How to Re-gear a Dana 30

  Рет қаралды 171,130

The BFH Garage

The BFH Garage

3 жыл бұрын

Disclaimer: The following disclaimer applies to The BFH Garage KZfaq channel (referred to as "the Channel"). By accessing or using the Channel, you acknowledge and agree to the terms and conditions of this disclaimer. If you do not agree with these terms, please refrain from accessing or viewing the Channel.
Content: The Channel provides automotive-related content, including but not limited to repair guides, maintenance tips, product reviews, and general information. The information presented on the Channel is based on the personal opinions and experiences of the Channel's creator and contributors. However, the Channel makes no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability, or availability of the information, products, or services mentioned. The content is provided for informational and entertainment purposes only and should not be considered professional advice.
Personal Responsibility: The Channel encourages responsible automotive practices. However, any actions or decisions you take based on the information provided on the Channel are solely your responsibility. The Channel cannot be held liable for any damages, injuries, or losses that may occur as a result of following or implementing any information or advice presented on the Channel. Always exercise caution, consult professionals, and adhere to safety guidelines when working on or modifying vehicles.
Third-Party Content and Links: The Channel may include links to third-party websites, products, or services. These links are provided for convenience and informational purposes only. The Channel does not endorse or have control over the content, products, or services offered by third parties. Accessing or using third-party content is at your own risk, and the Channel shall not be responsible for any damages, losses, or issues arising from such content.
Intellectual Property: All intellectual property rights, including copyrights, trademarks, and any other proprietary rights, in and to the Channel's content (including videos, images, graphics, logos, and text) are owned by or licensed to the Channel. You may not reproduce, distribute, modify, display, perform, or otherwise use any content from the Channel without obtaining prior written consent from the Channel.
Changes to the Disclaimer: The Channel reserves the right to modify, update, or change this disclaimer at any time without prior notice. It is your responsibility to review this disclaimer periodically for any changes. Your continued use of the Channel after modifications to this disclaimer will constitute your acknowledgment and acceptance of the modified terms.
Governing Law: This disclaimer shall be governed by and construed in accordance with the laws of the jurisdiction in which the Channel operates. Any disputes arising out of or in connection with this disclaimer shall be subject to the exclusive jurisdiction of the courts in that jurisdiction.
If you have any questions or concerns regarding this disclaimer, please contact us through the appropriate channels provided on the Channel.
Last updated: May 11, 2023

Пікірлер: 290
@rockyjones9956
@rockyjones9956 3 жыл бұрын
One of the best and most professional gear set-up videos I have seen. Great job.
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Thanks for the comment!
@ahmadkamali8547
@ahmadkamali8547 2 жыл бұрын
Yesss a real professional knoldge
@TheBFHGarage
@TheBFHGarage Жыл бұрын
😂
@edwingonzalez6060
@edwingonzalez6060 3 жыл бұрын
This has been one of the best videos about regear that i have seen
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
I'll be adding more re-gear videos in the future to provide different perspective.
@edwingonzalez6060
@edwingonzalez6060 3 жыл бұрын
@@TheBFHGarage it de would be awesome if you make like a complete tutorial breaking down all the steps by parts
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
@@edwingonzalez6060 I intend to do that for a future video!
@edwingonzalez6060
@edwingonzalez6060 3 жыл бұрын
@@TheBFHGarage thanks a lot, i am planning into rebuilding an ected max locker of a jk, will keep the contact to watch it.
@shaneshaw1895
@shaneshaw1895 2 жыл бұрын
I've watched a dozen videos trying to find the proper way to set up the pinion depth and preload and this is by for the most comprehensive instruction I've found, thank you.
@dad3562
@dad3562 Жыл бұрын
Did you ever give it a go on your own?
@joecockey6942
@joecockey6942 Жыл бұрын
Thanks! Did my first gear change 3.07 to 4.10! Took my time; very happy with results. Thanks for your many great vids!
@johnathandoe3558
@johnathandoe3558 6 ай бұрын
Very good teacher. The level of depth you go into is great. Really appreciate the videos. Thank you
@douglasphillips24
@douglasphillips24 3 жыл бұрын
Excellent content . I can tell this ain't this Man's first rodeo. Thank you for the PVC pipe trick to install seals. This man definitely explains the R& R of a ring & pinion set-up for those with Common sense to understand unlike some who make this job more complicated via marking & measuring every single tooth of the ring gear which is overkill in my opinion. Thanks for keeping it simple Brother. God Bless.
@codylee5132
@codylee5132 Жыл бұрын
Excellent video sir. Definitely the most information gear setup video I’ve seen on KZfaq.
