Honda Mower GCV160 Keihin Carburetor Service

  Рет қаралды 130,448

The Lawnmower Lady

The Lawnmower Lady

Күн бұрын

DIY tutorial to diagnose and service a clogged up Keihin carburettor on a Troy-Bilt mower with a Honda GCV160 engine. Ethanol in petrol leads to water damage in small engine carburetors. Check the Thermowax plug if it's hard to start when cold.
Auto choke assembly: amzn.to/3fULec0
Extra gaskets: amzn.to/3znPSqL
Bowl gasket only ( not included with gasket set): amzn.to/3gi6aK8
Thermowax plug: amzn.to/3cprGum
If all else fails a complete carb ( should come with gasket set) amzn.to/3pPgA79
Rewind or skip ahead to watch again:
00:00 I'm not Rusty
01:33 Recoil, shroud, and tank removal
03:43 Remove carb bowl
06:45 Carb removal, gasket configuration
09:03 Exterior clean and disassembly
10:43 Manual clean jets and reassemble
19:02 Re-attach fuel line and linkages
22:07 Reassemble airbox, gaskets and auto-choke
26:04 Install tank, shroud and recoil
27:21 The Money Shot
The tools I like and use most often:
Magnetic spark plug socket set: amzn.to/3CzmpvO
Tachometer: amzn.to/3sHibiH
Vessel Megadora JIS screwdriver set: amzn.to/363RFqO
Channellock Bent Needle-nose pliers: amzn.to/3I5DbnA
Long 1/4 Quick-connect Torx Driver Bits: amzn.to/3HUNgnm
Spark Tester: amzn.to/3CxW2qi
OTC Leak-down Test Kit: amzn.to/3CyUhJn
Compression Tester: amzn.to/3IWd6sp
Wear your safety glasses, or you'll put your eye out. Try on some gloves. Take off that spark plug boot. Clean your room. Open the windows, those fumes are nasty. Just 'cause I do it, don't think it's the end all, be all solution. There's plenty more ideas out there, I can't take responsibility if you slice off a few fingers after watching my videos. And don't just pour that toxic stuff down the sewer or in the ditch, dispose of waste responsibly. Just be safe, OK?
Follow along with me elsewhere:
/ thelawnmowerlady
the-lawnmower-lady.blogspot.com/
Titles, opening graphics, and music by AbleVFX.
Any links to products are likely affiliate links, and I may earn a small commission from qualifying purchases (Thank You!), with no additional costs to you.
Disclaimer: The content of this video is purely for my entertainment, and is available to you for informational and educational purposes only. It's not substitute advice from small engine mechanics with professional training and certifications, nor does it create any kind of relationship between the The Lawnmower Lady and you. Your situation may be different, and the The Lawnmower Lady makes no warranties, express or implied, as to the fit, accuracy, or applicability of the information shown in this video, and implies no guarantee of results. The Lawnmower Lady and any sponsors of this video are not liable for any damages of personal injury, property damage or loss of any kind that may result from the use or reliance on this video and/or any parts and procedures represented in this video. You are using the information presented in this video solely at your own risk.
#honda #gcv160 #carburetor #keihin #lawnmower #smallenginerepair #DIY

Пікірлер: 472
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
If this video helped you, please consider clicking on the THANKS button above 🙌 Here's some other Honda videos you might like: kzfaq.info/get/bejne/qN5gmMmEv9arZ3k.html
@jimyeske8498
@jimyeske8498 2 жыл бұрын
Sorry! My bad… The next video I watched, there you were using M6x1 dowels! 😊 Well done. I’ll keep watching.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
@@jimyeske8498 No worries Mr Jim. I just appreciate you watching. Cheers!
@jimyeske8498
@jimyeske8498 2 жыл бұрын
What you also need are the Briggs and Honda oil extractors! As seen in The same Bruce video. If you’re interested in the details. I can email some photos.
@JazzyScat
@JazzyScat Жыл бұрын
Hi. I commented here about an HR214 lawnmower carburator change. I don't know why my comments and your replies aren't here anymore. Anyways. I changed the carburator everything is in place and the mower problem stopping when changing the manual lever from choke to hi or low is corrected but when I change from hi to low it revs at the same speed. Any ideas?
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
@@JazzyScat hmmm odd. I remember and the replies are missing for me too. I can only suggest the control cable is out of adjustment, or it's slipping?
