The front wheel hub cross broke while the excavator was digging and I expertly repaired it

Рет қаралды 122,557

CNC Master1

16 күн бұрын

Пікірлер: 34

@Tatal.b 5 күн бұрын

Belo trabalho gostei, ficou.muito bem feito 👏👏👏👏👏

@juancarlosmiranda2736 10 күн бұрын

MARAVILLOSO - FELICITACIONES!!!

@elkincondechincha5753 5 күн бұрын

That piece now has more strength than the original piece.

@martinleska4292 9 күн бұрын

From mechanical and machinery skills looks great, but I hope they didnt expect long term reliability. Someone broke 1,5cm of metal on each side plobably from metal fatigue but after repair it held only by tiny pipe and shallow porous welds. In this case threads doesnt hold any forces, only positioning and centering parts with small play because this threads are not tapered or hard tightened to the other part.

@adailtoncamposrochacamposr8759 9 күн бұрын

Sensacional, parabéns! Melhor impossível!

@robertwilder4425 3 күн бұрын

nice job . un trabajo con cálidad

@johnj4130 14 күн бұрын

Very good repair, but you should have welded the big ring on the inside as well as the outside.

@tengkuabasshahtengkuamansh7677 14 күн бұрын

CNC Master 1 KZfaq channel the best from Pakistan and the world ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤

@vaclavmartinek6932 7 күн бұрын

U zz mil

@ungerspretoria8280 10 күн бұрын

The threads are loose fitting, this tiny movement will cause metal fatigue on the entire hub, Will break again in a week or two...

@robertwilder4425 3 күн бұрын

you don't know what are you talk about this job never going to broke

@gordonagent7037 Күн бұрын

Sir, very well done. To be a machinist you have to be able to think outside the box when it comes to finding a suitable and safe solution. I think you did an awesome job of machinery here and I’m sure that it will outlast the truck as your threads were well cut and were a snug fit and the welds had plenty of penetration. Congratulations sir, a very competent repair.

@AlbertoMartinez-gz3ch 14 күн бұрын

Me gustan sus videos pero lo que no me gusta es que inician casi con un minuto del vídeo y luego se regresan y vuelven a empezar 🤔🤔 háganlo bien desde el empiezo y no así ok? Saludos de México 😊

@keithameerali9474 12 күн бұрын

It is called a preview.

@user-dr2xp4yv2z 10 күн бұрын

Я хоть и не токарь а работаю фрезеровщиком по металлу, впервые вижу что чугун варят со сталью.😂

@user-ll3lj1xp7w 9 күн бұрын

Что ты хотел, если тут самый точный инструмент - штангель 🤣На станке варим, ваще поую 🙆‍♂🤦‍♂

@robinstan5810 8 күн бұрын

that black paint does all the job

@user-ek6bn4zb2d 3 күн бұрын

Как хорошо станок закручивае за одежду лахманы

@U.F.O.Technology 14 күн бұрын

How much does turning work cost?😊

@victormontecinos3755 9 күн бұрын

Se paso cuanto vale ese trabajo en dolares.perfecto.

@freshhealthy8118 14 күн бұрын

❤❤❤❤

@alcotanflorperez4109 12 күн бұрын

Estos trabajadores son fantásticos, tienen soluciones para todo, mis respetos 👍👍👍👍

@EmilioCoppini-gx4rf 14 күн бұрын

You are very able,good.From Italy.

@PeterChapman-rg6gr 13 күн бұрын

We start off with a broken CAST IRON housing. It is then threaded and a very loose fitting steel insert is screwed in. This is then welded with 1 run of "Pac Bridge" 6013 welding rod. Note no pre heating, post weld controlled cooling or even the correct welding rods for cast Iron to Steel welding. This weld would have cracked at the casting when it had cooled down. The exact same applies to the steel plate that was very loosely screwed into the other part of the Cast Iron casting. Again welded with 1 run of the ubiquitous "Pack Bridge" 6013 welding rod. This is yet another in a very long line of pure "Click Bait" videos with a bodged "Repair" that will never be fitted to any vehicle

@arthurmario5996 12 күн бұрын

IDK, maybe they just sell it, so it's not their problem? Also, many heavy machinery and railroad parts are cast steel, which is more expensive, but can be welded. they def did not make enough passes tho. ps: i am not a welder, so...

@SubramaniamLakshminarayanan 11 күн бұрын

What better did you expect from a Pakistani mechanic?

@SubramaniamLakshminarayanan 11 күн бұрын

@@arthurmario5996 - any weld is a compromise as compared to the strength of an original part. If a 30 or 40 mm shaft can break on load, do you think a generous 10 mm weld will hold and give the same performance??

@arthurmario5996 11 күн бұрын

@@SubramaniamLakshminarayanan of course not

@vintagerecordambassadeur4098 10 күн бұрын

They did this exact repair for me 3 yrs ago and it’s still holding fine. Perfect