good.

@sharonbraselton3135 3 ай бұрын

Master chef pollycradt 4.8. 90 hp jetoutvard csbin crusrr

@markeiler9753 Жыл бұрын

I want to build one these. I think I should get a better welder.

@Judge_Judy 3 жыл бұрын

how shallow can it go ?

@trainbobber03 4 жыл бұрын

How bout pop rivets?

@jonroberts6518 2 жыл бұрын

Was bout ask how long are the boats , already have a 10ft since I was little, just think it's to small , to do what I want with it . think I would go around 16'-20' for the jet john I'm looking to build.

@sharonbraselton3135 3 ай бұрын

Evolution 52 150 hp jet or trained 20 150 hop jet 20 f I t searayray dundacer. Cabin crser 16 f I t 20 foot cabjn cryserr jet drhve

@edwardvargas1036 4 жыл бұрын

Y’all from Texas

@deck1960 4 жыл бұрын

I see you recessed the drive into the hull of the boat --- I have also seen it where it is mounted directly on the back without being recessed inside why did you decided to do that

@trevorbaldwin6063 4 жыл бұрын

Dennis Eckmann just wanted to protect it some. Without the recess it would stick out almost 16” . It’s just a few 1/4 bolts going into aluminum holding it together didn’t want any strain on it if we went over a log or something. I also plan on building aluminum tubing around it at some point to protect it further

@drdraws9597 4 жыл бұрын

If you flush mount it you need pods

@Raygilley10 3 жыл бұрын

is that oj simpsons old bronco

@dakotadriggers8838 4 жыл бұрын

That place is gorgeous, where is it?

@JacobVillemain 4 жыл бұрын

Canyon Lake, TX

@colbymcghee9693 4 жыл бұрын

Rebecca creek

@roberthealy2172 4 жыл бұрын

Was that the Demolitia truck with that welder?

@JacobVillemain 4 жыл бұрын

Robert Healy Negative

@GapCracker Ай бұрын

You had zero penetration on some of those pieces. Do a quick search on here, idk what your settings are but doesnt look hot enough and wrong angle of attack. Might be better off with rivets in some of those spots. Welding aluminum is not easy like steel and most people don't realize it so at least it held up as well as it did.