@mariobannano6592
@mariobannano6592 2 жыл бұрын
I like the lawn lady she is calm n keeps simple n explains step by step I think she knows her stuff, God bless her.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I appreciate you watching Mr Mario. Cheers!
@philliphall5198
@philliphall5198 Жыл бұрын
She does
@HenryFL1
@HenryFL1 2 жыл бұрын
I’ve watched many “ so called “ experts on the maintenance of a Honda carburetor but yours was the most direct , step by step method - easy to understand for even a beginner like myself ! I was ready to bring in my mower ( only 8 months old ) for repair until I came across your video !
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
comments like this make it worth every minute i put into this. Thank you so much for watching and welcome to the channel Mr H&J. Cheers!
@tucker4174
@tucker4174 3 ай бұрын
Ma’am. I’m a diesel tech by trade and haven’t been able to get my mower to run worth a damn. It’s a Honda with the same exact carb set up as this mower. This video fixed that. Hats off to you!!!! Fires up first pull with ZERO issues now. Keep up what you’re doing.
@TheLawnmowerLady
@TheLawnmowerLady 3 ай бұрын
Yay! I appreciate you watching. Cheers!
@davidcurnutt9584
@davidcurnutt9584 3 жыл бұрын
Keepin it simple makes you a winner every time
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you Mr. David! I strive to KIS, it's easy to get distracted.
@CP-pj8lw
@CP-pj8lw 2 жыл бұрын
After spending three hours fiddling with reinstalling the carb of my gcv190, I found your video, followed your guidance and BINGO, got it done in just a few minutes! Your many many helpful tips and clear instructions made me confident that I can keep my equipment in top shape. I learned the hard way to mind the float valve…luckily found it at my feet:). Thank you Lawnmower Lady!❤
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad I could help. Thanks for watching!
@paulinswfl8218
@paulinswfl8218 Жыл бұрын
Best video on the Honda carb out there, no question. Thank you! Saving us regular folk lots of dollars.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@tbonky
@tbonky 2 жыл бұрын
Thanks LL! You did a great job of showing the detail points that others left me scratching my head on, the atomizer jet, the float needle, etc. excellent close-up work. keep on rockin' it!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Mr Raymond! Comments like this make me feel it's worth the effort. Glad to help. Cheers!
@beakittelscherz5419
@beakittelscherz5419 Жыл бұрын
Totally underrated Channel imo😎 Thanks for the upload and positive thinking! Helped me a lot😁👍👌
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you for your kind words. Cheers!
@derekknight4199
@derekknight4199 2 жыл бұрын
Thank you so much for your information and willingness to share and teach. Your videos, particularly this one and other on this carb type, were very helpful and very well put together. I have been fiddling with my Troy built mower for a while now and each time it’s either just as bad or even maybe worse…until finally it would only run while choked then would stall out. So this carb breakdown was exactly what I needed to give me the confidence to dive in all the way and fix it right! Thanks again!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
You got this Mr Derek! I appreciate you watching. Cheers!
@alsmithph.d.9851
@alsmithph.d.9851 Жыл бұрын
Your video saved me and made me look like a hero in front of my family!! Thank you!! So easy to follow! Started on the first pull!!! 💪🏾
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Great job!
@jamesgaskill11
@jamesgaskill11 Жыл бұрын
Just like everyone said previously, you took the time and really showed in detail on how to take it apart and then reassemble the carb makes it easy to service or replace if you have to.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@gb3450
@gb3450 Жыл бұрын
I appreciate the parts lists too!
@umpquajohn
@umpquajohn 2 жыл бұрын
Great video and great job of explaining everything you were doing and why. I have this same mower and have had the carb off before but your video was a great refresher and I learned some new things. Thanks-you are a natural teacher.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I appreciate you watching! Cheers!
@gl35
@gl35 Жыл бұрын
This is the best video I have seen yet on this Honda engine. Thanks for a very precise, step-by-step instruction.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad to help. Thanks for watching. Cheers!
@duskmean
@duskmean Жыл бұрын
Got my mower running again! Carb looked pretty new but cleaned it anyway and it's running again. Thanks for the video!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Happy to help! Thanks for watching. Cheers!
@scottwheaton9689
@scottwheaton9689 Жыл бұрын
You did an excellent job explaining how to remove,clean,reassemble this Honda gc160 dirty carb to a great 1 pull to fire up outcome! Keep up the great work!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks 👍 I appreciate you watching!