@jamescody964
@jamescody964 5 ай бұрын
I've been fighting this dana 30 all day. I'm so glad I came across this video! Hands down the best instructional video I've seen on this subject! Great job, and thank you!!
@iflytango
@iflytango 3 жыл бұрын
Excellent explanation on install process especially about how the crush sleeve works
@jbhk7977
@jbhk7977 2 жыл бұрын
Very detailed and step by step tutorial. Thanks for the awesome video mate.
@warrenfromga9945
@warrenfromga9945 Жыл бұрын
Thank you for you detailed dialog for this process. Your explanation and presentation is the most helpful for this amateur DIYer that I have been able to find. Thank you.
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Glad it helped out!
@BTBLive
@BTBLive Жыл бұрын
Honestly, this is the best gear setup vid on KZfaq. Thank you
@platonpanagopoulos73
@platonpanagopoulos73 2 ай бұрын
Really great, professional , detailed and informative - 10/10!!!
@donalddeveau6423
@donalddeveau6423 Жыл бұрын
This was the best instruction video i have ever watched , thanks for doing it .
@petemiller519
@petemiller519 3 жыл бұрын
Super video. Can't wait to build my house so I can build my shop, so I can re-gear my JK. 2:00 in the morning, gotta go to bed so I can finish the excavation tomorrow. I hope I won't drop dead before I can finish my JK.. Cheers from Canada!
@chrisclark3503
@chrisclark3503 Жыл бұрын
Awesome job man! You make some outstanding videos, Thanks for your effort, huge help!
@Tony-hg9kc
@Tony-hg9kc 2 жыл бұрын
Watching you do this is like watching a master chief prepare fine food. You’re set there and how clean it is , Absolutely impressive
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
Thank you for the kind words!
@Joes-Adventures71
@Joes-Adventures71 Жыл бұрын
By far the best videos on gear setup.
@markbutler6634
@markbutler6634 Жыл бұрын
The best Video by far on ring and pinion set-up, thanks. I am installing a yukon locker and gears in a D-30 also, this is my first time in side a diff other than changing gear oil and swaping out axles. I feel more confident having watched this video for sure.
@framerandy77
@framerandy77 3 жыл бұрын
Wow, when it comes to gears and axels you're a badass. This video helped me out with this so much. Thanks!
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Thanks for the compliment!
@MarkMcArthey
@MarkMcArthey 3 жыл бұрын
I really would love to do this myself as I find it fascinating and your video is the best I’ve seen for showing what I could expect. I need a friend like you to help out lol. Thanks much for a great video!
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Thanks for the kind words and good luck with it!
@josemariaresendesilva6105
@josemariaresendesilva6105 2 жыл бұрын
Incrivél, exelente video, clear explanations in pinion adjustments. I'm resreforming the differential of my Jeepster 1946 I found myself in the dark, with his explanations I found a lucid light in front of me. Congratulations on the content. Sorry some text errors, I'm Brazilian ...
@wranglerlife4ever42
@wranglerlife4ever42 2 жыл бұрын
I would not hesitate to have this guy work on my Wrangler JK. His attention to detail, workmanship and professionalism is top notch.
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
Thanks for the kind words👍
@tmackinator
@tmackinator Жыл бұрын
This is a proper set up video. This is the way to do it. Nice job!
@berryae74
@berryae74 Жыл бұрын
Excellent video! Best I've seen bar none..
@bmaxTJ
@bmaxTJ 4 ай бұрын
Very informative. Thank you.
@MrSrtman18
@MrSrtman18 Жыл бұрын
Good stuff here! Thanks for the tutorial and the time!
@lukekolodziej9631
@lukekolodziej9631 3 жыл бұрын
Very well done video, thanks for all those tips!
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Thanks for the compliment, I'm glad it helped you out!
@SpooxyCowboy1911
@SpooxyCowboy1911 Жыл бұрын
I don’t plan on doing my own regear but this is super informative and explains why regearing in California cost 3k
@Bdady74
@Bdady74 2 жыл бұрын
Very informative, great video!
@sterling6860
@sterling6860 2 жыл бұрын
I have built a lot off diffs on both cars and trucks,,But I have learnt a good few tips from this video,,Great stuff.
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
Thanks for the kind words! Glad it helps👍
@KN-sd9lt
@KN-sd9lt Жыл бұрын
Thank you for sharing your knowledge brother! This video helped me out alot!
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Glad to hear it helped!
@chukchee
@chukchee 2 жыл бұрын
Awesome job and video!
@beckcameron9297
@beckcameron9297 2 жыл бұрын
This might be the best how to automotive video I have ever seen, I wish you worked on land cruisers!
@Nuthinseasy1
@Nuthinseasy1 3 жыл бұрын
Great video! Thank you!
