Love hearing your stories on these vintage saws. Would like to see you do 1/2hr + videos on old saws and talk about how they cut compared to others, if they were reliable or what failed etc etc. Basically like this video but longer with more stories.
@cfletch852 жыл бұрын
I just found one of these in my garage attic from the previous homeowners.
@henryjack98704 жыл бұрын
wow...I still use my homelite 360 on a weekly basis...i was having bogging issues at top end...i ended up resetting my high low and idle screws...i ended up setting my high and low screws 1 full turn out from seated and works perfectly now
@cobhc19865 жыл бұрын
Thank you! I have a nice 360 that I just got done replacing the intake boot and crank seals on. It felt kinda slow to me when I was testing it but the one in this video seems to be running the same, so I'm guessing it's normal for those.
@joerehwinkel648 Жыл бұрын
I need a 24 inch replacement bar for my 360 homelite
@WestCoastMuscleSaws Жыл бұрын
The small mount bar for Husqvarna works with minimal mod Joe. WestCoastMuscleSaws TheChainSawGuy Rich kzfaq.info
@roadking83377 жыл бұрын
do one on homelite 410 I have 2. still use them
@deeman50764 жыл бұрын
I seen one a couple years ago just when i was getting into powersaws did some research found its a 70cc saw?
@KennethHanfordSr5 жыл бұрын
Where can I find a coil or acceptable replace t coil for this saw. I have one and loved it when it ran.
@hibbityhoobla66247 жыл бұрын
just bought a 360 at yard sale ten bucks. guy said pull rope broke which it did took it apart replaced rope but now having trouble figuring out which way to wind it up. not the coil but the rope. any thoughts or maybe a video?
@thewilddinkus80265 жыл бұрын
Take the side panel off of the flywheel then spin the shaft that is hooked to the coil around or pre wrap the rope then install it
@remingtonsawdust80466 жыл бұрын
Which model bar and chain? I can't find an Oregon replacement. What chain would you recommend for a 24" bar, if I can find one. Thank you!
@mikecubes16425 жыл бұрын
look at a site called cutters choice www.cutterschoice.com/ShopFrontPage
@Monsterbootsmoto7 жыл бұрын
Has anyone found a source for the intake boots that always rip, I've got a few homesites that are in good shape other than the deteriorated boot
@mr.homelite84907 жыл бұрын
The intake boot,the chain guy has some or they are on ebay.
@budrip97285 жыл бұрын
I just cleaned the one i have the night im watching this
@benjaminpainter3785 жыл бұрын
That's exactly what I'm doing right now hahah
@louismorel2001 Жыл бұрын
Hello Nice vidéo thanks Can i ask you what is the bar do you it on the 360? Does it suit it stock or do you have to fit it ? Modifying oiling holes etc? Thanks a lot Louis
@WestCoastMuscleSaws Жыл бұрын
The small mount Husqvarna bar is a very close fit. Reference a Husqvarna 359 model when ordering. Take Care Louis, WestCoastMuscleSaws TheChainSawGuy Rich
My dad has this saw and LOVES it! Recently, it began gushing oil when running. What's more, it's NOT lubing the chain. He'd like to repair it, but we don't know where to start. If it WASN'T pumping, I'd say it's the pump. Any advice appreciated.
@AIRPORT-mc2ys Жыл бұрын
exhaust wraps around TWO SIDES of cylinder causing overheating. MAD IGNITION blocks other 2 SIDES. poor oil delivery BURNS UP CHAINS & BARS, DESIGNED IN rubbish intake boot causes OVERHEATING as it cracks= DESIGNED TO FAIL = lots of money to DEALER