@garylinder5507
@garylinder5507 Жыл бұрын
Lawnmower Lady, this is probably the best video I have seen in a long time. It's the first video on carburetor where someone begins by showing you how to remove the carburetor and putting it back on step by step. I had gotten fluster with the process. Thanks Lawnmower Lady.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you Mr Gary for watching. Cheers!
@rogermcdonald1607
@rogermcdonald1607 3 жыл бұрын
Stella, that was a nice demonstration and narration of cleaning the Honda carbs. Ive wrestled with enough of those gaskets, heat shields, etc. I went to the hardware store and bought 2 bolts ,1/4 inch longer and cut the heads off and use them as studs. Made my life alot easier and they work on all Honda small engines. Keep the videos coming. Looks like you enjoy what your doing! 👏👏👍🇺🇸 Roger
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thanks Mr. Roger for watching! I have some long threaded rods from a three arm puller that I use sometimes (when I remember :embarrassed: ) every now and then.
@kenortiz8295
@kenortiz8295 2 жыл бұрын
Lawnmower lady, you are the best. You saved me money time and frustration. And I will only be using true fuel from now on. Excellent video, thanks so much.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I'm happy to help Mr Ken! I appreciate you watching. Cheers!
@eddiepatterson5025
@eddiepatterson5025 3 жыл бұрын
I’ve always stored my mower with Stabil original formula stabilizer never had trouble till a couple years ago or so. Till my power valve stuck after I fixed it I watched a Stabil Marine 360 stabilizer. I got to thinking about it the marine formula it’s made to absorb condensation from the boat tanks I’ll try it in my mower and in storage. For the last two or more years it works really well doesn’t gel up to clog the carburetor. I’m using regular unleaded with the crappy ethanol and not a moment’s trouble. Have a Blessed One. Greetings from Silverstreet South Carolina.
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Anything you do is better than doing nothing if you need to store it for a while.
@rayburnett3066
@rayburnett3066 2 жыл бұрын
I use my zero turn mower about 12 months of the year. I also use 87 octane gas in all of my mowers too. I have a Murray 38 inch that has had always had 87 octane gas in it. Never had NO problems with it
@kachiquitaito3341
@kachiquitaito3341 2 жыл бұрын
Me too, I have a self propel brigg Stratton engine for 15 years I also use 87 octane gas and never have a problem.
@1TrueDenesha
@1TrueDenesha Жыл бұрын
I searched and searched and finally came across your video by searching auto choke Troybilt. I can’t give you enough praise! Every guy that did a video had a fraction of a fraction of details that you did! I was stumped, but you squared me away. By far the BEST VIDEO of any instructional how to videos out there! I’m an HVAC tech by trade, but am now many steps closer to becoming my own diy small engine repair tech as well. THANK YOU!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I'm so happy to help. Cheers!
@carlbikharie6832
@carlbikharie6832 Жыл бұрын
I watched your video and agree that it is the most comprehensive of all. Thanks and keep up your good work.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Much appreciated!
@alexisrivera7650
@alexisrivera7650 Жыл бұрын
Very easy the way you explained it. Ordered the RIGHT parts and started right up. With a few mowers to work on I’ll be subscribing. Thank you.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you! Cheers!
@BrucesShop
@BrucesShop 3 жыл бұрын
I like the pick idea in the intake hole. It is fun the watch someone else work on a carb. Good work.
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thanks 👍 Mr. Pender. I've enjoyed watching your videos for a long time.
@kasaloub.bennett9878
@kasaloub.bennett9878 11 ай бұрын
Omg 😮you saved my life. Your video has taught me so much. I had to rewind how to screenshot it took me all day, but I feel so confident now about my own mower I cannot thank you enough I literally could start crying.!!!! 😅😊A MILLION LITTLE THANK YOUSE 🙏🏼🙏🏼
@TheLawnmowerLady
@TheLawnmowerLady 11 ай бұрын
Happy to help. Cheers!
@fredkaboom
@fredkaboom Жыл бұрын
Thanks a bunch for clear, detailed, and timestamped video! My lawnmower stopped working halfway through mowing my lawn. It would start, but immediately stop. Google suggested cleaning my carburetor would be a likely fix. This video let me confidently take it apart, and more importantly, put it back together again, fixing my lawnmower and saving me from the humiliation of my lawn looking like Ronaldo at the 2002 World Cup.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I had to google Ronaldo, nice hair-do LOL. I'm happy I could help. Cheers!