@stevenjames7073
@stevenjames7073 2 жыл бұрын
Thank u for sharing …very nice explanation👍
@RegularJohntv
@RegularJohntv Жыл бұрын
Thanks for sharing all that. It was a lot but I think I got it. 👍 answered a lot of questions
@larryfischer364
@larryfischer364 4 ай бұрын
By far one of the best videos I have seen , you've obviously been doing this for a while, I've probably set up around 500 rears over the past 20 years myself , Does that M-18 impact have the power to crush GM 12 bolt or mid year corvette 10 bolts,.? I still crush these with a 3/4 breaker bar with a 3 ft pipe extension . Recently have run into crush collars that won't crush period . [ after market ] I laugh at some of these other you tube rear set-up videos , No carrier preloads ,poor patterns etc.
@dj-sniper-q8398
@dj-sniper-q8398 2 жыл бұрын
Excellent job, nice explanation, thank you...👍👍👍😍😍😍
@ryanj9731
@ryanj9731 2 жыл бұрын
Very informative & knowledgeable mate, good thorough vid, thanks!
@ryanj9731
@ryanj9731 2 жыл бұрын
Do you think a Dana 30 would survive 35's air locked, decent wheeling roughly once a month 🥲
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
I beat the crap out if mine on 35's locked. It will be fine. Get some chromoly shafts though.
@ryanj9731
@ryanj9731 2 жыл бұрын
Right ok, wicked...alot better to hear than an axle upgrade..cheers mate, Il look into the chromolys 👍
@Thundarr995
@Thundarr995 2 жыл бұрын
I always ditch the crush sleeve and install a solid spacer and shim kit instead. It's really easy to crush the sleeve too much,then you have to get a new one. Idk how much you have to tighten the Dana 30 to start crushing the sleeve. Last one I rebuilt was a GM 7.6 out of a 97 S-10. Took about 400 ft/lbs to crush it. And then it crushed it too much so my pinion bearing preload was too much. Then I found out that you can use a solid spacer and shims instead of the crush sleeve. It really works great and you only need to tighten it to 125 ft/lbs. And there's no crush sleeve in there that may keep crushing over time and screw up the preload. Reyteck makes the solid spacer/shim kit.
@2S1L3NT
@2S1L3NT 3 жыл бұрын
Awesome video! Helped me decide to pay someone else to do it for me... 😂 Unfortunately I definitely don't have any of those test races and nuts and extra tools needed to do this job in my driveway. But I need to research who's reputable. Thankfully I live in Utah so there should be plenty of them...
@shozdott
@shozdott 4 ай бұрын
wow man such good tips ty
@Pseud0rand0m
@Pseud0rand0m 2 жыл бұрын
Great video. Thank you
@xuv5607
@xuv5607 2 жыл бұрын
OUTSTANDING EXPLANATION!!
@marvinboris145
@marvinboris145 Жыл бұрын
Excellent Video 5 Stars 👍
@marcellopasini
@marcellopasini 2 жыл бұрын
Great video!!!
@roadmound429
@roadmound429 Жыл бұрын
Excellent video 👌👌
@dylanmacias1288
@dylanmacias1288 3 жыл бұрын
great vid, thank you for this
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Glad you like it!
@lenchintachin8188
@lenchintachin8188 2 жыл бұрын
Que buen video mi conpa.....muchas gracias por conpartir....
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
!Me alegro de que haya ayudado!
@aditparikh781
@aditparikh781 2 жыл бұрын
Nice around halfway through this video I realize I’m going to take my jeep to the shop
@samsavill8513
@samsavill8513 3 жыл бұрын
Great video, I learned a lot. Enough to know to leave my regearing and LSD install to someone with better skills and proper tools.
@ixlr8677
@ixlr8677 3 жыл бұрын
all it takes is common sense and proper tools. enough common sense u can make your own tools. oh if you tackle a 400 turbo bread sacks works best for clutch seal instalation.
@robertmyers6763
@robertmyers6763 2 жыл бұрын
Wow that really clears up a lot. Probably the most informative video I have ever seen.
@randygebhart6560
@randygebhart6560 Жыл бұрын
I couldn't get my pinion gear out, tried prying and tapping on it to shake it loose. Thanks for the wrench trick!
@tonycamarato4582
@tonycamarato4582 5 ай бұрын
You explain things with great detail and camera work is at just the right angles! I watched this and your Dana 44 videos-Trying to figure out how to re-gear to 4:10. Can we re-use the axle shafts with the different gearing on the front and rear?