@bokuwahimodesu
@bokuwahimodesu Жыл бұрын
Never took a carb apart before but I got the clog out of my jet and my mower running in no time after watching this video. I used a piece of a plant that was skinny enough to bore the hole out. Thanks, Lawnmower Lady!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it helped. Thanks for watching. Cheers!
@s1rky01
@s1rky01 2 жыл бұрын
This video helped me so much. I needed to see the gasket order and you did that. Thanks a lot!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
You're very welcome! I appreciate you watching. Cheers!
@georgemyers6518
@georgemyers6518 3 жыл бұрын
Great video and great job explaining everything thoroughly. I like that. Please keep the videos coming
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you for watching Mr. George! Hope you subscribe and stick around. Cheers!
@mskinch9
@mskinch9 Жыл бұрын
Best step-by-step video for the Honda GCV160 carb replacement.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks, I appreciate you watching. Cheers!
@Encourageable
@Encourageable 7 ай бұрын
Thanks. Some good tips in your video that I didn’t see elsewhere. If it wasn’t for getting those two bolts through so many assemblies this would be a piece of cake!
@TheLawnmowerLady
@TheLawnmowerLady 7 ай бұрын
I have since fabricated some M6 threaded rod to replace the bolts, to assist with that gaggle of gaskets. My more recent Honda carb service videos show that. Thanks for watching!
@peterlance2344
@peterlance2344 Ай бұрын
This is such a great video! Super helpful and she really knows her stuff. A great tutorial on how to troubleshoot my carb issues. Well worth sending her a “Thanks” tip.
@TheLawnmowerLady
@TheLawnmowerLady Ай бұрын
Glad it was helpful!
@yamuson08
@yamuson08 Жыл бұрын
By far the best video on this carb. I was planning on just tearing into it, as I've cleaned a handful of carbs, but I'm glad i watched this first, because i would have probably messed the gasket orientation up when I pulled it apart.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Happy to help. Thanks for watching!
@yamuson08
@yamuson08 Жыл бұрын
​@@TheLawnmowerLady just cleaned her up. First pull. So satisfying 😁
@thx1138guy
@thx1138guy Жыл бұрын
I didn't watch how the float needle dropped out when I took my carb apart. Yours is the only video I've watched thus far which shows the direction the needle goes into the port. That was very helpful as I was about to install the needle upside down. This was my first stab at small engine carburetor cleaning.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it helped. I appreciate you watching. Cheers!
@BrianReeves2
@BrianReeves2 2 жыл бұрын
Another happy 'customer' here, watched your video the other day and fixed my mower in about thirty minutes. The hardest part for me was pulling off the fuel line, I think. My machine is only a few years old and wasn't that dirty, but there was a little gunk somewhere that was causing it to hunt quite a bit. Running much stronger now. Thank you.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Great to hear that Mr Brian! Glad to help, Cheers!
@realchuckwow
@realchuckwow 2 жыл бұрын
lawnmower lady - thanks for the to the point and very informational video. it was just what i needed to get things apart and more importantly back together.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad it was helpful Ms Lynn! Thanks for watching. Cheers!
@brianfidler1123
@brianfidler1123 Жыл бұрын
Awesome video. You are a master mechanic. Well done!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks 👍 I appreciate you watching!
@garybeasley4885
@garybeasley4885 Жыл бұрын
One of the best how to videos Ive seen, thank you!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Wow, thanks!
@paoemantega8793
@paoemantega8793 Жыл бұрын
Nice work there, keep em coming you are a gem !
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Much appreciated!
@amyk.2293
@amyk.2293 4 ай бұрын
Great video! I was able to clean off and reassemble my Honda GCV160 carburetor thanks to your video!! Excellent job :)
@TheLawnmowerLady
@TheLawnmowerLady 4 ай бұрын
You're welcome! I'm so happy to help. Thank you for watching. Cheers!
@darshanmutta6613
@darshanmutta6613 Жыл бұрын
An awesome job of explanation step by step. Warning about every step of the way, while cleaning & putting it together. Keep up the good work, I have GCV 160 Honda. Your video was the best one from all of them. I am quite confident that I can repair my Carb. George
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it was helpful. Cheers!
@chuckcarson7196
@chuckcarson7196 Жыл бұрын
Wow, awesome video. Great detail, and great photography. Thanks for sharing all your tricks of your trade. Very helpful.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it was helpful!