@sts.556
@sts.556 Жыл бұрын
very good video thanks
@Jeff-kp3jm
@Jeff-kp3jm 6 ай бұрын
Thank you, Peter Weller! This was very helpful! I know you’re not Peter, but you could be mistaken for him hahah
@kailiannsadeski6906
@kailiannsadeski6906 2 жыл бұрын
Fantastic video! Appreciate you taking the time to show us how it's done. Question, maybe I missed your explanation: what's the size difference between your setup race and actual race? Want to have one myself for my regear but not sure what I should be looking for
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
So a setup race is the exact same as the new race with one exception. The new race has to be driven in with a driver. A setup race slides in and out with minimal resistance. I take a Dremel with a sanding drum and sand down the outside of the race until it just fits without having to be driven in. You should also be able to pull it out by hand. Don't make it too loose or it can throw things off. Be sure to use the same brand race as what you are going to install to keep errors to a minimum.
@Blastfence1
@Blastfence1 2 жыл бұрын
Excellent!
@manuelsolano7525
@manuelsolano7525 3 жыл бұрын
Excelente muchisima grasias.
@tarewade9681
@tarewade9681 2 жыл бұрын
Great video. Thanks, after watching several videos, some more than once, I'm wanting to give it a try rebuilding my AMC 20 myself. It's got quite a few miles on it, and still works fine, but seals leak, and the back lash is excessive from wear. Maybe about a quarter inch of slop twisting the yoke back and forth. Judging from that kind of slop, do you think I could re-use the gears, just replacing the bearings and seals, and it would be ok?
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
I'm not a fan of reusing gears. They are very difficult to set up. Now if you are just changing bearings and seals, you shouldn't have to change anything else and you should be ok.
@Gearsandoil
@Gearsandoil 2 жыл бұрын
Great video! I’ve watched I think 3 times! One question, how do you torque the ring gear bolts? With the carrier in a vice or something to hold it steady or with the carrier assembly back in the vehicle?
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
You can do it couple of ways. You can put it in a vice before pressing on bearings or you can torque then the first time you install. I would torque before running any patterns to make sure it's set.
@bobyaheadtothemarley
@bobyaheadtothemarley 3 жыл бұрын
Incredible video! Thank you. Trying to learn and pump myself up because I have to replace the Trac-Loc in my 86 Dana 44 rear. Question for you guys. If I get a Dana Open Carrier, can I re-use my gears? R/P or Spider? Or should I plan to replace everything? Any "okay" ways to save some cash? My trac-loc clutch pads separated and have worn out the housing, Jeep drives fine but i think it's a ticking time bomb. Also where is your shop located? Searched for BFH but couldn't find it.
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Yes you can just replace the carrier and reinstall. Make sure you get the right carrier for the gears you have. They have a carrier "break" depending on your gear ratio. Be sure to keep shims on the side they came out of if you reuse your gears. Check backlash before and after to make sure you're good to go.
@johndelta00
@johndelta00 3 жыл бұрын
Good job! I would've sent it with the first pattern you got.
@mrfudgierubber
@mrfudgierubber 6 ай бұрын
Brilliant video as always, thank you. I know diff temperature can be more than thread lock specs , which one do you use? I thinking of drilling and lock wiring my bolts.
@TheBFHGarage
@TheBFHGarage 6 ай бұрын
Red loctite has never let me down 👍 I think drilling and wire is not necessary. On the old first gen three piece ARB it was needed, but not now.
@spelunkerd
@spelunkerd Жыл бұрын
This video clarified a lot of issues I wondered about through the years, it's the best video on the topic I've ever found. I notice you shimmed behind the bearing race to move the pinion toward the rear, to bring the paint pattern into spec. Just after 17:10 you mentioned that you were going to take a risk by pressing the new bearing onto the pinion, guessing that no more shims would be needed there. What sign on the paint pattern would prompt you to take off the gear to add or remove extra shim there? What do you think about the method of sanding the old bearings down so they come off easily, adjusting shims to get contact patterns into spec, then install the new bearings and shims with more confidence that you won't need to remove bearings again?
@TheBFHGarage
@TheBFHGarage Жыл бұрын
So in that video, me taking a chance was before I had a clamshell bearing puller. Meaning if I was wrong, that would have sucked as there isn't a "good" way to pull the bearing if I was wrong. Even bearing "splitters" can cause damage. As far as sanding down a bearing, I'm all for that EXCEPT that you don't want to use an old bearing. You want to use a NEW bearing. Old ones have too much play and will create a pattern that will be different from final setup. I can't stress how frustrating that is. As far as reading patterns, it's kind of an art in a sense. I'll try to do a video on that some day👍
@gatordave6629
@gatordave6629 2 жыл бұрын
When you went to put that pinion back in the second time how did you get a .003 thousands measurement on your shim
@sinanalobaydi3442
@sinanalobaydi3442 3 жыл бұрын
thankyou Sir
@declanpatricko
@declanpatricko 2 жыл бұрын
Wow you think this guy has done this before or what. Absolute expert level.
@markremillard5135
@markremillard5135 3 жыл бұрын
Damn you're good
@1freetuck
@1freetuck 8 ай бұрын
I got it thanks to you! But pinion nut seal all done great. Preload but I forgot to put oil baffle behind pinion seal. What should I do?
@1freetuck
@1freetuck 8 ай бұрын
All done I put a new seal and nut.
@josearguello6989
@josearguello6989 3 жыл бұрын
Awesome video! Trying to learn to do my own regear. Are the shims in a stock open carrier on the inside of the bearings or are they all on the outside like that?
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Depends on which axle. On the Dana 30 in a TJ, if it's an open carrier they go under the bearings most of the time. And I only say that because most of them have master shims that go to the outside. I would recommend looking at the factory service manual for your specific model. The Rubicon model has shims that go to the outside. ARB air lockers place the shims to the outside.
@flaparoundfpv8632
@flaparoundfpv8632 3 жыл бұрын
@@TheBFHGarage My XJ's Dana 30 has them on the inside, but I screwed up and pressed my new bearings on, thinking they would go on the outside. Would I be running any risks if I put them on the outside? Could they work themselves out of place?
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Do you have thicker OEM master shims that were on the outside or only thinner shims between the bearing and carrier?
@InvictusOffRoading
@InvictusOffRoading 2 жыл бұрын
Bro, this was deceivingly easy in some parts
@kevwtfo6508
@kevwtfo6508 2 жыл бұрын
Outstanding video! Did you set the pinion depth to a pinion depth stamped on the end of the pinion? I ask because many sources say that is the first step then fix lash by adjusting ring gear shims. Please help me understand.
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
I don't ever look at what is on the head of the pinion simply for the fact it is quicker to use the existing pinion depth shim to start. Either way you're most likely going to have to make adjustments.
@kevwtfo6508
@kevwtfo6508 2 жыл бұрын
Wow, thanks for quick reply. Your willingness to share is helping so many of us. Know we really appreciate it and you deserve all good that comes your way. Your answer makes sense. I guess worst case is new pinion is different enough from original pinion dimensions that an adjustment to pinion depth becomes necessary. Take care.
@garrettmcgee7183
@garrettmcgee7183 3 жыл бұрын
Good video. My wife was complaining of a tick noise in the front end of her ‘01 grand Cherokee Laredo. I’ve checked the hubs and axles on both sides and they were all good. So I located the noise in the front diff. I assume I’m gonna have to rebuild the front diff but I don’t know much about spider gears any tips?
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
If the spider gears are good but the R&P are bad, no need to replace the spiders. If the spiders are shot, simply remove the roll pin and pull out the cross shafts. Rotate the gears out. Then pull out the side gears. It is very easy.
@robertlopez6787
@robertlopez6787 2 жыл бұрын
Thank you for the very detailed video. You covered everything and pretty much answered all my questions so i feel confident enough to tackle it my self. The only tool I’m having a hard time finding is the rotational mass tool you used. Is that inch pounds or foot pounds? Im working on a 2005 TJ D30.
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
it is inch pounds but it has to be beam or dial style Beam is way cheaper. Type this in your search bar: in/lbs. beam style torque wrench
@robertlopez6787
@robertlopez6787 2 жыл бұрын
@@TheBFHGarage I saw those but I wasn’t sure if that was the same thing. I found it, thank you so much!
@sajzoghet247
@sajzoghet247 3 жыл бұрын
Since we snug down yoke & cap bolts to set back lash & pinion depth, for easy removal & reinstal, will the final specs change when all is torqued to spec?
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
The purpose of putting the bearing caps on and snugging them down is to keep the carrier from moving and making sure it is fully seated to get an accurate reading. Torquing to spec is for final assembly.