@brucegarry1402
@brucegarry1402 Жыл бұрын
Thanks for this video. My small engine guy retired so I'm on my own. My GCV160 on a Craftsman won't run except a few seconds with starter fluid in it. There is fuel flow and the spark plug looks good and it will run for a few seconds which tells me there's spark. So it comes down to the carburetor which I took off and mine looks nothing like yours. It was fairly clean and the needle looked ok. Stumped, I ordered a new carburetor though there is no obvious fault with the one I have. The mover is a 2019 and been kept in a garage. I've never had an issue with a Honda engine before. You video was great for showing me things to look for though my carburetor is slightly different.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Did you take out the idle jet on top? Yours might have a plastic idle speed adjustment screw that needs to be removed. The plastic jet cones out and has to be clean. Tom, at @vintageemginerepairs has a great video on that style of carb.
@wallacetom1
@wallacetom1 8 ай бұрын
As always great video.professional and easy tp follow
@bobthompson865
@bobthompson865 Жыл бұрын
Great video. Able to follow easily. Thanks. I have a lawnmower and a pressure washer with this engine, so very helpful.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Great to hear!
@Owl57
@Owl57 Жыл бұрын
Excellent job! Concise and complete. Many thanks.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it helped!
@jacobgray3746
@jacobgray3746 Жыл бұрын
Fixed my issue started on the first pull thank you so much!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Yay! I'm happy to help. Cheers!
@sheilalapointe7828
@sheilalapointe7828 Жыл бұрын
Thanks for all your amazing details ! I was hoping to replace the carborater! I feel confident to look at it now!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it was helpful! The original carbs are far better and more reliable than a lot of the aftermarket junk out there. Cheers!
@sheilalapointe7828
@sheilalapointe7828 Жыл бұрын
​@@TheLawnmowerLady I saw they don't cost too much.... Thanks
@bradrichardson6161
@bradrichardson6161 2 жыл бұрын
Nice n easy to understand even from australia. Fixed my stop starting issue with my Honda. Thanks mate 👍
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
G-day Mr Brad! Great to hear my video helped. Cheers!
@robertv2787
@robertv2787 Жыл бұрын
Very nice video, thanks very much! Very helpful! Those Hondas are such a pain with those long bolts and so many gaskets to get in the right order.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks! Honda makes a very pricey “tool” for this that is really the bolts with no heads. I fabricated the same thing with two 6mm threaded studs. Most any other of my other Honda carburetor videos show this. Makes the job easier. Cheers!
@theluckyjameseller442
@theluckyjameseller442 2 жыл бұрын
I told you'd hit 1k lastnight congrats
@mrjuvenalify
@mrjuvenalify Жыл бұрын
The best video I have ever watched... Now, I have to figure out how to set the throttle stop and pilot screws positions... Ty!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching!
@ftwopointeight
@ftwopointeight 2 ай бұрын
I took the jet out and the atomizer rod came out and didn't know which way it went back, until I saw your concise breakdown and rebuild. Thank you! (I had it in correctly, but my luck dictates that I probably didn't)
@TheLawnmowerLady
@TheLawnmowerLady 2 ай бұрын
Happy to help. Cheers!
@cyberpunk2
@cyberpunk2 Жыл бұрын
Hey ! Thank you so much ! You really helped me figuring this thing out , all the best !
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@jphthree3
@jphthree3 Жыл бұрын
Thank you Lawnmower Lady!! I have a Yard machine with a Honda engine, it won't stay on longer than about 3 or 4 minutes, about 20 feet of lawnmowing 😢. I think this is my next step. With your guidance, I think I'll successful!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Be sure and check your fuel cap. The vent might be clogged with debris. Next time it stops, crack open the fuel cap and see if it starts up. Without a vent to atmospheric pressure, as the fuel leaves the tank, it can create a vacuum that a gravity fed fuel system can't overcome.
@jphthree3
@jphthree3 Жыл бұрын
@@TheLawnmowerLady already unplugged the vent holes in the gas cap along with changing the air filter, oil and spark plug. So, with your awesome assistance, it's off to clean the carb. Have looked into a ultrasonic cleaner too. Love your videos, your an excellent teacher and thanks for sharing!
@agapitorodriguez414
@agapitorodriguez414 Жыл бұрын
Awesome video,stay safe doing it tomorrow
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Good luck!
@paulwharton1850
@paulwharton1850 Жыл бұрын
Amazing ! Such a clear, useful video - I learnt a lot. Many thanks......all the way from London.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
You're very welcome! I appreciate you watching. Cheers!