@jackrussellville
@jackrussellville 10 ай бұрын
Is the crush sleeve the same on the Dana 30 as the Dana 35
@oldprophet
@oldprophet Жыл бұрын
BBQ Ring 😂 just to get it to fit lose You learn something every day thanx:)
@Imhere-pp5oe
@Imhere-pp5oe 2 жыл бұрын
You are professional
@frankpaya690
@frankpaya690 3 жыл бұрын
I've never seen that method for getting the carrier out of the housing before, that's awesome, I've always pryed it out with one or two pry bars and it can be difficult to get out sometimes or can come out all at once with a "pop" on to the ground or in your face. So to verify your pinion depth is correct for your ring gear/pinion pattern, you don't need any crush sleeve? you can just run it down onto the bearings, ( don't crush them) of course, and would you have to run the nut down tight enough to get the specified pinion preload? Or just making contact, would that be enough to check your pattern and then set up backlash? In my experience, I've had to check for a pattern with the carrier torqued all the way and the preload in range on the pinion as well, because that extra finish torque makes a difference, it makes a difference setting backlash if the carrier is not torqued to specs. everything needs to be torqued to specs I found before, otherwise if you're not quite there when you put it together for the last time and everything is set to specs, that extra tightness I've had it where I can't rotate the ring gear just because it pulls the pinion and ring gear to mesh together tighter. In other words I found to not get a different result when I put it together for keeps, I had to have checked it with the pinion with the specified inch pounds of preload and the carrier torqued in the housing to specs, because a few thousand more pulls it tighter in mesh & will change things, if I didn't check it that way with preload set on the pinion and the carrier torqued.
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
When i first learned of that carrier removal method (from a Wizard) I was so happy to see it work so well! I run the pinion nut without a crush sleeve (or shims depending on the axle) but am careful to not overtighten it. I get it to torque spec range (by feel) without crushing the bearings. That's all it takes. As far as getting to full torque spec just to check, I've never had that issue that you describe. I also always double check pattern and backlash after final assembly to ensure it is correct. If it were to change, I wuold see it then.
@ahmadkamali8547
@ahmadkamali8547 2 жыл бұрын
@@TheBFHGarage good knoldge.. a real exlent answer
@vaibhavmankar4817
@vaibhavmankar4817 2 жыл бұрын
I'm big fan sir
@michaelauskings1352
@michaelauskings1352 3 жыл бұрын
Awesome video. Can you do one for the C8.25? ;)
@patrickcooper1122
@patrickcooper1122 2 жыл бұрын
Why do you heat up the new ring gear before installing it on carrier? And I didnt understand what you ground off on the pinion nut? Was it just the inside edge of the threads? Thank you and Very nice work Sir!
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
The ring gear is such a tight fit around the carrier that it doesn't just slide on. You want to make sure it seats properly on the carrier. If you heat the ring gear, the metal expands slightly allowing it to slide over. As far as making a setup pinion nut, yes, just take off the sharp edges of the threads.
@Driven716
@Driven716 Жыл бұрын
Great video, just awesome instructions. Quick question, so the crush sleeve for preload gets done after you get your shims, etc for depth set, proper patter set... correct ?? :) I know dumb question.
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Not a dumb question at all. A lot of people don't understand that part. You do not install your crush sleeve until final setup. So when you are setting pinion depth and are ready to run a pattern, you need to tighten the yoke nut without the pinion crush sleeve installed and then tighten it down to about 15 to 20 inch pounds. The crush sleeve maintains that preload when it's installed that final assembly.
@arturbobinski2287
@arturbobinski2287 Жыл бұрын
@The BFH Garage perfect, thank you. I am considering jumping on this myself with my 06 LJ to get it to 456. Done everything auto repated other than gears lol wish me luck lol
@joeybaltz582
@joeybaltz582 Жыл бұрын
huge thanks to northridge 4x4 for the opportunity for me to learn how to do a rear end. its so unbelievebly hard to find people comfortable with breaking into the gears i would just rather save the labor money and do it twice for cheaper over a weekend.
@bigjuicygarage4754
@bigjuicygarage4754 Жыл бұрын
When you adjusted the pinion depth you re-checked the backlash. If the backlash had moved out of spec, would you have first removed the carrier & corrected the backlash before running your pattern?
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Yes, exactly.
@ZJ_Rubicon
@ZJ_Rubicon 2 жыл бұрын
How do you know if you have the correct amount of carrier bearing shims for bearing preload? Is it just a feel of puting it in the case?
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
It should take a 6-8 whacks with a deadblow hammer. You shouldn't be able to pull it out by hand.
@keithjohnson3883
@keithjohnson3883 Жыл бұрын
You certainly took the mystery out of this whole procedure for me! You're an Excellent teacher with an excellent ability to explain In detail, this complicated procedure. You’re the best I've ever seen. Because of manufacturing tolerances. Do you check the Depth between your test pinion race and the new race? Do you measure the height with the new and test pinion bearing, before installing it on the pinion? Adjusting by .003, tells me the race tolerance must really be the same, within + - .0005? Are the bearing races manufacturing tolerance that close? I plan on upgrading my 95 ZJ to Detroit Lockers, to deal with our Northern Wisconsin 9 feet of snow on a normal winter. Now I don't feel so intimidated thanks again.
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Nope, none of that. Tolerances are usually very very close. I use the exact same brand and number race or bearing and use new not old to ensure closest match.