@jafinch78
@jafinch78 2 жыл бұрын
Great step by step detail video detail. Appreciate that! Thank you much! Liked, subscribed and commented.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@prophtube
@prophtube Жыл бұрын
thank you! was hard for me to figure out the float needle until I saw you mention it here
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad to help. Thanks for watching!
@rf4c1018
@rf4c1018 Жыл бұрын
Your video is the BEST on KZfaq! Thank you,.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks for your kind words. I appreciate you watching. Cheers!
@kenjohnson5498
@kenjohnson5498 8 ай бұрын
Thanks lady i got a lot of info from this video without trying to over complicate things.
@TheLawnmowerLady
@TheLawnmowerLady 8 ай бұрын
Glad it was helpful!
@tomwilson5201
@tomwilson5201 Жыл бұрын
I had to subscribe. You are so Professional about your work. Awesome!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Wow, thank you!
@tomwilson5201
@tomwilson5201 Жыл бұрын
Very well done! Love it!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thank you! Cheers!
@jeffreya.657
@jeffreya.657 Жыл бұрын
I am real familiar with these GVC 160s what a great video you made. thank you for making everything look easy. but I always called your emulsion tube a venturi tube thanks for the correction I will add that one emotion tube sludge is the main thing on nearly every carburetor that causes surging rpms. anyway it's great listening to do you do this for people. You do a great clear explanation. Thumbs up.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it was helpful! I often call it an atomizer ( I come from antique scooter world) and this is what Dellorto calls it in their older documentation. I appreciate you watching. Cheers!
@ronniebarker79
@ronniebarker79 2 жыл бұрын
Loving your work lawnmower lady
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad to hear it Mr Ronnie!
@ronniebarker79
@ronniebarker79 2 жыл бұрын
Looking forward to your next episode and what lands on your job sheet
@onenuttybuddy
@onenuttybuddy Жыл бұрын
Great video. I bought a new carb for my GCV160. However, after watching your very well-done video, I'm going clean the old carb and reuse it. I'm going to return the new carb and get my money back. Very appreciative!! Thanks a ton!! 😀
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I all honesty, unless it's really corroded or rusted up. They are better than the cheap imports. Thanks for watching!
@onenuttybuddy
@onenuttybuddy Жыл бұрын
@@TheLawnmowerLady Thanks for the info. I have one more question: I tried to remove the cover, like you did in your video. I ran into a problem. The left and right nuts came off just fine. However, the bolt on the front of the couling came loose a little, then it just spun and spun. I couldn't get the nut off the stud. Any ideas of what might be going on? I really appreciate your help. Thanks again!!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
@@onenuttybuddy if it's the one I'm thinking of, I'm afraid that might be one of the studs that also hold on the ignition coil. Once you get it off you'll have to reset the gap on your ignition coil. Just use a business card and slide it between the flywheel magnets in the coil and then tighten down that stud. You might try a little loctite on the stud. Loctite blue not red.
@onenuttybuddy
@onenuttybuddy Жыл бұрын
@@TheLawnmowerLady I can do that, not a problem. Thanks LL, much appreciated!!👍
@CarlosGonzalez-mr5qz
@CarlosGonzalez-mr5qz Жыл бұрын
This video was very helpful thank you!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Happy to help. Thanks for watching. Cheers!
@TLMD
@TLMD 2 жыл бұрын
Very good video Lawnmower Lady! Keep up the great work!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Sgt! Will do!
@bradcoleman6221
@bradcoleman6221 4 ай бұрын
Thank you for a great video. Very informative and helpful!
@TheLawnmowerLady
@TheLawnmowerLady 4 ай бұрын
Glad it was helpful! Thanks for watching. Cheers!
@bobbymuse7793
@bobbymuse7793 Жыл бұрын
I learned so much from your video. When I removed the carb it all fell apart so I had no frame of reference for the gasket orientation and auto choke.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad it helped. Cheers!
@genepitts4665
@genepitts4665 Жыл бұрын
Thank you my lawn day was saved.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad to hear it. Cheers!
@davea5150
@davea5150 2 ай бұрын
Your a wonderful teacher ❤️
@TheLawnmowerLady
@TheLawnmowerLady 2 ай бұрын
Thank you! 😃
@kevinkelliher6331
@kevinkelliher6331 3 жыл бұрын
Kev here in Ireland great video love that little screwdriver
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you. Mr. Kevin for watching! Cheers!
@Mr.G626
@Mr.G626 Жыл бұрын
Excellent video, it helped me out!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Glad to help. Thanks for watching!