@keithjohnson3883
@keithjohnson3883 Жыл бұрын
@@TheBFHGarage Ah yes staying with the same brand is the key, I have a tendency to over engineered things! I'm a retired Instrument Maker from a scientific research community (DOE) I always have a tendency to forget the KISS factor. Thanks again. great job
@DGrant1801
@DGrant1801 Жыл бұрын
Couple of interesting choices there. Liked the idea that you spaced thr pinion race rather than pulling the bearinf iff and respacing it. Atleast for setup.. also, now im curious if im stick spacinf the carrier every time rayher like on other axles whwre you space the carrier races agains the housing..
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Either way works unless you are using an ARB
@DGrant1801
@DGrant1801 Жыл бұрын
@@TheBFHGarage I'm actually in the process of regearing right now, but I opted for E-lockers rather than air. That arb air set up looks kinda like a pita having to deal with that copper line and little end peice. Ive always shimmed the races rather than the carrier and it turns out I have shims for either. Shimming the races is much easier though cause you're not stuck pressing a set of bearings on and off. Did you leave those pinion shims on the race for final assembly or did you pull the bearing off and shim it accordingly. I guess it wouldnt matter either way but I kinda like that idea of not having to press stuff on and off more than I have too.
@TheBFHGarage
@TheBFHGarage Жыл бұрын
@@DGrant1801 set up pinion race. Install shims under the new race.
@gatordave6629
@gatordave6629 2 жыл бұрын
Have you ever had a issue with that ring gear expanding too much out of the over where the bolt holes won't line up? What temp and how long did you put the ring in the oven
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
Never had a problem. 200° for about 20 minutes is all. Unless you want well done 😂
@cantfixstupid5503
@cantfixstupid5503 2 жыл бұрын
so, after the pinion main bearing is pressed on and piggybacking the oil slinger.. WHERE do you put additional shims for depth? behind the Race?
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
You can use the slinger as your shim if it's the right thickness OR you can place shims behind the race. Most people don't have a variety of slingers so most likely you will use shims behind the race.
@thomasfreedy
@thomasfreedy Жыл бұрын
Great channel!! Is it better to do a setup race or bearing?
@TheBFHGarage
@TheBFHGarage Жыл бұрын
Either works well.
@shorthood2518
@shorthood2518 2 жыл бұрын
The weird spacer that northridge machined is actually part of the install kit from them. It's the main shim that gets other thin shims stacked into it.
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
ARB Air Lockers have everything you need to do the install correctly. You shouldn't have to fabricate something to work. There is no need to have the other shims stack "into" it. The machining on it was horrible so I highly doubt this is a go to part for Northridge. Completely unnecessary.
@shorthood2518
@shorthood2518 2 жыл бұрын
@@TheBFHGarage I appreciate the response. I'm currently installing a tru-trac and 4.10s in a JK Dana 30. A pair of stepped spacers are included in "PVTNORD30-JK" install kit. They might not be of any value, but they are sold in that kit
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
@@shorthood2518 it might be for that kit, but definitely not for an ARB and that's what this video is about👍 to be honest I would hate to see that as part of anybody's kit since the tolerance was so far off. The run out and that so-called spacer was over .005" from one side to the other which is completely unacceptable for me. That's the quickest way to get gear jobs back to your shop for warranty.
@v7nf
@v7nf 3 жыл бұрын
I did a ford 8.8 swap on a jeep and theres a 350 in the works but I never did a rearend rebuild,so I went through 5 crush sleeves and nuts.....they gave me the whole box of pinion nuts and sleeves they had at parts store as a joke,I have like 10 left.everything turned out okay my pinion depth isnt very good,everything else perfect,my gear pattern on the coast side is kinda high,drive side is perfect ,its bothers me.I decided to say fuck it for now I get back to it latter, I still have to weld my bracts on it and line up my drive line and get my engine in there right and order my shafts.good vid,youve made me confident
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
If you are going to redo it, be sure you do it before driving it. One you break in the gears they work harden and changing it after won't be good.
@v7nf
@v7nf 3 жыл бұрын
Jesus christ
@williamthompson969
@williamthompson969 3 жыл бұрын
I wish I had this guy do my gear setup. I had to take the yj back today because front seal leaks and rear axle whine
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
That sucks!
@williamthompson969
@williamthompson969 3 жыл бұрын
Yeah after this video and a couple tools I could have done it myself
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
@@williamthompson969 that's the goal!
@shawnt1975
@shawnt1975 3 жыл бұрын
That’s my Jeep getting a regear. It’s was needed due to a sloppy install but a “reputable” shop
@cheepojeepo5681
@cheepojeepo5681 3 жыл бұрын
What's your opinion on the HP Dana 30? Do you see a lot of them destroyed? What's the most common failure you see? Thanks in advance.
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
I like them for what they are. It's a Dana 30. As long as you don't run bigger than 35" tires they hold up really well. Chromoly shafts are a must in my opinion. The Dana 30 uses the same ball joints as a Dana 44 so strength wise they are fine. Weakest point would be the shafts unless you upgrade to chromoly. After that I would say the ring and pinion but I've only had one of those fail.
@jasonbodi503
@jasonbodi503 2 жыл бұрын
High Pinion 30 uses shims. That explains why I didn't see a crush sleeve in my D30 on my 92 Cherokee. I'm still confused though. How do I get proper preload on my pinion with the shims you say come in the HP Dana 30?
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
There are smaller shims that go between the tail bearing and shoulder on the pinion gear. Adding or subtracting shims will make less or more preload. When you find the right amount of shims, you can torque the nut to spec and be done. No need to worry about overcrushing a crush sleeve.
@LozanoL1
@LozanoL1 2 жыл бұрын
Excellent video I'm working on my 06 Wrangler with D30 on the front..bought a Grizzly locker and I pressed bearings with no shims in place so I have to install them outside the race. My question is where can I buy the larger, thicker Shims?or item# I order for D30 but keep getting the smaller ones for the inboard installation..any help is greatly appreciated 🙏
@TheBFHGarage
@TheBFHGarage 2 жыл бұрын
You'll have to measure your old ones and compare to shim kits it there. They're all over the place
@LozanoL1
@LozanoL1 2 жыл бұрын
@@TheBFHGarage ok Thanks
@caseyhadland2273
@caseyhadland2273 3 жыл бұрын
At 19:39 you mentioned that you ground out the inside edges on a normal nut so that it doesn't cut into the threads of the pinion. How do you make this set up pinion nut. Do you take a drill to all the inside threads of the nut? Grinding down the peaks of the threads? And a normal nut meaning a normal pinion nut or a normal nut from hardware store with out any oblong locking features. Could I just use my old pinion nut as a set up nut? Great video thanks for posting.
@TheBFHGarage
@TheBFHGarage 3 жыл бұрын
Yes use the old pinion nut. I take a dremel with a sanding drum on it and just take off the sharps edges of the threads.
@caseyhadland2273
@caseyhadland2273 3 жыл бұрын
@@TheBFHGarage Ok will do that. thanks for responding and for sharing your knowledge.
How To Re-Gear a Dana 44
53:01
The BFH Garage
Рет қаралды 163 М.
THEY WANTED TO TAKE ALL HIS GOODIES 🍫🥤🍟😂
00:17
OKUNJATA
Рет қаралды 15 МЛН
Final muy increíble 😱
00:46
Juan De Dios Pantoja 2
Рет қаралды 45 МЛН
The day of the sea 🌊 🤣❤️ #demariki
00:22
Demariki
Рет қаралды 100 МЛН
Regearing Dana 30 HP / 4:10 To 4:88 / Elite Gears
27:41
Workshop to Wilderness
Рет қаралды 24 М.
Rebuilding a 4.0L Jeep Straight Six to 242HP - Engine Power S2, E14
18:43
Axle Regearing made EASY - Dana Series Axles
1:02:46
War Paint Offroad
Рет қаралды 770
Ultimate Dana 30! Steering, Brakes and Axle Shafts! - Episode 3
20:05
Dirt Lifestyle
Рет қаралды 243 М.
Gearless Magnet Bike
17:57
Tom Stanton
Рет қаралды 6 МЛН
Gear Install Jeep wrangler (yukon 4.88 gear)
35:52
WarPig Off-road
Рет қаралды 160 М.
Pinion Depth Checking With Simple Tools
31:23
Acme Machining
Рет қаралды 70 М.
The Ingenious Mechanics of Driveshafts
21:28
New Mind
Рет қаралды 340 М.
Manual Transmission Operation
24:04
WeberAuto
Рет қаралды 10 МЛН
Qual ELEMENTO é Melhor para ESCAPAR😱 #shorts
0:26
Lucan Pevidor
Рет қаралды 16 МЛН
Моя супер находка для велосипеда #находки #wildberries #топ
0:14
Surprised 😳🤩🤩❤️🔥🥳
0:35
Okanutie
Рет қаралды 30 МЛН
CHARGING METHOD FOR CARDBOARD iPhone!#asmr
0:31
HAYATAKU はやたく
Рет қаралды 12 МЛН
VOCÊ ME AJUDARIA ?
0:46
JHONIC
Рет қаралды 39 МЛН