@sonton8530
@sonton8530 2 жыл бұрын
Very good teacher. I learned a lot from your video. Thanks
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad it was helpful!
@themowerman
@themowerman 3 жыл бұрын
Yeah another one done by a professional.. great work sister..
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you Sir Mick. That means a lot coming from you. Cheers!
@Ppp-kk6hw
@Ppp-kk6hw 2 жыл бұрын
Big up from Scotland 👍
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Cheers! Thanks for watching.
@stonewalljacksonmcspaddeni2802
@stonewalljacksonmcspaddeni2802 Ай бұрын
Hell yeah! This helped tremendously!
@TheLawnmowerLady
@TheLawnmowerLady Ай бұрын
Happy to help!
@andrewdarnley4608
@andrewdarnley4608 Жыл бұрын
We've had this Honda GVC160 motor on an emergency lawnmower for the last 10 years. It's never run well and I've spent many hours trying to get it perform smoothly. In Australia they come with a manual choke and the idle screw is placed in such a way as to make it impossible to adjust once the carburetor is back on the motor. Along with the air box and the gaskets, they are the work of the devil. I take my hat off to you madam.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Cheers Mr Andrew! They can be difficult. i appreciate you watching!
@rickthelian2215
@rickthelian2215 2 жыл бұрын
Great job Stella, they are a handful but good advice to turn of fuel flow after use.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Yep Mr Rick, got in the habit of turning off fuel tap from the antique scooter world. Thanks for watching. Cheers!
@jdub-replicant
@jdub-replicant Жыл бұрын
great instructional vid, thank you so much!
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I appreciate you watching. Cheers!
@georgeian3243
@georgeian3243 3 жыл бұрын
Nicely done, thank you. If you apply a small amount of dish-soapy water onto the outside of the rubber hoses, the clamps will slide along a bit easier. Of course, you don’t want to get any inside the hose.
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thanks Mr. George for watching. I have several bottles of soapy water in the shop to look for leaks. Need to remember to squirt those hoses. Cheers!
@INSIDEHOUSEGARAGE
@INSIDEHOUSEGARAGE 3 жыл бұрын
you did an excellent job. I appreciate your personality.
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you so much 🤗 I've enjoyed watching your channel(s). Your voice-over style keeps your videos moving at a great pace, and you cover a lot of great info.
@INSIDEHOUSEGARAGE
@INSIDEHOUSEGARAGE 3 жыл бұрын
@@TheLawnmowerLady thank you
@alexisrivera7650
@alexisrivera7650 Жыл бұрын
This was perfect although may need to buy a rebuild kit . Thank you.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Thanks for watching. Cheers!
@stevenphoenix
@stevenphoenix 10 ай бұрын
Great vids best I've seen thanks
@TheLawnmowerLady
@TheLawnmowerLady 10 ай бұрын
Wow, thanks! Cheers!
@Robsenginerepairs
@Robsenginerepairs 2 жыл бұрын
Nice job on there clearing the carb Stella
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks Mr Rob. Cheers!
@TheRustyRooster
@TheRustyRooster 3 жыл бұрын
Awesome job love the shirt, I too have been a fan of using guitar strings for years.
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you Mr. Rooster. I dug through my shirts to find this one for you!
@TheRustyRooster
@TheRustyRooster 3 жыл бұрын
@@TheLawnmowerLady thanks I really enjoy your channel 😊
@wolfmanrepairs
@wolfmanrepairs Жыл бұрын
Love it!! You got yourself a new subscriber!!! 🐺😁
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
Yay! Thank you!
@oatnoid
@oatnoid 2 жыл бұрын
First pull! Awesome!
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks!!
@user-yi4tp3kp3h
@user-yi4tp3kp3h 10 ай бұрын
You are amazing thanks for teaching.
@TheLawnmowerLady
@TheLawnmowerLady 10 ай бұрын
Thanks for watching!
@mulonru2965
@mulonru2965 2 жыл бұрын
Thanks for explaining in detail
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Glad it was helpful Mr Mulonru! Thanks for watching.
@larrycarlston4044
@larrycarlston4044 2 жыл бұрын
Wonderful video. I'm a certified Honda small engine tech and thought you explained the carb clean process so the average homeowner could understand and follow the process. The only point I would add, and maybe you already did this, but I would have drained the gas tank as there was obvious water in the bowl. If you already did it prior to the video. I apologize. Thanks again...
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you Mr Larry! Indeed I do lots of things that don't end up in the video if I feel its is getting too long. I will say, my editing skills have tightened up and I can include more things. I appreciate your views and you comments. Cheers!
@tiriclon
@tiriclon Жыл бұрын
Muchas gracias. Excelente vídeo. Ha sido muy útil.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
De nada Sr. Luis. ¡Salud!
@TodayzTomSawyer
@TodayzTomSawyer Жыл бұрын
Tool tip: I used a piece of multi strand copper wire with the end stripped to clean out all the small holes. One strand for the smallest, a couple twisted together for the biggest ones.
@TheLawnmowerLady
@TheLawnmowerLady Жыл бұрын
I do the same thing, but I always lose that tiny octopus looking gadget in my shop. Thanks for watching.
@edwardburke9181
@edwardburke9181 3 жыл бұрын
Nice.... job well done keep e'm coming.
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thank you for watching!
@benhortonben9105
@benhortonben9105 2 жыл бұрын
Great video, really well done.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thank you very much Mr Ben! I appreciate you watching.
@KLRFJR
@KLRFJR 2 жыл бұрын
Great work here, and thank you for not saying "go ahead and..." constantly, like most of the male "experts" do in their videos! Keep up the great work.
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
I appreciate you watching. Cheers!
@BADD400
@BADD400 2 жыл бұрын
Nice work
@TheLawnmowerLady
@TheLawnmowerLady 2 жыл бұрын
Thanks for watching!
@baldeagle242
@baldeagle242 3 жыл бұрын
Another great video, Not Rusty. 😉 I’m starting to wonder if these are the uniforms from all the guys who can’t keep up with you. 🤷‍♂️
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
ZING!
@benrobles752
@benrobles752 3 жыл бұрын
When I work on my Troybilt TB 240 w/ the Honda GCV 160 engine I use two pieces of wood dowel rods cut a bit longer than the carburetor bolts and insert them into the threaded holes in the engine block and assemble as you did. Then pull one rod out insert your bolt, thread on loosely and repeat for the other side
@TheLawnmowerLady
@TheLawnmowerLady 3 жыл бұрын
Thanks Mr. Ben. I actually have some M6 threaded rod just for that purpose. I was really only removing the airbox to make it easier for the camera to see pulling the carb bowl and draining. I wasn't planning to pulling the entire jello filled carb.
GCV160 Honda Carburetor Clean and Tune-up Husqvarna HU700H
34:34
The Lawnmower Lady
Рет қаралды 74 М.
The child was abused by the clown#Short #Officer Rabbit #angel
00:55
兔子警官
Рет қаралды 23 МЛН
БОЛЬШОЙ ПЕТУШОК #shorts
00:21
Паша Осадчий
Рет қаралды 8 МЛН
Please be kind🙏
00:34
ISSEI / いっせい
Рет қаралды 194 МЛН
Was ist im Eis versteckt? 🧊 Coole Winter-Gadgets von Amazon
00:37
SMOL German
Рет қаралды 31 МЛН
HOW TO INSTALL MOST HONDA CARBURETORS / GASKET SEQUENCE!!
16:07
THEMOWERMEDIC1
Рет қаралды 139 М.
How To Clean a Honda Style Carburetor (Step-by-Step)
20:01
Steve's Small Engine Saloon
Рет қаралды 1,5 МЛН
Honda GCV Carburetor Service for Troy-bilt TB240 Lawnmower
22:24
The Lawnmower Lady
Рет қаралды 63 М.
curatare carburator Honda GCV135 GCV160 GCV190
7:38
LEMAGROCHIMgiurgiu
Рет қаралды 185 М.
Cleaning a Honda GCV carburettor
8:34
GardenKit
Рет қаралды 179 М.
Honda HRC216 No Start: GSV160 Carburetor Clean How To
14:54
The Lawnmower Lady
Рет қаралды 164 М.
🍁 Разные взгляды
0:15
Ка12 PRODUCTION
Рет қаралды 5 МЛН
LAVOU TÁ NOVA!
0:11
DAIANE VARGAS
Рет қаралды 46 МЛН
РИСКОВЫЙ ШКОЛЬНИК На велосипеде #shorts
0:15
Леха МАК
Рет қаралды 3,3 МЛН
How did we do? 👀😬😅 @RaenaTripleCharm 🍍 | Gabriella Triple Charm #shorts
0:19
Странные штыри с кольцами из сарая
0:31
А на даче жизнь иначе!
Рет қаралды 6 МЛН